SelectBlinds Tranquil Light Filtering Sheer Shades Installation Guide

SelectBlinds Tranquil Light Filtering Sheer Shades

Specifications

• Product: 2 1/2 Tranquil Light Filtering Sheer Shades CCL & Motorized Lifts
• Installation: Top-Fixing or Face-Fixing
• Bracket Position: Outermost brackets should be at least 5cm away from the ends of the rail, with other brackets evenly distributed across the width
• Child Safety: Chain tensioner included for clutch control shades

The brackets offer two methods of installation:

• Top-Fixing
  Use the front two holes in the top of the bracket to fix to the lintel (the ‘ceiling’ of the recess).

• Face-Fixing
  Use two screws through the back plate to mount onto a facing surface (a wall or window frame)

Note t h a t the position of the outermost brackets should be at least 5cm away from the ends of the rail, with any other brackets evenly distributed across the width.

Fitting the shade

• Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket.
• Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket.

Child Safety

• Shades with clutch controls come with a continuous chain loop, which should always be screwed to the wall with the included chain tensioner.
• The chain tensioner should be installed to a flat surface, so the bead chain is taut but not stretched. Be sure not to twist or cross the chain.
• On inside mount shades, the tensioner may be attached to the windowsill or to the inside of the window frame. For outside mount or wall mount shades, the bracket may be mounted to the exterior of the window frame or the wall.
• With a pencil, mark the desired location of the screw holes for the tensioner and then drill pilot holes. Then install the tensioner with the screws, making sure that the tensioner is fully installed, so that the spring is pushed in and the chain passes smoothly through the guide.
• The chain tensioner forms an important safety function by keeping chain loops away from small children. Never operate this shade without a functioning and correctly installed chain tensioner.
• Please retain these instructions for the future reference.
• Thank you for purchasing this product. Please read the instructions and warning carefully before installation to ensure safe and satisfactory use of this product.

Tranquil Sheer Shades

Installing the no-tools headrail

• Hold the no-tools headrail up against the top of the recess, then push the lever firmly upwards until the rail snaps into place. If the rail is not quite tight enough then this can be easily adjusted:

• • At the end of the rail opposite to the lever there is an adjustment block that allows you to fine- tune the fitting of the rail. Use a flat-head screwdriver to twist the small red plugs in toward the center of the rail. Slide the block out of the rail by a few millimeters, then twist the red plugs back into their original position to fix the block in place. Make small adjustments only, repeating as necessary for a tight fit.

Fitting the shade.
Bracket (side-on)

• Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket.
• Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket

Programming Instructions.

1. Adjust switch on BY or BF working mode

2. BY mode: Short press UP or DOWN button motor in jog rotating, long press UP or DOWN button over 2 seconds motor will rolling up or down continuously.

3. BF mode: Short press UP or DOWN button motor will rolling UP or DOWN continuously

4. Select the Channel for Programming:
   Press “CHANNEL+” or “CHANNEL-” to choose the channel until the LED bright on the channel you want.

5. Programming this channel on the Motor or Receiver:
   Let the motor or receiver under the programming state ( operating according.to the instructions of the motor or receiver)

6. Then press the CONFIRM key on the remote
   ( do it in 6 seconds after the motor under the programming state), the motor jogs, beeps or the receiver beeps to confirm the programming succeed.

FIY : The group channel will be recorded on the motor automatically when the single channel has been programmed.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>