Newland NLS-BS20 Barcode Scanner User Guide

Newland NLS-BS20 Barcode Scanner

Product Information

The BS20 is a ring scanner with Bluetooth 5.0 connectivity, designed to be compatible with mobile phones and tablets. It operates at a frequency of 2402-2480MHz and uses GFSK module type. The maximum RF output power is 1.24dBm.

Product Usage Instructions

1. To power on the BS20, long press the On/Off button for 3 seconds.
2. In manual decoding mode, if there is no operation for 1 minute, the BS20 will automatically enter sleep mode.
3. To force power off the BS20, long press the On/Off button for 8 seconds.
4. When connecting the USB cable, the battery-related LED has priority to show. When disconnecting the USB cable, the Bluetooth-related LED has priority to show.
5. Before setting barcode programming, scan the “Enter Setup” barcode. After setting barcode programming, scan the “Exit Setup” barcode.
6. The BS20 has a Good Read Beep feature that can be turned on or off.
7. The BS20 has a Good Read Vibration feature that can be turned on or off.
8. The BS20 can be set to Bluetooth HID Mode or Bluetooth BLE Mode.
9. To clear Bluetooth pairing information before changing to another host, use the “Clear Bluetooth Pairing” barcode programming option.
10. To enable Terminating Character Suffix and set it to CRLF (0x0D,0x0A), use the corresponding barcode programming option.
11. To set Terminating Character to CR (Carriage Return), use the corresponding barcode programming option.
12. To disable Terminating Character Suffix, use the corresponding barcode programming option.
13. To restore all factory defaults, use the “Restore All Factory Defaults” barcode programming option.

For more information, please visit the Newland AIDC website.
RF warming for Portable device: The BS20 has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

BS20 is a ring scanner with Bluetooth 5.0 ! and compatible with mobile phones and j tablets

Specification

• Operating Frequency:2402-2480MHz
• Module Type:GFSK
• Max. RF Output Power: 1.24dBm
• LED off: Off/ sleep mode
• Red LED on: charging
• Green LED on: full battery
• Red LED flashes slowly: battery is less than 10%
• Blue LED on: battery is more than 10% and Bluetooth connected
• Blue LED flashes: battery is more than 10% and Bluetooth disconnected

CONNECTION

When connecting USB cable, Battery related LED has the priority to show and when disconnecting USB cable, Bluetooth related LED has the priority to show

1. Long press On/Off button for 3s to ; power on
2. BS20 will auto sleep without operating ¡for min in manual decoding mode
3. Long press On/Off button for 8s to ¡forced power off

Barcode Programming

Scan the Enter Setup before barcode setting and scan the Exit Setup after barcode setting

1. Enter / Exit Setup

2. Good Read Beep

3. Good Read Vibration

4. Bluetooth Mode

5. Clear Bluetooth Pairing

6. Clear Bluetooth Pairing

7. Clear Bluetooth pairing information before change to other host

8. Terminating Character Suffix
   Enable Terminating Character Suffix
   Set Terminating Character to CR (Carriage Return)
   Set Terminating Character to CRLF (OxOD,0x0A)
   Disable Terminating Character Suffix

9. Factory Defaults

FCC

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning  the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

More Information

For more information, please visit
http://www.newlandaidc.com/
Manufacture:Fujian Newland Auto-ID Tech. Co.,Ltd. Add: Newland Science & Technology Park, No. 1 Rujiang West Rd, Mawei,Fuzhou, P.R.China

FCC Statement:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

RF warmomg for Portable device:
The device has been evaluated to meet general RF exposure requipment. The device can be use in portable exposure condition without restriction.

References

• Newland AIDC | Barcode Scanner,Mobile Terminal,OEM Scan Engine

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>