NETVIO RX-HT2-40-10 HDBaseT PoC Receiver with Ethernet User Guide
- June 4, 2024
- NETVIO
Table of Contents
NETVIO RX-HT2-40-10 HDBaseT PoC Receiver with Ethernet
Quick Start Giulde
Thank you for purchasing this Netvio product. The quick-start-guide is designed to provide all required information to install your product successfully, ensuring correct installation standards, therefore guaranteeing performance in accordance with published features and specifications. Netvio therefore greatly appreciates your time in reviewing the provided information and following our recommended guidelines.
RX-HT2-40-10
4K/60 HDR HDBaseT receiver over single category cable. Capable of sending the latest bandwidth heavy sources over 40m when connected to a compatible matrix device (see specifications for compatibility).
BOX CONTENTS
- Netvio HDBaseT TX & RX Device.
- 2x Wall mount brackets
- 1x Infrared receiver (capture) cables
- 1x Infrared emitter (sender) cables
- 1x 3-way screw termination connectors
WARRANTY INFORMATION
- 2-Year standard parts & labour warranty
- FREE 3-Year warranty subject to product registration.
- 5-Year & 10-Year extended warranty options available.
- Full warranty details including coverage, registration
- warranty extensions available at www.netvio.co.uk
PRODUCT SUPPORT
Please contact your authorised Netvio reseller.
- UK/EMEA Support | +44 (0) 870 488 7001
- US Support | +833 720 0637
- Email |support@netvio.co.uk
- Live Chat |www.netvio.co.uk
Cabal and Connector Guidelines
- Advertised cable distances are there for a guidance. Many factors can effect transmission distances including cable construction, quality, install standards, patch panels, faceplates and external factors such as electrical magnetic interference (EMI).
- This product is designed to run over unshielded twisted pair Cat5e/6/7 cable. Some consideration is required when installing shielded (STP) category cable ensuring all drain wires and shielding materials are correctly grounded
- All RJ45 terminations should follow EIA/TIA-568-B terminations and not simply wired Pin 1-1, Pin 2-2.The 568-B standard involves the splitting of the green pair to pins 3 & 6
- Maintain twists within the Cat5e/Cat6/Cat7 cores up to the point of termination.
- Maintain gradual bends when installing category cable, ensuring a minimum radius of 25mm where possible. Avoid sharp bends or twists in the cable avoiding taught or stretched cable at all times.
- When dressing the cable use moderate to low pressure, avoiding pinching of the cable jacket.
- Do not splice, join or bridge the cable at anytime, as this will undoubtedly cause transmission issues
- Use moderate to low pressure when pulling category cable avoiding pressures in excess of 25 lbs (of force).
- Keep category cable away from sources of EMI (electrical cables, transformers, light fixtures) ensuring a minimum parallel distance of 300mm, crossing at right angles if absolutely necessary.
- Ensure cable is correctly tested, understanding that a basic continuity check may not be sufficient to identify issues or to certify cable performance
- Always check local regulations relating to building and fire codes.
Installation Guidelines
- Please ensure you secure the devices especially at the display location using the brackets provided. Transmission stability will be effected if the product is not probably secured especially if connections are strained.
- The device should be installed against a clean, dry and flat surface. The receiver should be installed vertically with all product logos and descriptions facing you to ensure best airflow and cooling.
- Please ensure the device has adequate ventilation, avoiding any type of enclosure or material that will prevent airflow through the product.
- The receiver draws its power from the connected matrix, therefore local power is not required. Although some functionality will work, it
is not advised to use with other manufacturer products as power-over-cable rating may differ and harm the product.
| Attempts to remove product casings could result in electrical shock. Please
do not attempt to repair the device. In the event of product service
requirements, please contact Netvio Ltd or an authorised reseller for service
procedures. Any unauthorised attempt to repair the product or attempts to
replace components with non-approved parts will invalidate the product
warranty. For full warranty conditions, please visit
www.netvio.co.uk
---|---
Receiver Overview
| Power Status LED
---|---
| Firmware update port
| DC 24V Power In | no local PSU required.
| HDBaseT Input (from display)
| HDMI Output (to display)
| Stereo Audio Output
---|---
| IR Capture Port
| IR Sender Port
| RS-232 Pass Through
IR Pin Outs
Each Netvio receiver comes complete with all required accessories to fully maximise product features and functionality. We recommend the use of Netvio approved IR accessories to ensure guaranteed performance and compatibility. In perfect conditions, IR performance is rated at 8m from display to remote control, but understanding this will vary in differing light conditions. It may be necessary to adjust both the capture, sender device positions to achieve best performance, ensuring that remote batteries are in good condition. Should IR ports require connections to a 3rd party device, the following wiring diagrams are provided to ensure successful signal transfer.
Wiring Schematic
Secure hardwired bi-directional serial control between source and display. Receiver comes complete with 3-Pin screw type connectors for ease of install.
The receiver is powered from the Netvio matrix device over the category cable. A local power supply is not required.
1
|
2
---|---
Solid | Good Connection| Solid | HDMI with HDCP
Flashing | Poor Connection| Flashing | HDMI no HDCP
Dark | No Connection| Dark | No Connection
Basic Specifications
Transmission Distances| 4K/60 HDR @ 40m | 1080p @ 70m
---|---
Encoding Data Rates| HDMI 17.82 Gbp | HDBaseT 10.2Gbs | Visually
lossless compression > 10.Gbs
Video Resolutions (Max)| 3840×2160 60fps HDR over 40m Cat5e/6/7 cable
(1080P @ 70M)
Max Pixel Clock| 600MHz
HDR| HDR10, HDR10+, Hybrid Log-Gamma, Dolby Vision
HDCP| Inclusive up to 2.2
Audio Formats| LPCM 2ch, LPCM 5.1, LPCM 7.1, Dolby Digital, Dolby
Digital Plus, Dolby TrueHD, DTS,
| DTS Master, Dolby Atmos, DTS:X.
CEC| Pass-thru subject to source and display compatibility
Storage| -20°C / +60°C | 20% – 90% RH
Operating| 0°C / 40°C | 20% – 90% RH
Power| 24v PoC power over HDBaseT.
Weight | Dimensions| 160g| H: 20mm | W: 140mm | D: 65mm
Regulations| CE | UKCA | FCC | RoHS
Warranty| 2-Yr Standard, 3-Yr with registration, 5-Yr & 10-Yr extended
warranty available.
Matrix Compatibility| MX-HT2-0404-10 | MX-HT2-0806-10 | MX-HT2-0808-10
---|---
Alternative Receiver Models| RX-HT2-40-20 | Addition of ARC function
| RX-HT2-70-10 | 70m 4K/60 HDR, ARC, Ethernet
Cost effective 5-yr (for 5%) and 10-yr (for 10%) extended warranties available at www.netvio.co.uk/safeguar
Please dispose and recycle responsibly in accordance with local laws and regulations
| Attempts to remove product casings could result in electrical shock. Please
do not attempt to repair the device. In the event of product service
requirements, please contact Netvio Ltd or an authorised reseller for service
procedures. Any unauthorised attempt to repair the product or attempts to
replace components with non-approved parts will invalidate the product
warranty. For full warranty conditions, please visit
www.netvio.co.uk
---|---
Netvio Ltd – INFOLAB21, Lancaster University, Bailrigg Road, Lancaster, LA1 4WA, UK
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>