DAYTON AUDIO SPA1000 1000W Subwoofer Plate Amplifier User Manual
- June 13, 2024
- DAYTON AUDIO
Table of Contents
DAYTON AUDIO SPA1000 1000W Subwoofer Plate Amplifier User Manual
FEATURES
- Patented tracking downconverter power supply for high efficiency
- Class AB output stage for clean, controlled output
- Low frequency parametric EQ allows you to boost or cut to custom-tailor the sound
- Advanced soft clip circuitry improves headroom and protects woofers
- Variable low pass filter
- Dual voltage 120/230V input
INSTALLATION
The SPA1000 is designed to provide high fidelity subwoofer amplification and is tailored for home audio, home theater, and studio environments.
It is not recommended for use in DJ, pro-sound, or other high-duty-cycle
applications. The amplifier runs coolthanks to its high efficiency, but care
should be taken to leave some room for air circulation above and behind the
amplifier.
INPUT CONNECTIONS
-
Left/Right inputs
RCA style jacks that will accept standard line level inputs from a pre-amp level source. They will accept a stereo signaland internally combine it into mono. Both left and right input jacks must be connected to the source in order to drive the amplifier to full output. The use of a “Y” cord is suggested if a mono source is all that is available. -
LFE direct input
RCA jack that will accept a signal from the mono LFE (Low Frequency Effects) output on a pre-amp or receiver that is equipped with a dedicated sub bass output. This input bypasses the amplifier’s own internal low pass filter circuitry, relying instead on the processed output provided by the sourceequipment. This would be the recommended connection for most home theatre surround sound receivers and pre-amps. We would also suggest the use of the LFE input when an external line level electronic crossover or frequency dividing network is used. -
Power input
This unit features an IEC grounding type power input connector. The IEC inlet connector also features an integrated fuse holder that contains the AC line fuse. For 230V input, remove the fuse holder, rotate 180 degrees, and re- install. In most 230V applications a separate power cord and fuse will be required and is not included
CONTROLS/INDICATORS -
Low Pass, Gain
Will match the amplifier’s input sensitivity to the output of the pre-amp source. If the source output has a variable control, we recommend that the user spend a moment or two determining the best balance between the two controls. When a balance is found between low noise, linear level control, and sufficient level to drive the amp to the required output, the gain knob can be considered to be the “volume control” for the subwoofer system. -
Low Pass, Frequency
This control is used to establish the highest frequency that thesubwoofer will reproduce and has a range between 30 and 200 Hz. If your main speakers have good bass capability, you could set the control to a fairly low value at 40, 60, or even 100 Hz. If the main speakers are smaller or do not have much bass output, set the control higher. Experiment with the amount of “overlap” that you will experience when all speakers are playing in the same range. This can be helpful when integrating the subwoofer with the rest of the system and with the room. -
Power Switch
This switch manually turns the unit on and off. When switched to the on position, the unit will first turn on and be fully operational. After a period of 10-15 minutes without a signal the unit will go into “stand by” mode. -
Power LED
When the power switch is moved to the “on” position, the LED will illuminate in dim green, and the amp will be in “stand by” mode. If a low level signal of about 3 millivolts or greater is applied to the input, the light will change bright green to indicate that the amplifier is fully operational and receiving typical music program. As input signal increases to the onset of clipping the LED will turn red, which indicates that the clip limiting circuitry is activated. If an input signal is not detected for 10 to 15 minutes, the amp will go back to “stand by” mode and the LED will change back to dim green. -
Phase
This two-position (NOR = 0° phase and REV = 180° phase) switch helps to compensate for differences in the acoustical and electrical characteristics between the subwoofer and the main system speakers. The relative locations of speakers in the system can cause significant disturbances in speaker interaction due to time delay issues, or the destructive phase interferences that can occur at certain frequencies. The use of this switch in conjunction with altering the location of the subwoofer can have a dramatic effect on system integration. The “NOR” setting would be considered the normal or default setting, but be sure to experiment during system set-up.
