QHYAH 301 Series 60 Inch Modern Ceiling Fans with Remote User Guide

301 Series 60 Inch Modern Ceiling Fans with Remote

301 SERIES
FasterAir Higher Efficiency Less Consumption
USE AND CARE GUIDE
READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION

THANK YOU FOR PURCHASING
We appreciate your purchase of this high-quality product. To guarantee proper operation and safety, it is important that you carefully read and adhere to all instructions before assembling, installing, and using this ceiling fan.

SAFETY NOTICES

A notice that says “WARNING/CAUTION” indicates a potential danger. It is meant to draw your attention to the installation, operation, maintenance, or other procedures that, if not properly carried out, could cause harm to the appliance, yourself, or others, possibly even resulting in death. Therefore, do not proceed beyond a WARNING/CAUTION notice until you fully comprehend and fulfill the specified conditions.

SAFETY PRECAUTIONS

Before and during all stages of handling, installing, removing, operating, and maintaining this product, it is essential to carefully follow the general safety measures outlined below. Not adhering to these precautions disregards the safety standards for the product’s design, production, and intended use, and could result in harm or injury. Please note that we cannot be held responsible for any consequences resulting from the customer’s failure to comply with these requirements.

**** SAFETY WARNING

1. Before installing your new ceiling fan, carefully review the assembly diagrams provided, and read all instructions and safety information.
2. Ensure that a licensed and qualified electrician installs this fan.
3. This appliance is not suitable for use by individuals (including children) with reduced physical, sensory, or mental capabilities or lack of experience or knowledge, unless they are supervised or have been given instructions by a person responsible for their safety.
4. Supervise young children to prevent them from playing with the appliance.
5. All electrical work must be performed only after disconnecting the power supply by removing fuses or switching off the circuit breaker to ensure complete electrical isolation.
6. For outdoor use, install the ceiling fan under covered or enclosed patios, screened porches, and other areas that are not directly exposed to rain, snow, water, or moisture.
7.  This manual is not intended for untrained or unqualified individuals to install the ceiling fan.
8. During installation and operation, it is the responsibility of the qualified and licensed installer and user to exercise common sense and care.
9. The fan, light kit, and mounting plate must be grounded.
10. The use of an unapproved remote control will invalidate the warranty. Only use the provided remote control.
11. Always turn off the main power supply at the main power box before starting any work, and make sure to remove the fuse or turn off the circuit breaker before installing the fan or replacing the LED light.
12. Do not use solid-state controllers with the ceiling fan.

PARTS LIST

Upon opening the original carton, ensure that all items are present and in good condition. If any items are missing or damaged, please contact customer service. Do not dispose of the carton or other packaging materials, as they may be required for warranty replacement or repair purposes.

A Blade x 3
B Canopy x 1
C Mounting Bracket x 1
D Coupling Cover x 1
E Blade Holder x 1
F Motor Assembly x 1
G Bottom Cover x 1
H Downrod x 3
I Motor Wire Terminal x1
J Blade Mounting Screw x 7| K Inner Hexagon Spanner x 1
L Wood Screw x 4
M Wire Connector x 4
N Balance Kit x 1
O 8# 10# Screw & Washer Set x 2
P Remote x 1
Q Holder Screw & Plug x 2
R Remote Holder x 1
S Supply Wire Terminal x 1
T Receiver x 1
---|---

FAN INSTALLATION INSTRUCTIONS

WARNING
Risk of electric shock
WARNING
Installing or using electrical accessories that are not provided with this product is prohibited to prevent fire and electric shock hazards. To prevent personal injury, always disconnect the power supply before installing, disassembling, maintaining, or cleaning the product. If the ceiling fan displays abnormal oscillating movement, cease use immediately and contact the manufacturer, its service agent, or a qualified professional.

