OrangeLion OL01 Keyless Entry Deadbolt Lock Installation Guide

Orange Lion OL01 Keyless Entry Deadbolt Lock

Important tips to ensure a successful installation:

• Always reset your lock after installation.
• Do not use electric drill to tighten screws.
• Wait to install the batteries until instructed to do so.
• Do not insert the backup key before the lock is fully installed.
• Change the default master code before programming.

Questions

Please contact us at support@OrangeLionTech.com

installation Overview

Read this manual carefully before installing and operating!

1. Install the physical lock Step 1-7
2. Detect door orientation Step 8-9
3. Change the default master code See Programming & Use
4. Customize setting See Programming & Use

Contents

Installation

STEP1 Prepare the door and check dimensions

STEP2 Determine backset and adjust the latch

Hold the latch face flush against the door edge. Is the slotted hole centered?

YES Slotted hole is centered.
No adjustment is required. Proceed to the next step.

NO Slotted hole is NOT centered.

Rotate the latch as shown to extend latch.

STEP3 Install the latch

STEP4 Install strike and test alignment

MPORTANT: Make sure the hole in the door frame is drilled at a minimum of 1″ (25 mm) deep

1.  With the door closed, use flat-head screwdriver to test if deadbolt works smoothly.
2.  Check alignment between the latch and the strike, making sure when the deadbolt is extended, it is going into the bolt hole and nothing the deadbolt strike.

STEP5A

Install exterior assembly

Do not insert the physical key until lock is completely installed.

1.  Before installation, make sure the latch is fully retracted (unlocked) .
2.  Route the cable below the latch.

STEP5B Secure the mount the mounting plate screws I.

STEP6 Remove battery cover

Do not load batteries until lock is completely installed.

STEP7A Install interior assembly

STEP7B

STEP7C

Attach Interior Assembly to Mounting Plate and tighten 3 screws.

Test the thumb-turn for smooth rotation.
If thumb turn doesn’t rotate ,repeat step 7B, making sure the thumb turn is vertical and rotate with more force.

STEP8A Handing of Door/Factory Reset

Always run this step after installation.
The motor will not operate before completing the step.

While the door is OPENED and UNLOCKED (latch retracted), load 3 AA batteries into the battery compartment.
NOTE: For best results, use new, non rechargeable Alkaline batteries only.
Do not mix old and new batteries.

STEP8B

Hold the reset button while loading the 4th battery.
Keep holding the reset button, until the latch bolt extend.

If the latch doesn’t extend within 10 seconds after doing this step 8B, please repeat step 7B and 8A to make sure the thumbturn is always vertical and latch is always retracted

STEP9 Test the lock

Test with the door open to avoid an accidental lock-out.

Programming & Use

UNLOCK from outside

Press any key to activate.
2 Enter Master code / User
code.
3 Press to confirm.

LOCK from outside

Press and hold any key for 2s.
OR
Enable Auto Lock.

LOCK & UNLOCK from inside

• Rotate the thumb turn to lock or unlock position.

A Master Code

• · Master code is the administrative code for programming. It will also unlock the door. The default master code is 12345678.
• For security reason, the default master code does not program the lock. You must change it to a code of your own prior to programming.

B Code Format

•  Code is 4-10 digits long.
• Codes with the following sequence are not supported

a. forward number sequence
b. Backward number sequence
c. Repeat number sequence
d. Contain existing code sequence

C Wrong Entry Limit

• After 10 unsuccessful attempts at entering a valid code, lock unit will shut down for 3 minuets.

D Unlock with Fake code

User can prevent pin code exposure from strangers by entering random digits before or after pin code.

E Battery Indicator

If you see 10 red flashes after pressing any key or lock and unlock the door, that’s an indication that the batteries need to be replaced soon.
Please replace with 4 new AA alkaline batteries and do not mix old and new batteries. All settings are retained in the memory when the batteries are removed and replaced

F Key Override

• Key Override can be used to gain access when the batteries are completely dead or when no valid User Code is known.
  Important Note:
  please keep at least one copy of the backup key in secure location outside of your place.

Programming Tips:

•  During programming steps, the Orange Lion button turns green to indicate that you can proceed.
• Please proceed to the next step before the goes off.
• f you hear 6 rapid beeps with flashing red lights, it indicate sentry error. Please start over.
• Before programming, press the Orange Lion button to activate the keypad.

A. Change Master Code

The default Master Code is 12345678. It is required that you change it to a code of your own before programming.

Master Code New Master Code

Enter the New Code Again

B Add User Code

• Up to 20 User Codes can be stored.

Master Code New User Code

Enter the New User Code Again

C Delete User Code

Master Code Unwanted User Code

D. Enable Silent Mode

• The beep sounds when pressing keypad can be muted. But you will still hear low battery and system alerts.

Master Code

F Enable Auto Lock

• Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default.

Master Code

G. Disable Auto Lock

Master Code

H. Set Auto Lock Time Delay

• You can set the Auto Lock time delay between 10 and 99 seconds.

Master Code Enter New Duration Time (10-99 seconds)

Enter the New One-Time Code Again

I Add One-Time Code

Master Code New One-Time Code

Enter the New One-Time Code Again

J Vacation Mode

• This is a security feature for you when you are leaving your home for vacation. Enabling vacation mode will restrict all user codes until master code is entered on keypad. If the lock is unlocked by thumb turn, the lock will sound an alarm.

Master Code

Factory Default Settings

How To Reset

By performing the steps below, you will teach the lock the orientation of your door and reset all customize settings.

Step1 Keep the door opened, latch retracted and thumbturn vertical.

Step2 Press and hold the reset button with one hand and the other hand takes out one battery and places it back Keep holding the reset button until the latch extends.

Safety Warnings

• Protect your Master Code.
• Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• Proper cleaning and maintenance of your lock ensures it will continue to work as it should.
• Do not apply cleaner or detergent directly to any part of the lock.
• The Orange Lion lock meets IP54 water-resistance. It can withstand waters plashes ; however, do not let water and liquids get into the lock.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.
• The temperature range of the Orange Lion lock is between -4°F to 129°F.

Troubleshooting

Solutions

A

| The latch and strike are misaligned, causing the latch to bind.

① Adjust the position of the strike plate on latch bolt.

② Make sure you reset the lock with the door opened.

B| Residual charge of internal electronic components. Disconnect all batteries. Press and release any key on the keypad and keep the batteries disconnected for at least 5 minutes. If there is residual charge within the lock, this will consume the charge.
C| Slightly loosen the screws(H and I) that secure the latch bolt and exterior keypad.
D| Assemble the lock without securing screws on hand. Reset the lock and test locking and unlocking.
E| Make sure the lock was properly reset. Once reset is completed, all codes and settings will be erased and the master code will return to the default value (12345678).
F| Door handing is the same as factory reset. Your lock has restored to factory default. Re-program your codes.
G| Take the next button within 5 seconds.

Change the default master code before programming.

Enter a new code in correct format and within 4 to 10 digits.

H| Re-install the whole lock, make sure the thumbturn is vertical and the lock is unlock when installing. Do not insert the backup key.
I| Make sure the cable is properly connected.
Change the batteries with 4 fresh AA standard alkaline batteries. Do not mix old and new batteries.
J|  Make sure the bolt hole on the door frame is at least 1 inch deep so the bolt fully extends.
Make sure when the deadbolt is extended, it is going into the bolt hole and not hitting the deadbolt strike or door frame. Check for loose door hinges.

• If none of the above resolves your issue, please contact us at Support@OrangeLionTech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>