PARAMETRIC EQUALIZER
The SPA1000Amplifier features a fully parametric equalizer to help you to achieve the best possible subwoofer performance. Professional sound engineers have for many years considered the parametric EQ to be one of the most accurate, versatile, and high fidelity tools for audio enhancement.Agreater degree of control can be achieved when using the EQ’s unique ability to vary the frequency to be affected, the amount of boost or cut, and the width or narrowness at the selected frequency -
EQ-Frequency
Establishes the specific frequency at which EQ boost or cut may be applied between 18 Hz and 80 Hz. -
EQ-Bandwidth
Determines how narrow or wide the EQ curve will be within a range of 0.1 to 1.0. If for example a frequency of 60 Hz were selected along with a Q of 0.1, the frequencies to either sideof 60 Hz would be less affected. This is a narrow bandwidth that could be useful for “surgically” removing an offending peak without disturbing adjacent frequencies. At the other extreme, a Q of 1 would result in a much broader effect which could be used for smooth overall bass boost or cut, to balance the overall tone character of the sub. -
EQ-Level
Permits the application of up to 6dB of boost or 14.5dB of cut at the selected frequency and bandwidth. Setting the control at the 0 position effectively removes the EQ from the circuit path. It is good to remember that high levels of boost reduce amplifier headroom; it is the same as turning up the low pass gain control but only at the selected EQ frequencies. It would be helpful to reduce or increase the low pass gain control to balance the amount of cut or boost applied by the EQ. -
Output Lead for Subwoofer Driver:
This rear mounted output lead connects the amplifier to the subwoofer driver. The output lead is roughly 20″ long and is color coded. The red wire uses an insulated .250″ quick disconnect and the black wire uses an insulated .205″ quick disconnect. These connectors can be easily removed if your driver requires another size or type of connector. Be sure to observe proper polarity when connecting the amplifier to your subwoofer driver (red = positive, black = negative)
NOTES ABOUT HUM:
While the SPA1000 has been designed to minimize the possibility of hum in the subwoofer system, it is still possible that a hum will occur in rare circumstances. Its safety grounding can create a path for small amounts of 60 Hz energy to travel through the line-level audio system. While not dangerous, this energy can cause diffi culty with the subwoofer auto signal sensing circuit, and at the very least will interfere with the quiet enjoyment of your system. The fi rst course of action should be trying to make sure that all of the audio components are connected to either the same electrical outlet, or at least into the same circuit branch. Next, cable TV systems are notoriously the culprit, so be sure to try disconnecting all coaxial feeds that are connected to the system. If this solves the problem, install a coaxial line isolator and reconnect the system. In the very worst case, a line-level audio isolator/transformer connected to the line-in of the subwoofer amplifi er will usually solve the problem
SPECIFICATIONS
Rated Power Output: (0.92 % THD) 497 Watts into 8 ohms, 950 Watts into
4 ohms
*Based on one-third power duty cycle
Signal to Noise Ratio: 98 dB A-weighted
Effi ciency: 86%
Input Impedance: 12K ohms
Low Pass Adjustment : 30 Hz – 200 Hz
Phase Adjustment: 0° (NOR) or 180° (REV)
Parametric EQ:
Frequency: 18 Hz – 80 Hz
Bandwidth: 0.1 – 1 Q
Level: -14.5dB – +6dB
Dimensions: 11-15/16″ W x 11-15/16″ H x 5-1/4″ D
Enclosure Cutout: 10″ x 10″
Power Requirements : 120/230 VAC, 50 Hz/60 Hz
Stand-by Power Rating: 120V 24W; 230V 18.4W
Weight: 17 lbs
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualifi ed personnel. To reduce the risk of fi re and shock do not expose unit to rain or moisture. The unit should be connected to an earth grounded AC electrical socket. The unit should be operated in a well ventilated area. Minimum clearance is 2 inches from the ventilation opening
CAUTION
** RISK OF ELECTRICAL SHOCK
DO NOT OPEN
AVIS:** RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
Note : Unit is set at the factory for 120V operation. Be sure to change the fuse (5A rating) before switching to 230V operation.
WARNING : Operation of this equipment in a residential environment could cause radio interference.
5-Year Limited Warranty
See daytonaudio.com for details
daytonaudio.com
tel + 937.743.8248
info@daytonaudio.co
http://bitly.com/J5Iu8W?r=qr
705 Pleasant Valley Dr.
Springboro, OH 45066
USA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>