Maidesite M021 Electric Standing Desk Instruction Manual

: May 16, 2024
: MAIDeSITe

Table of Contents

Safety & Warnings
Parts List
Hardware List
Standing Desk Assembly
Accessories Installation
Hand Controller Instruction
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Maidesite M021 Electric Standing Desk Instruction Manual

Safety & Warnings

Warm prompt

Make sure no obstacles are in the desk’s path.
Make sure the desktop is not touching any walls. Make sure all cords are appropriate length to accommodate the change in height.

Keep children away from electric height-adjustable desks, control units and handsets. There is a risk of injury and electric shock.

Keep all electrical components away from liquids.

Do not sit or stand on the desk frame. Do not crawl or lie under the desk frame.

Do not place any objects taller than 20″ underneath the desk.

Do not open any of the components – the Legs, Control Box, or Switch.
There is a danger of electric shock.

This product is designed with a duty cycle of 10% (2 min. on, 18 min. off).

In the event of a power outage or if the power cord is unplugged, a manual reset may be necessary – see USE section.

USE/ LIABILITY

This height adjustable desk has electric motors and is designed for use in dry work areas only.
The desk height is adjustable so that it can be positioned at the most ergonomically suitable height.
Any other use is at user’s risk.
Under no circumstances does the manufacturer accept warranty claims or liability claims for damages caused from improper use or handling of the desk frame.

Parts List

A. Desktop
Parts List
B. Right Lifting Column (with movement).

C. Left Lifting Column

D. Side Bracket ×2

E. Foot ×2
Parts List
F. Frame

G. Drive Rod

H. Power Adapter

I. Power Adapter Fixture

J. Handset

K. Power Cable

L. Hook ×1

M. Caster ×4

N. C-Bracket ×2

O. Wire Management Tray

P. Felt Side Storage Bag

Q. Drawer

R. Cable Clip ×4

Hardware List

Back-up Screws
M6*35 Hexagon Screw ×8
M6*16 Hexagon Screw ×4
M6*14 Hexagon Screw ×25
ST4.8*15 Tapping Screw ×34
M4 Allen Wrench
Washers × 8
M6*8 Hexagon Screw ×4
Screwdriver
M6 Nuts×7
M14 Open End Wrench
Fixing Plate ×6
Wood Dowel Pins ×8
ABS Round Spacer ×2
ST4*30 Tapping Screw ×2

Standing Desk Assembly

STEP 1 Desktop Assembly

STEP 2: Assemble the Frame

STEP 3: Assemble the Feet

Note: Two persons are needed at this step to avoid lifting columns falling and damaged.

STEP 4: Assemble the Drive Rod

STEP 5: Install the Side Bracket

STEP 6: Adjust the Frame and the Length of the Drive Rod

STEP 7: Assemble the Frame and the Desktop

STEP 8: Secure the Frame and the Drive Rod

STEP 9: Install the Power Adapter

(Pay attention to the direction of the power adapter.)

STEP 10: Install the Handset

STEP 11: Connect Wires

Connect the power cable, wires on the handset and the motor to corresponding ports, which can be fixed under the desktop with cable clips.

Accessories Installation

Install the Hooks

Install the Casters

Two Mode
You can choose whether to install casters according to your personal preference.
Install the Casters

Install the Wire Management Tray

Install the Drawer

STEP 1: Install the ABS round spacers, as the limit, with 2 ST4*30 tapping screws.
Install the Drawer

STEP 2: Unfold the fabric drawer and put it over the limit upside down.
Install the Drawer

STEP 3: Bend the fabric drawer bracket along the bend line and place it on the top of the drawer. Secure it on the desktop with 6 ST4.8*15 tapping screws.
Install the Drawer

Install the Felt Side Storage Bag

Congratulations! The installation is completed. The following step is to debug the hand controller.

Hand Controller Instruction

CAUTION

Please RESET the desk at first time.
Please ensure that no objects (walls) will interrupt the movement of the desk, and all cables of relevant devices are sufficiently long

RESET: Long press the down key until the desktop reaches the lowest position; long press the down key again, when it shows”RST ”on the digital display, the desk is in initialization mode. Release the down key when the buzzer rings, the initialization succeeds.

PS. If the system is abnormal or the digital display shows”RST ”, the desk needs to be initialized as written above.
Hand Controller Instruction

The following steps can be set according to personal preference.

Memory Height
Press the“m” key until it displays “ S – ”; press one of the memory keys(number keys) and the current height will be recorded.

Switch between Centimeter and Inch
Long press the“m” key for 5 seconds until it displays “S-1”and “1”flashes.
Press the“m”key again to set:
0 = cm
1 = inches

Exit to operation interface by pressing the“m”key after setting.
Switch between Centimeter

Anti-collision Sensitivity
（1）“S-3”anti-collision sensitivity while going up Long press the“m”key for 5 seconds until it displays “S-1”and “1”flashes. Press the“up”key to switch to“S-3”; press the“m”key to set up sensitivity :
0= Closed 1=Minimum Sensitivity …… 8=Maximum Sensitivity
Exit to operation interface by pressing the“m”key after setting.
Anti-collision Sensitivity

（2）“S-4”anti-collision sensitivity while going down Long press the“m”key for 5 seconds until it displays “S-1”. Press the“up”key to switch to“S-4”; press the“m”key to set up sensitivity : 0= Closed 1=Minimum Sensitivity …… 8= Maximum Sensitivity Exit to operation interface by pressing the“m”key after setting.

Switch between Jog and Continuation at Memory Height
Long press the“m”key for 5 seconds until it displays “S-1”and “1”flashes.
Press the“up”key to switch to“S-6”; press the“m”key to set: 0=Jog (Long press a memory key 1/2/3/4, and it will stop after release) 1=Continuation (Press a memory key 1/2/3/4, and it will goes to default height automatically)
Exit to operation interface by pressing the“m”key after setting.
Switch between Jog

Lock & Unlock
Lock: Press both the “m” and “up” keys for 5 seconds, when it displays”LOC”, the system is locked and the desk can’t go up or down.
Unlock: Press both the“m” and “down” keys for 5 seconds, when it displays a number, the system is unlocked.

Factory Initialization
If a new desk frame is replaced or to initialization default data; press both the“up” and “down” keys for 10 seconds, the system is initialization to default data after the buzzer rings once again, and it will display“RST”； the system is restored to its original settings.
Factory Initialization

Max. Height Limit （96cm-120cm)
Adjust the desk to the target Max. height limit; press both the“up” and “down” keys for 5 seconds; the height limit is restored after the buzzer rings.
$Max. Height Limit （96cm-120cm\)$

Min. Height Limit (72cm-96cm)
Adjust the desk to the target Min. height limit; press both the“up” and “down” keys for 5 seconds; the height limit is restored after the buzzer rings.
$Min. Height Limit $72cm-96cm$$

Cancel the Height Limit
RESET: the desk and the height limits will be auto-canceled.

USB Port
Output Voltage: 5V
Output Current: 0.8A

Error Codes & Solution

Error Code	Description	Solution
E01	The voltage of the main power supply is over 45V.	Check the main power

If there are any questions, please feel free to contact us!
Email(EU): Customerservice-EU@maidesite.com
Website(EU): www.maidesite.de
Website(UK): www.maidesite.co.uk
YouTube: Maidesite Office
Facebook: Maidesite Desk
Instagram: Maidesite Standing Desk