AQUA CUBE FMCG Ultimate Boot Washer Instruction Manual
- June 14, 2024
- AQUA CUBE
Table of Contents
The Ultimate Boot Washer
Operating Instructions
FMCG Ultimate Boot Washer
Operating Instructions
- Provide to user
- Read carefully before use
- Keep safe for future use
General Provisions
The premium boot cleaner is state-of-the-art technology and complies with
approved technical safety regulations.
The boot cleaner may only be used in a technically flawless condition in the
version delivered by the manufacturer.
For safety reasons, modifications to the boot cleaner are not permitted
(except the addition of accessories specially provided by the manufacturer).
1.1 Safety
Each boot cleaner is tested for functionality and safety before dispatch. When
used as intended, the boot clearer is safe to use.
Incorrect operation or misuse poses a dangerous risk to:
- Life and limb for the operator.
- The boot cleaner and other property belonging to the user,
- The functionality of the boot cleaner
In order to avoid risks to people, animals and property, please read these
operating instructions prior to using the boot cleaner for the first time, in
particular all safety instructions.
Ensure that:
- You understand all the safety instructions,
- The operator of the boot cleaner informed about the instructions and understands them,
- The operating instructions are to hand and placed near the boot cleaner.
1.1.1 Maintenance & Monitoring
The boot cleaner must be regularly checked to ensure it is in a safe
condition.
This check shall Include:
- Visual inspection for leaks,
- A functional test,
- Firm fit of the floor mounting (accessory).
1.2 Using Original Parts
Please only use original parts provided or recommended by the manufacturer.
Also take note of all safety and usage information provided with these parts.
This applies to:
- Spare parts and wear parts,
- Parts for accessories
1.1.3 Operating the System
In order to avoid any hazards due to incorrect operation, the boot cleaner may
only used by individuals who:
- Have read and understood the instructions.
- Have proven their ability to operate the equipment
- Have been assigned to use the equipment.
- Have the physical capabilities to use the boot cleaner.
Important:
The operating instructions must be easily accessible for each user.
1.1.4 Other Applicable Documents & Regulations
Country-specific regulations and laws
Regulations of the water supply company
1.2 Intended Use
The intended use of the premium boot cleaner is exclusively to clean dirty
footwear (boots) suitable for cleaning with water.
The maximum water temperature must not exceed 40°C.
Only for use with water without additives.1.2.1 Summary
Any other use is not intended!
For safety reasons, modifications to the boot cleaner are not allowed (except
for the addition of accessories specially provided by the manufacturer). The
intended use assumes compliance with all information in these operating
instructions.
1.3 Inappropriate Use
Important:
Inappropriate use also includes failure to comply with the information in
these operating instructions.
It also includes:
- Non-observance of the respective applicable national regulations.
- Use of liquids other than those stipulated under intended use, e.g.: additives such as disinfectant
Technical Data
| Premium Boot Cleaner
---|---
Dimensions [cm]|
– Length| 52
– Width| 47
– Height| 90
Weight [kg]| 15
Hose Connection [“]| IA
Outlet Connection [“]| 134
Max operating pressure [bar]:| 6
Max water temperature [°C]| 40
Stationary brushes| 3
Moveable Hand Brush| 1
Pipes:| Stainless Steel
Handles:| Integrated
Ball Valve:| 2x
Scraper Grate for Coarse Dirt| Accessory
Design
- Connection for 1/2″ hose
- Handles
- Ball valve hand brush
- Ball Valve Stationary Brush
- Movable Hand Brush
- Water outlet pipe
- Side stationary brush
- Bottom Stationary Brush
- Wastewater drain
- Hose clamp (2 Nm)
Initial Operation
The boot cleaner must be placed on a level, non-slip and horizontal surface.
The unit must not be connected directly to the public drinking network.
The regulations of the water supply company must be observed.
The connection is made via a water hose which is attached to the 1/2 ” hose
nozzle with a hose clamp.
