MISULI MD06 MD Wireless Smart Headphone Instruction Manual

MD wireless smart headphones Instruction manuall

CONFIGURATION PARAMETER

Pairing Name: MD
Chipversion: 53
Charging nterface: type-C
standby time: 240 hours
talktime: About 48H
charging time: About 12

PRODUCT INTRODUCTION

1. chargingbox*1
2. Leftand right headphones*1
3. chtaline*1
4. Product specifcation*1

BINAURAL PAIRING CONNECTION

1. Pick up the headphones and automatically start the mutual configuration. The mutual configuration is successful. The white and green lights of the main headphones flash alternately, and the LED lights of the auxiliary headphones go out (if there is no mutual configuration, just double-click any headphones to configure each other).
2. Open the Bluetooth device list and search for “md528/538”;
3. Click to complete the connection (LED light goes out).

If the connection fails, put the headset back into the charging box, close the cover and repeat the above operation.
When both ears leave the device at the same time and exceed the distance, the headset enters the back connection state. If there is no back connection to the device within 3 minutes, the headset will automatically shut down. After the first connection, the headset will automatically connect back to the last paired device after it is restarted (if the Bluetooth of the mobile phone is turned on)

Switch between English and Chinese

Headset boot without connecting any device in the case of Boot, press 5 buttons (quick press) can be switched between English and Chinese freely.

OPERATION MODE

1. POWER ON
   (1)Pick up the headset immediately automatic boot, green light for 1 second.
   (2)When the headset is off, press and hold the function key for 1 second, and the voice prompt “Power on” green light for 1 second.

2. SHUT DOWN
   (1)Put the headphones back into the charging box and close the lid. When charging, the headphones “Automatically turn off’ white light for 1 second
   (2)In the case of headphone boot, long press function key 3 seconds headphone off, voice prompt “Off” white light for 1 second.

3. Restore factory settings
   When the headset shuts down, press the function key for 8 seconds, the voice prompt “Shuts down” the white light is on for 1 second, then the factory setting is restored.

OPERATING INSTRUCTIONS

Volume+
Music state
Right ear (R) click twice
Play the next song
Music state
Right ear (R) click three times
Voice assistant
In the connected state
Long press any headset
1.5 seconds
Answer / end a call
Connected
L/R headset click once
Refuse to answer the phone
Long press any headset 1.5 seconds
Play / pause music
Connected
L/ R headset click once
Volume-
Music state
Left ear (L} click twice
Play the previous song
Music state
Left ear (L) click three times

Product warranty card

This card is the product warranty certificate, please keep it properly

| Undesirable phenomenon|
---|---|---
| |
| |

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference.
   (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement
The device has been evaluated to meet general RF exposure requirement, The device can be used in portable exposure condition without restriction.

certificate
inspector : 08

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>