SUNCO LIGHTING MS-MFD11-40W27V-50K-DKNB77 LED Flood Light Installation Guide

SUNCO LIGHTING MS-MFD11-40W27V-50K-DKNB77 LED Flood Light

Product Information

The LED Flood Light is a weatherproof outdoor lighting fixture designed to provide bright and efficient illumination. It is suitable for various applications such as illuminating driveways, gardens, landscapes, and building facades. The flood light comes with a 1/2 NPS knuckle mount for easy installation and flexibility in positioning. It is recommended to have the installation and service performed by a qualified licensed electrician.

Installation Instructions:

1. Read all instructions carefully before attempting installation.
2. Securely install the fixture by attaching the knuckle bracket to a weatherproof Junction Box (supplied by others) using a 1/2 locknut.
3. Make electrical connections by connecting the supply ground (L/N/GND) lead to the fixture ground (L/N/GND) lead, following the National Electrical Code and all applicable local codes and ordinances.
4. Aim the fixture to the desired tilt angle by loosening the screw on the knuckle of the fitter and rotating the fixture. Re-tighten the screw to secure the position.
5. Ensure that water does not enter the fixture through the 1/2 fitter while making electrical connections.
6. It is essential to seal the 1/2 NPS thread using weatherproof silicone sealant during installation.

Note: The optional ground stake mount can be used instead of the knuckle mount if desired.

Troubleshooting:
Before troubleshooting, always turn off the power.

1. If the light does not come on:
   • Check if the circuit breaker has tripped.
   • Confirm that the wall switch is turned on.
   • Ensure that the wiring to the unit is secure.
   • Check that the line voltage at the fixture is correct.
   • Confirm that the wiring is properly secured.
2. If the light still does not work after checking, contact customer service for further assistance.

WARNING

WARNING – READ ALL INSTRUCTIONS BEFORE ATTEMPTING ! INSTALLATION.

• To prevent personal injury or product damage only licensed electricians should install.
• To avoid electric shock or component damage disconnect power before attempting installation or servicing.
• This product must be installed in accordance with the national electric code (NEC) and all applicable federal, state and local electric codes and safety standards.
• Disconnect product and allow cooling prior to servicing.
• Any alteration or modification of this product is expressly forbidden as it may cause serious personal injury, death, property damage and/or product malfunction.
• To prevent product malfunction and/or electrical shock this product must be properly grounded.
• LIMIT RANGE OF A DJUSTMENT TO.
• Suitable for operation in ambient temperatures ranging from – 40°F + 104°F.
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Min 167°F. supply conductors.
• Suitable for mounting within 1.2 m (4 ft) of the ground
• This product is not available for several special environments, such as places with corrosive gas liquids or high pressure water vapor.

INSTALLATION

1/2″ NPS Knuckle Mount (Optional ground stake mount)

1. Install the fixture by knuckle bracket on the weatherproof Junction Box (supplied by others),and secure it by 1/2″ locknut.
2. Make electrical connections from the supply ground (L/N/GND) lead to fixture ground (L/N/GND) lead respectively, making sure to follow all National Electrical Code and all applicable local codes and ordinances.
3. Aim fixture by loosening screw on knuckle of fitter and rotating fixture to desired tilt angle. Re-tighten screw.
4. While making electrical connections, ensuring water does not enter fixture through 1 /2″ fitter.
5. Installation and service of luminaires should be performed by a qualified licensed electrician.
   CAUTION: Seal the 1/2″ NPS thread using weatherproof silicone sealant while installing. This is especially important.

TROUBLESHOOTING

Turn off power before continuing.

1. Light does not come ON.
   • A. Check if circuit breaker tripped.
   • B. Confirm wall switch is ON.
   • C. Check that if the wiring to the unit is loose.
   • D. Check that the line voltage at the fixture is correct.
   • E. Confirm wiring is properly secured.
     If light still does not work after checking, contact customer service.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>