The tightening torque of the hose clamp is 2 Nm.
Operation
The boot cleaner should not be exposed to direct sunlight for long periods of
time.
Excessive heating can lead to deformation of the high-quality plastic housing.
Suitable operating conditions are at 0°C to max +40°C.
If there is a risk of frost, disconnect the boot cleaner from the water supply
and empty it.
The water supply to the stationary brushes and to the hand brush can be
controlled seperately via a ball valve.
Water is applied to the brushes at an angle from above through 3 holes on each
side of the water outlet pipe.
The wastewater is discharged on the left side (1 1/2″ thread).
The wastewater generated must be disposed of in accordance with local
environmental regulations.
The sole and sides of the boots can be cleaned with the 3 stationary brushes.
Operating Instructions
To clean the boot shaft, also use the movable hand brush.
The water flow of the movable hand brush can be changed by turning the orange
handle.
The hand brush can be mounted as shown in the picture.
Make sure that it is in a secure position when in use, and use the integrated
handles.
Close the ball valves after use.
Maintenance & Inspection
6.1 Safety Measures
Important:
The operator must provide any protective clothing that may be required.
Who can carry out maintenance and inspection work?
Normal maintenance work can be carried out by trained operating personnel.
6.2 Maintenance & Inspection Table
| Interval | Assembly | Action |
|---|---|---|
| Before use | Wall Mounting | Check for tight fit |
| As required | Inside and outside of boot cleaner | Remove any dirt that has |
accumulated
Monthly| Housing| Visual Check for Damage
Line/hose system| Check hoses for cracks & porosity, check fittings for leaks
(replace defective parts).
Hose clamp| Check for tight fit
6.3 Troubleshooting
| Fault | Possible Cause | Solution |
|---|
No or not enough water
from the hand brush| Ball Valve Closed| Open ball valve
Hose kinked| Remove kink
Flow control on the
hand brush closed
Open the flow| control on the hand
brush
Accessories/Spare Parts
7.1 Spare Parts
Spare Hand Brush
- Waterfeed with flow valve
- Simple installation
Product Code: WF01
- Waterfeed with non flow valve
- Hard and Sturdy Bristles ensures a deep clean
Product Code: WF03
Spare Brush Set
- Hardy Bristles for reliable cleaning
- Easy and Hassle-free installation
Product Code: AQCBR
7. 2 Accessories
Metal Grate
For Aqua Cube
- Sturdy Metal Construction
- Scrapes off Heavy
- Soiling Simple installation into existing
- Aqua Cube systems
- Best for the Mining Industry
- Product Code: AQCGR
Sanitiser Dosing Unit
- Easily configure dilutions using the broad range of included coloured tips
- Small and compact size makes installation easy
Product Code: DMDSWL
Decomissioning
- Drain the system completely.
- Disassemble the system into its constituent parts.
- Sort according to material characteristics.
- Dispose of in compliance with local regulations.
Warranty
Under our general terms and conditions of trade, we guarantee that the boot
cleaner will be produced free from defects in materials, functionality or
workmanship.
These can be viewed at: https://www.fmcgis.com.au/termsandconditions/
The warranty applies only under the condition that the above operating and
maintenance instructions and all applicable regulations are closely followed.
Any modification of the boot cleaner by the customer without consultation with
the company FMCG Industry Solutions shall invalidate any claims under the
statutory warranty.
FMCG Industry Solutions also accepts no responsibility for damage caused by
inappropriate use.
ADDRESS
Unit 11A, 1 – 3 Endeavour Road
Caringbah, NSW 2229
TELEPHONE
sales@fmcgis.com
1300 628 104 or (02) 9540 2288
EMAIL
sales@fmcgis.com.au
WEBSITE
www.fmcgis.com.au
Prices exclude GST
sales@fmcgis.com.au
Call Us 1300 628 104
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>