1. INSTALL THE MOUNTING BRACKET
The distance from the floor to the lowest point on the fan blade should be no less than 2.1m (7.5ft).
Ensure that the ceiling joists are sufficiently strong and sized to support the weight of the 21kg (45lb) fan. WOODEN CEILING
Fasten the mounting bracket to either the ceiling joist or a suitable piece of timber  inserted between the ceiling joists. Use fourwood screws to attach the mounting bracket. CONCRETE CEILING
Using a percussion drill with an 8mm bit, create holes in the ceiling of a length appropriate for the expansion screws. Once the holes are created, use the expansion screws to attach the mounting bracket to the ceiling.To hang the fan from a flat ceiling, the mounting bracket should be attached securely to the electrical box.To install the fan on an angled ceiling, position the mounting bracket opening towards the peak and attach it to the electrical box.       In case there is no outlet box, follow the instructions below: Firstly, disconnect the power supply by removing fuses or turning off circuit breakers. Next, directly secure the outlet box (A) (not provided) to the building structure using appropriate fasteners and materials that can fully support the weight of the moving fan (at least 35 lbs). Avoid using a plastic outlet box. The figures below demonstrate two alternative methods for mounting the outlet box (not included).
NOTE
To ensure proper clearance between the blade tip and ceiling, a longer downrod may be necessary when installing the ceiling fan on a sloped ceiling. It is important to install the fan at a location where the blades are at least 50cm (20 inches) away from any nearby objects or walls. In cases where there is an existing fixture but no ceiling joist, a ceiling fan hanger bar, Saf-T-Bar or Saf-T-Brace (C) may be required to hang the fan.
2. INSTALL THE FAN BLADES
To install the fan blades, line up the holes on the blades with the holes on the fan motor assembly, and then put the blade holder on the blades by lining up its holes with the blades holes and use the screws and washers provided to secure the blades. Ensure that the blades are securely in place and that the screws used to attach the blades are tightened properly. Install the bottom cover. 3. INSTALL THE DOWNROD
a) Select the downrod size that is appropriate for your ceiling height. This fan comes with 5, 10 and 24-inch downrods to choose from.
b) Detach the screws and hanger ball from the downrod, along with the locking pin, bolt and screws from  the motor coupler.
c) Pass the canopy and coupling cover through the downrod in the proper direction.
d) Pass the motor wire through the downrod in the proper direction.
e) Install the downrod into the motor coupler, attach it with the bolt and locking pin, and tighten the screws to secure it.
f) Insert the hanger ball and bolt on the downrod. Lock them with screws and cover the coupler with the coupling cover. 4. FAN MOUNTING
a) Hang the fan motor assembly on the mounting bracket, and ensure the key slot of the hanger ball is positioned on the key pin of the mounting bracket. b) Plug the motor wire terminal and supply wire terminal into the corresponding wire terminals of the receiver. c) Properly connect the wires: Connect the Neutral (White or Blue) supply wire from the outlet box to the Neutral (White or Blue) fan wire; Connect the Hot (Black or Brown) supply wire from the outlet box to the Hot (Black or Brown) fan wire; Connect the Ground wire (Bare Copper or Green&Yellow) from the outlet box to the fan Ground (Green or Green&Yellow) wire, mounting bracket Ground (Green or Green&Yellow) wire, and downrod Ground (Green or Green&Yellow) wire. Use wire connectors to tightly join each wire together and wrap each connector with approved electrical tape to ensure a more secure connection.d) Slide the remote receiver unit into the mounting bracket as shown in the figure below.e) Loosen the two screws that secure the top canopy to the bottom of the mounting bracket, but only halfway. Slide the top canopy up the downrod and onto the mounting bracket. Rotate the canopy until the screws lock into place, and then tighten them securely. 5. INSTALL THE REMOTE HOLDER
Install the holder to the wall with two wall plugs & two screws provided. Insert the batteries into the remote and hang up the remote by the holder.

FAN OPERATION INSTRUCTIONS

Remote Control Function

1. Fan on/off (Pairing Button)
2. Natural wind mode
3. Fan speed 1-6
4. Fan forward/reverse
5. Timer 1H-2H-4H-8H
6. Battery: 2*AAA (1.5V)

Kindly Reminders

1. The remote and receiver that comes with your fan have already been paired, and the learning code matching mode is only necessary if they lose control at any point.
2. If the remote is unable to control the receiver, check if the battery switch is properly touching and whether the positive and negative are in the correct positions. Also, check if the battery is full or empty of power.
3. If the remote is unable to control the receiver, check if there are any other similar remote-controlled products nearby and whether they are working. Remote-controlled products with the same frequency can interfere with each other.
4. The sensitivity of the remote and signal reception can be affected by the low battery voltage. Replace the battery if the voltage is low.
5. If you are not going to use the remote for an extended period, remove the battery.
6. When installing the fan, ensure that the fan ceiling cover does not press against the antenna or any other wire, as this can cause the wire to break or short-circuit and result in a loss of control.

REPAIRING THE FAN’S RECEIVER & REMOTE

If the ceiling fan remote and receiver lose control after installation or during use, it is necessary to repair the pairing between them. Below are the symptoms and methods to repair the pairing:
Symptoms:

1. The fan only runs at high speed after installation
2. No reverse function after installation
3. Remote cannot communicate with the receiver

To repair the pairing, follow these steps:
a) Turn OFF the main power to the ceiling fan for 30 seconds.
b) Press and hold the Pairing Button on the remote until you hear a double beep ringing within 10 seconds of switching the power ON to the receiver of the ceiling fan. Once the double beep ringing is heard, the pairing is successful.
c) Turn ON the fan and use the remote to change the speed to ensure that the operation and pairing were successful.
When installing multiple fans, each fan must be paired separately. Here are the steps to follow:
a) Turn OFF the main power to both fans for 30 seconds.
b) Press and hold the Pairing Button on the remote for 5 seconds within 10 seconds of switching the power ON to the receiver of the first fan (e.g. “Fan A”). When the double beep ringing is heard, the pairing is successful.
c) Turn OFF the main power to the first fan that was paired (e.g. “Fan A”).
d) Press and hold the Pairing Button on another remote for 5 seconds within 10 seconds of switching the power ON to the receiver of the second fan (e.g. “Fan B”). When the double beep ringing is heard, the pairing is successful.
If you have multiple fans such as “Fan A” and “Fan B” and want to control both with a single remote, ensure that they are located within 10 meters/32 feet of each other in the same room with no obstruction between them. Follow the steps below to pair the remote with both fans:
a) Turn OFF the main power to both “Fan A” and “Fan B” for 30 seconds.
b) Press and hold the Pairing Button on the remote for 5 seconds within 10 seconds of switching the power ON to the receiver of both “Fan A” and “Fan B”. When you hear the double beep ringing, the pairing is successful.

