NXGKET 813 Walkie Talkies for Adults Kids User Manual
- June 14, 2024
- NXGKET
Table of Contents
NXGKET 813 Walkie Talkies for Adults Kids
INTRODUCTION
Safety Attention and General Information
NOTICE
Please charge for 4 hours first when you receive the walkie talkies.
- Make sure the channel is correct every time you turn on the walkie talkie. To avoid unnecessary errors, please make sure all the walkie talkies remain on the same channel.
- Keep the walkie talkie upright and ensure its microphone is 3-5cm away from your mouth when you’ re talking.
- Keep the device away from high temperature, dampness, flammable gas, or gas station during use.
- Please hold the device by the main body instead of antenna to avoid possible damages and impact on conversation.
- Don’t frequently turn on and off the device during use. Adjust the volume to a proper level.
- To prevent any problem caused by electromagnetic interference or electromagnetic compatibility, please turn off the device on the areas that are marked with off the walkie talkie, e.g. hospital, airport, gas station or other occasions.
- Do not use the walkie talkie if its antenna is damaged.
- If the device didn’t give you response after pressing a specific button,its keypad may be locked. ****To unlock the keypad, just press and hold the Lock button for 3 seconds until the A symbol disappears.
Product Illustration
Power/Scan button
- Scan channels
- Turn on/off the device
Up & Down buttons
- Adjust volume levels
- Alter settings
Call/Ring button
- Send a ringtone
Menu/Lock button
- Select menu settings
- Lock/unlock the keypad
PTT button
- Make a conversation
- Confirm settings
LAMP Button
- Turn on the
- flashlight
Belt Installation
-
Pry the elastic buckle out
-
Push the belt clip upward
There is a battery indication on the LCD screen. When the full capacity symbol a turns into empty capacity , the walkie talkie will beep periodically after releasing PTT button. To prevent automatic shutdown or abnormal use, please charge the walkie talkie by using our USB Type-C Charging cable, in normal, 3-4 hours to fully charge
Operation Instruction
Power on/off
- To turn on the unit, press and hold the Power/Scan button for 3s.
- To turn off the unit, press and hold the Power/Scan button for 3s again.
Adjust the Volume
Press the Up button to increase the volume while press the Down button to
decrease the volume. There are total 16 volume levels available. A digital
volume grade on the screen lets you know the details. You can press PTT button
to confirm the setting.
Channel Settings
To guarantee normal performance, make sure both the main channels and
interference eliminator codes of all walkie talkies are the same.
- Press the Menu button for the first time, then you can set the main channel. Press the Up or Down button to select the desi red one and confirm the settings with PTT button. Press the Menu button again to set the interference eliminator codes.
- There are total 121 interference eliminator codes. Press the Up or Down button to choose required one, and press the PTT button on the left side to confirm.
Ringtone Settings
In a power-on state, the 3rd time pressing the Menu button can set the
ringtone. The LCD screen displays a CA symbol and the ringtone code flashes.
There are total 10 different ringtones available. At this time, press the Up
or Down button to choose the ringtone needed and save the settings by pressing
the PTT button.
Sensitivity Settings
A proper sensitivity can help minimize the unintended noises during
conversation. In a power-on state, the 4th time pressing the Menu button can
adjust the sensitivity.
- When the LCD screen displays a symbol, press the Up or Down button to select the desired level and save the settings by pressing the PTT button.
- = low sensitivity (fits for noisy occasions)
- = medium sensitivity (fits for most occasions)
- = high sensitivity (fits for quiet occasions)
Squelch Settings
In a power-on state, the 5th time pressing the Menu button can set the squelch
level. When the LCD screen displays a SL symbol, press the Up or Down button
to choose the one needed and save the settings by pressing the PTT button.
- 1 = high receiver sensitivity
- 2~5 = medium receiver sensitivity
- 6 = low receiver sensitivity
TX Power Settings
- In a power-on state, the 6th time pressing the Menu button can set the transmission power level. When the LCD screen displays a PR symbol, press the Up or Down button to set it as LO or HI and confirm the settings with PTT button.
- TX PR means the setup of tranmission power, generally including high level and low level. Under high transmission power, the walkie talkie outputs the maximum power, the transmission distance is the farthest but it has large power consumption Under low transmission power, the walkie talkie outputs in a low power but you can use them when you are close to your partner(s) to save energy, prolong the service life.
Auxiliary Functions
Timeout Timer
To prevent accidental transmission and save battery life, the walkie talkie is
designed to automatically emit continuous warning tone if you press and hold
PTT button for talking over 60 seconds.
Keypad Lock
To avoid accidentally changing settings, you can press and hold the Menu
/Lock button for 3 seconds or until the Q symbol displays on the screen.
In the keypad locking state, you can still turn on/off the device, transmit or
receive signals, send a ringtone or scan channels. To unlock the keypad, press
and hold the Menu /Lock button again for 3 seconds until the symbol
disappears.
Scanning/Monitoring
This function can monitor transmission channels or find out someone in your
group who has accidentally changed channels. Simply press the Power/Scan
button to scan channels and the . symbol will display on the screen.
The device will automatically stop scanning and you can hear transmission
voice when it detects available channel signals. To respond the transmission,
please press the PTT button within 5 seconds.
VOX Mode
In the off state, press the PTT button and Power button simultaneously until
you see the symbol on the screen. The device enters VOX mode.
Speak to the microphone and the device will automatically transmit your voice. There is a short delay between the time you speak and it transmits. To turn off the VOX function, simply short press the PTT button.
Factory Reset
Please turn off the walkie talkies. Press & Hold ” MENU and Power” button.
Then the device will reset factory default setting.
Troubleshooting
How to ensure that all walkie talkies can communicate smoothly?
- Make sure the main channels and interference eliminator codes bands of all walkie talkies are the same.
- Make sure all walkie talkies are within the transmission distance. It can reach up to 4.8km(3 miles) in absolutely open area. If the surrounding buildings are dense or there is much electromagnetic radiation interference from nearby, it will affect the communication to some extent. Change to another place for better performance.
How to make the battery last longer?
- When the walkie talkie is not in use, please turn off the device.
- If the walkie talkies are close to each other or when there is less interference, switch the TX power setting into LO (take reference of section 4.7)
- Set a more reasonable volume level based on your current surroundings.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>