ULTRAVIEW UV Slider BL Mount Sight Instructions

UV SLIDER™
STAY IN THE MOMENT

DIAGRAM

Scope & Drive Assembly

1. UVBXL SE
2. Viz Ring
3. Yardage Indicators
4. Locking Lever
5. Windage Dial
6. Elevation Dial

Rack & Rail Assembly

7. Rail
8. Yaw Block
9.  Rack
10. QuickBreak™ Latch

OUT OF THE BOX

1. Remove the Rack & Rail and the Scope & Drive Assemblies

2. Lift the locking lever fully to unlocked position
   WARNING
   Indicators on the Scope & Drive Assembly are extremely sharp (for pinpoint accuracy) and can poke you

3. To install, lift locking lever, place Scope & Drive Assembly on rack, ensuring guide pins are placed properly in their respective tracks, and slide the Scope & Drive Assembly upward until it clears the spring loaded latch
   You will hear an audible ‘click’

4. Rotate dial to ensure operation is smooth
   Scope & Drive Assembly should slide up and down the Rack & Rail assembly

5. Return locking lever to locked position

BRIDGE-LOCK ASSEMBLY

1. Insert UV Slider™ sight into Bridge-Lock hole in Mathews riser
   Select one of three positions for UV Slider™ sight by aligning its groove to the screw.
   Fasten snugly to secure UV Slider™ to riser.

PICATINNY ASSEMBLY

1. Loosen Picatinny bolt in rail until the clamp opens enough to slide onto Hoyt Picatinny bracket

Choose vertical position, and tighten Picatinny bolt snugly to secure sight to riser

SIDE MOUNT ASSEMBLY

1. Remove riser block from travel case

2. Loosen set screw on riser block before inserting the rail

3. Using the provided %” long low profile bolts, fasten riser block to the side of your bow with the set screw side facing the top of the bow (facing down for left handed users)
   Insert rail into riser block until it is in your preferred position, and tighten set screw snugly to secure sight to the riser

UV3XL SE

1. Turn on UV3XL SE light Fully press and release the button above the “UV”icon

2. Toggle the level light
   With light kit on – Press and hold the power button for 2 seconds, then release. Repeat to turn off level light.

3. Brighten and dim the pin light by pressing the left and right buttons closest to the leading edge of the light cartridge

ADJUSTING ELEVATION

1. Lift locking lever until in the fully unlocked position

2. Rotate elevation dial clockwise to lower sight on rack (increasing yardage)

3. Rotate elevation dial counter-clockwise to raise sight on rack
   (decreasing yardage)

4. When desired elevation position is reached, return locking lever to fully locked position

ADJUSTING WINDAGE

1. To unlock windage adjustment, pull windage dial outward away from the sight until dial clicks into the unlocked position
   Rotate windage dial clockwise to move scope to the right (Moving point of impact left)
   Rotate windage dial counter-clockwise to move scope to the left (Moving point of impact right)

2. When desired windage position is reached, push windage dial towards the sight to return it to the locked position

1ST & ZND AXIS ADJUSTMENT

Using the leveling method of your choosing (With UV Slider mounted on your bow)

1. Locate adjustment screw on yaw block (Intermediate part between Rack & Rail) labeled “1st & 2nd Axis”

2. Unlock the adjustment by slightly loosening the two bolts mounting the yaw block to the rack by one revolution

3. Adjust 1st & 2nd Axis

4. When desired adjustment is reached, slightly tighten the top bolt mounting the yaw block to the rack to hold adjustment in place while you proceed to the 3rd axis adjustment
   IMPORTANT
   This step is very important in assuring the joints are locked correctly at the end of locking the 3rd Axis adjustments

5. UV Slider™ has factory set 2nd axis; when you level the 1st axis, the 2nd axis automatically becomes set

3RD AXIS ADJUSTMENT

1. Locate adjustment on yaw block, labeled “3rd axis”

2. Unlock adjustment by loosening the two bolts mounting the rail to the yaw block one revolution

3. Adjust 3rd Axis
   Right handed Users –
   Turning adjustment clockwise, rotates the Scope & Drive Assembly clockwise in a top-down view
   Left handed Users –
   Turning adjustment clockwise, rotates the Scope & Drive Assembly counter- clockwise in a top-down view

4. When desired adjustment is reached, tighten the two bolts mounting rail to yaw block snugly to lock adjustment

5. Snugly tighten both 1st axis adjustment screws from step 1

QUICKBREAK™

1. Lift the locking lever fully to unlocked position

2. At the bottom of the rack you will find a small silver latch; press and hold the latch down

3. Using the elevation dial, move the Scope & Drive Assembly to the bottom of the rack, and pull the Scope & Drive Assembly downward to remove it fully from the rack