TROUBLESHOOTING GUIDE

1. NON-FUNCTIONING FAN/REMOTE
   Confirm that the remote is within a range of 20 feet from the receiver.
   a) Check that the circuit breakers for the mains are turned ON.
   b) Ensure that the isolation wall switch is in the ON position.
   c) Verify that the battery in the remote is in good condition and inserted correctly.
   d) Follow the remote and receiver pairing process as outlined in the section titled “REPAIRING THE FAN’S RECEIVER & REMOTE”.
   e) Make sure that the live, neutral, ground, and light wires (if applicable) from the isolation wall switch and remote receiver are connected properly as per the wiring diagram.
   f) Verify that all wire connections at the wall switch, wire connector, and/or terminal block are secured and not loose. If the fan still doesn’t function properly, contact customer service.

2. FAN SOUNDS NOISY
   a) Tighten the light fitting completely (applicable to the version with a light).
   b) Tighten all screws on the fan blades again (avoid over-tightening).
   c) Tighten all screws in the hanging bracket and cover the plate again.
   d) Wait for a 24-hour break-in period. Some of the noises that occur with the new fan may resolve during this time.

3. FAN TURNS BUT DOES NOT MOVE MUCH AIR
   a) The fan may be running in reverse (for fans with the reverse running option).
   b) The room may contain items that obstruct the airflow.

4. FAN WOBBLE
   a) Make sure the outlet box is secured firmly to building structure and make sure the mounting bracket is secured to the outlet box, screws are tight.
   b) Check that the screws of hanger ball and motor coupler are tightened firmly with the downrod.
   c) Check and ensure the key slot of the hanger ball is positioned on the key pin of the mounting bracket.
   d) Ensure that all blade are screwed firmly into the blade holder or all blade holders are tightened securely to motor.
   e) If there are any variations in the distance between blades, measure the distance from blade tip to blade tip. Loosen the screws connecting blades and brackets (one at a time), adjust the blade to the correct position, and then tighten the screws again.
   f) If the fan blades are still wobbling, try swapping two adjacent (side-by- side) blades to distribute the weight more evenly and achieve smoother operation.
   g) If blade wobble is still noticeable, use the included blade balancing kit.

HOW TO USE BALANCING KITS

To help you balance the fan, a balancing kit is provided for your convenience. Here are the steps to follow:

1. Ensure that all the blades and blade arm screws are properly tightened.
2. Uneven blade levels are often the cause of fan wobbling issues. To check the level, choose a point on the ceiling directly above one of the fan blade tips and measure the distance. Rotate the fan until the next blade is in position and measure the distance again. Repeat for all blades. The difference in distance should not exceed 1/8” (0.32cm).
3. If blade wobbling is still noticeable, use the included blade balancing kit.
4. If the fan blades are still wobbling, try swapping two adjacent (side-by-side) blades to distribute the weight more evenly and achieve smoother operation.

IMPORTANT FACTS

WARM NOTE
All electric motors, including fan motors make some noise and may feel hot to touch, this is not a fault. Ceiling fans tend to move during operation as they are not generally rigid-mounted. Movement of a couple of centimeters is quite normal and does not suggest the fan will fall. Rigidly mounted ceiling fans generate excessive vibration and stress on their mountings. Fan lights will rattle if they are not supplied with the fan. And this is not covered by warranty.
FAN OPERATION
A ceiling fan is an environmentally smart choice when it comes to cooling as well as helping to warm your room. You should see a reduction in both cooling and heating costs by regular use of your fans. Do not hesitate to use your fans in both the summer and winter months. In summer, the fan should be set to spin in an anti-clockwise direction blowing down the cool breeze. In winter, the fan should be set to spin in a clockwise direction so that an upward airflow will push warm air off the ceiling and circulate it downwards into the living areas. In winter months use the fan at a lower speed than in summer.
NORMAL WEAR AND TEAR T
hreaded components working slightly loose, or blade carriers becoming slightly bent due to vigorous cleaning or bumping can cause extra wobble and noise. This is not covered under warranty, but a little care and maintenance can reduce or prevent this problem.
NIGHT NOISES
This is the biggest cause of service calls, which are outside the manufacturer’s warranty. If a fan has a fault it will be noticeable at all times. Naturally, when everything is quiet at night you will be more inclined to hear small noises, which may not be noticeable at other times. Even slight signals superimposed in your electricity supply for off-peak hot water control may cause a change in the fan motor noise. This is normal.

Customer Service
Check that all parts are available before beginning assembly.
Do not attempt to assemble the product if any parts aremissing or broken.
If you encounter any problems before and during the installation, please feel free to contact us.
https://wa.me/qr/3AROPIB7DBVPG1
Technical Support: [email protected]
Business Cooperation: [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>