Toolsempire AT4768 2 Ton Underhoist Safety Stand Installation Guide
- June 14, 2024
- Toolsempire
Table of Contents
Toolsempire AT4768 2 Ton Underhoist Safety Stand
Product Information
The 2 Ton Underhoist Safety Stand, item number AT4768, is designed to provide support and stability when working on vehicles.It is equipped with various components such as L-Bracket, ComponentHardware, Bolt M8X20, Washer 8, Nut M8, Pull rod, Support pillar, Lock plate, Handle, Bearing base, Column, Thread rod, Bolt M8X16, Washer M12, and Hitch pin clip.
Product Usage Instructions
- Assembly:
- Attach the L-Bracket (middle bridge) (7) with the Component Hardware (8) using Bolt M8X20 (4), Washer 8 (5), and Nut M8 (6).
- Attach the Pull rod (11) with the Support pillar (10) using the plain Washer M8 (13) and Bolt M8X16 (12).
- Mount the Component (8) with the Support pillar (10) using plain Washer M8 (13), Bolt M8X20 (15), and Nut M8 (16).
- Mount the Lock plate (9) with the Support pillar (10) using plain Washer M8 (5), Bolt M8X25 (4), and Nut M8 (6).
- Attach the Column (20) with the Handle (17) and install the bearing assembly by first installing the Bearing base (18). Screw the Handle (17) into the Threaded rod (19) and insert it into theColumn (20). Adjust the position of the stand using the Lock bolt(21), plain Washer M12 (22), and Hitch pin clip (23).
- Attach the saddle bracket using Bolt M8X20 (15).
- Safety Warnings:
- Use the product for its intended purpose only.
- Ensure the product is used on a flat, level, hard surface capable of supporting the stand and load.
- Inspect the product before use and do not use if any parts are loose or damaged.
- Do not exceed the maximum weight capacity of 2 tons.
- Wear ANSI approved safety goggles and work gloves during use.
- Read the manual before setting up or using the product.
- Ensure the hoist used to lift the car or truck is in good working order and securely locked into place after reaching the desired height.
Parts List:
| Index | Description | Quantity |
|---|---|---|
| 1 | Bolt M6X10 | 4 |
| 2 | Rubber Pad | 13 |
| 3 | Washer M8 | 18 |
| 4 | Bolt M8X20 | 7 |
| 5 | Bolt M8X25 | 3 |
| 6 | Nut M8 | 6 |
| 7 | L-Bracket | 1 |
| 8 | Component | 3 |
| 9 | Lock plate | 1 |
| 10 | Support pillar | 3 |
| 11 | Pull rod | 3 |
| 12 | Bolt M8x16 | 12 |
| 13 | Washer M8 | 3 |
| 14 | Short pull rod | 3 |
| 15 | Bolt M8X20 | 4 |
| 16 | Nut M8 | 3 |
| 17 | Handle | 1 |
| 18 | Bearing base | 1 |
| 19 | Thread rod | 1 |
| 20 | Column | 1 |
| 21 | Lock bolt | 1 |
| 22 | Washer M12 | 1 |
| 23 | Hitch pin clip | 1 |
SET UP AND OPERATING INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury. Save this manual
Safety Warming
- Use for intended purpose only.
- Use on flat, level, hard surfaces capable of supporting stand and load.
- Inspect before use, do not use if parts are loose or damaged.
- Do not exceed 2Ton maximum weight capacity
- Wear ANSI-approved safety goggles and work gloves during use.
- Read the manual before setting up and or use
- Make sure the hoist used to lift the car or truck is in good working order and securely locked into place after reaching the desired height
Assembly
- Attach L-Bracket(middle bridge) (7) with Component Hardware (8), using Bolt M8X20 (4),Washer 8 (5), Nut M8 (6).
- Tri-pod Assembly:
- Attach the Pull rod (11) with the Support pillar (10), using the plain Washer M8 (13) and Bolt M8X16 (12).
- Attach the Short pull rod (14) with the Support pillar (10) using the plain Washer M8 (13) and Bolt M8x16 (12)
- Mount the Component (8) with the Support pillar (10), using plain Washer M8 (13) ,
- Bolt M8X20 (15) and Nut M8 (16)
- Mount the Lock plate (9) with Support pillar (10), using the plain Washer M8 (5), Bolt M8X25 (4) and Nut M8 (6)
- Attach Column (20) with Handle (17), install bearing assembly: first install Bearing base (18), screw the Handle (17) into the Threaded rod (19) and insert to Column (20). To adjust the position of the stand, use the Lock bolt (21), plain Washer M12 (22) and Hitch pin clip (23)
- Attach the saddle bracket, using bolt M8X20 (15)
Parts List
| Index | Desc. | QTY | Index | Desc | QTY | |
|---|---|---|---|---|---|---|
| 1 | Bolt M6X10 | 4 | 13 | Washer M8 | 18 | |
| 2 | Rubber Pad | 1 | 14 | Short pull rod | 3 | |
| 3 | Saddle | 1 | 15 | Bolt M8X20 | 7 | |
| 4 | Bolt M8X25 | 3 | 16 | Nut M8 | 6 | |
| 5 | Washer 8 | 3 | 17 | Handle | 1 | |
| 6 | Nut M8 | 3 | 18 | Bearing base | 1 | |
| 7 | L-Bracket | 1 | 19 | Thread rod | 1 | |
| 8 | Component | 3 | 20 | Column | 1 | |
| 9 | Lock plate | 1 | 21 | Lock bolt | 1 | |
| 10 | Support pillar | 3 | 22 | Washer M12 | 1 | |
| 11 | Pull rod | 3 | 23 | Hitch pin clip | 1 | |
| 12 | Bolt M8x16 | 12 |
Read User Manual Online (PDF format)
Loading......