4. To reinstall, unlock elevation, place Scope & Drive Assembly on rack, ensuring guide pins are placed properly in their respective tracks, and slide the Scope & Drive Assembly upward until it clears the spring loaded lacth

SIGHTING IN

1. Remove Setup Tape, position it on tape plate
   Sight in at 20 yards with middle scope pin (Fixed-Yellow)
   Move the set-up tape to align the 20 yard line with black calibration indicator. Fasten down Sight in at 60 yards with middle scope pin (Fixed- Vellow)
   Read the number on Setup Tape scale associated with the closest line to your indicator when sighted in at 60 yards

2. Gap 20/30/40 yard pins
   Before installing the sight tape remove the 3-pin cartridge and align your middle pin with 30 yards on the tape
   Visually align your top pin with 20 yards on the tape
   Align your bottom pin with 40 yards on the tape

3. Install sight tape on scope side of sight
   While still sighted in at 60 yards align your 2nd (Fixed-Yellow) indicator with the 60 yard line on your sight tape
   Fasten the metal tape plate down with screws

4. Set your moving indicators
   Adjust elevation until your 2nd indicator is at the 30 yard line. Verify the 30 yard mark
   Move the top indicator until it aligns with 20 yard line
   Move the bottom indicator until it aligns with the 40 yard line

5. Refine position of top and bottom scope pins by shooting the distances that they indicate

6. Bonus Pin: The 4th ‘Bonus’ pin in the UV3XL SE 3 pin cartridge is meant for fun long range shots and is not meant to be used in conjunction with a sight tape, there is no fixed sight tape indicator present for the bonus pin. This is because when using  multiple fixed pins in a scope, switching between pins causes issues with parallax, causing a discrepancy between sight tape indicators and point of impact.

TROUBLESHOOTING

SCAN FOR INSTRUCTIONS AND VIDEOS
https://ultraviewarchery.com/pages/instructions

GO SHOOT
Vi

WARNING:

A BOW IS A DANGEROUS WEAPON THE USE OF WHICH CAN CAUSE SERIOUS INJURY OR DEATH.
Risks related to bows can be reduced but not eliminated by Safe Handling practices as described below.
You are responsible for familiarizing yourself with these practices prior to using any UltraView product.
You should always use Safe Handling practices while handling or operating a bow, including when not using Ultraview products.
THESE SAFE HANDLING PRACTICES ARE NOT INTENDED TO PROVIDE, SUPPLEMENT, OR SUBSTITUTE FOR A COMPREHENSIVE ARCHER EDUCATION COURSE.
YOU ARE RESPONSIBLE FOR OBTAINING ALL NECESSARY ARCHER EDUCATION AND EXPERIENCE REQUIRED FOR THE SAFE HANDLING AND OPERATION OF BOWS.
THESE SAFE HANDLING PRACTICES SERVE ONLY AS REMINDERS AND IN NO WAY CONSTITUTE ADVICE FROM ULTRAVIEW TO YOU.
Do not point or aim a bow at any person or domestic animal
Always read the user and safety manuals for any archery equipment that You are using for the first time. You should periodically review these materials to remain familiar with their contents.
‘You should be aware of Your surroundings, including environmental conditions that affect a bow’s performance.
You should not fire a bow until You have clearly identified Your target and fully understand what lies beyond the target.
Inexperienced archers and individuals under the age of 18 years old should not handle a bow without appropriate supervision by an adult familiar with the safe handling and operation of bows.
Store Your bow securely in a place inaccessible to children.
Misuse of a bow can cause an unintended flight path of an arrow, resulting in serious injury or death.
Do not shoot an arrow straight up in the air.
Always wear safety glasses when handling or shooting your bow.
Do not drink alcohol or take mood-altering drugs before, during, or after shooting a bow.
Always inspect bow and related equipment prior to each use to ensure that the bow and related equipment are fully operational and safe for use.
Inspect each arrow before use and never use a damaged arrow. A damaged arrow may not fly as expected.
Always draw Your bow pointed at a target.
Handle arrows carefully. Protect yourself and the arrow points with a covered arrow quiver.
Always assume the arrow being used could be released at any time.
Never draw Your bow without an arrow on the string. Accidental release could dry fire your bow, damage Your equipment, and cause serious injury or death to You or third parties.
Never let go of Your release at full draw or during the shot.
Always draw Your bow away from your face. Accidental release could result in serious injury or death.
Always inspect bow and related equipment prior to each use to ensure that the bow and related equipment are fully operational and safe for use.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>