HUBBARDTON FORGE 344227 Henry Post Light Instruction Manual

HUBBARDTON FORGE 344227 Henry Post Light

Product Information

• Product Name: Henry Post Light 344227
• Model Number: G24
• Manufacturer: Unknown

Component Parts

• A – Post / Pier Mount (Optional and sold separately)
• B – J Bolt (4) (Included with optional post/pier mount)
• C – Flat Washer (4) (Included with optional post/pier mount)
• D – Split Washer (4) (Included with optional post/pier mount)
• E – Hex Nut (4) (Included with optional post/pier mount)
• F – Cover Cap (Optional and sold separately)
• G – Set Screw
• H – Fixture
• I – Rubber Pad (4)
• J – Glass
• K – Thumb Screws (4)
• L – Metal Shade

Important Safety Instructions

Failure to install this fixture properly may result in serious personal injury or death and property damage. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved. Do not exceed the maximum wattage noted on the fixture. Use only recommended bulbs with the fixture.

Product Usage Instructions

Installation

CAUTION: Be sure power is off at the main breaker box prior to installation. Note that the fixture, post, and  cover cap are sold separately.

Site Preparation

1. Run appropriate wiring to the site of the fixture, leaving enough excess wire to reach the top of the post, plus 12 inches.

2. Pour a flat and level concrete base with wiring emerging at the center.

3. Insert J bolts (B) so approximately 1 of the bolts are exposedabove the concrete. Position J bolts according to the template on the last page of these instructions. Allow the concrete to cure before installing the fixture.
   Installation

4. Position the post (A) over J bolts (B), feeding the supply wire up through the post and secure using flat washers (C), split washers (D), and hex nuts (E).

5. Place the optional cover cap (F) over the post (A) to conceal the mounting hardware.

6. Attach the four rubber pads (I) to the inside of the fixture (H).

7. Connect fixture wires to supply wires using appropriate wire connectors (not provided), black to black (or smooth), white to white (or ribbed), and bare copper or green to bare copper or green. Ensure wire connectors are twisted on securely and no bare wire is exposed.

8. Place the fixture (H) onto the post (A), carefully tucking all wiring down into the post and making sure no wires are pinched between the post and the fixture. Secure with the set screw (G).

9. Follow the steps on the next page to install the glass.

Installation of Glass

1. Unpack the glass (J).
2. Install a bulb (not included) into the socket.
3. Slide the glass (J) over the bulb until it rests on the fixture (H).
4. Remove the thumb screws (K) from the fixture (H).
5. Place the metal shade (L) onto the fixture (H), aligning the holes with the fixture arms.
6. Install the thumb screws (K) to hold the shade (L). For ease of installation, make sure all screws (K) are started before tightening.

Component Parts

NOTE : Items A through F are options sold and shipped separately to allow for various site situations and shown here for reference during installation as applicable

• A Post / Pier Mount – Optional and sold separately
• B J Bolt (4) – Included with optional post/pier mount
• C Flat Washer (4) – Included with optional post/pier mount
• D Split Washer (4) – Included with optional post/pier mount
• E Hex Nut (4) – Included with optional post/pier mount
• F Cover Cap – Optional and sold separately
• G Set Screw
• H Fixture
• I Rubber Pad (4)
• J Glass
• K Thumb Screws (4)
• L Metal Shade

ASSEMBLY & INSTALLATION INSTRUCTIONS

CAUTION : FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution : Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note : After installation extra hardware and accessories are possible; our kits are used on multiple products

To Install (Figure 1)

CAUTION : BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION
NOTE : Fixture, Post and Cover Cap each sold separately

SITE PREPERATION:

1. Run appropriate wiring to the site of the fixture, leaving enough excess wire to reach the top of the post, plus 12 inches.

2. Pour flat and level concrete base with wiring emerging at the center. Insert J bolts (B) so approximately 1″ of the bolts are exposed above the concrete. Position J bolts according to the template on the last page of these instructions. Allow concrete to cure before installing fixture
   INSTALLATION:
   NOTE : Post may be cut to desired height before installation

3. Position post (A) over J bolts (B), feeding supply wire up though the post and secure using flat washers (C), split washers (D) and hex nuts (E).

4. Place optional cover cap (sold separately) (F) over post (A) to conceal mounting hardware.

5. Attach the four rubber pads (I) to the inside of fixture (H).

6. Connect fixture wires to supply wires using appropriate wire connectors (not provided), black to black (or smooth), white to white (or ribbed) and bare copper or green to bare copper or green
   CAUTION : MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY AND NO BARE WIRE IS EXPOSED.

7. Place fixture (H) onto post (A), carefully tucking all wiring down into post and making sure no wires are pinched between the post and the fixture. Secure with set screw (G).

8. Follow steps on next page to install glass

To Install Glass (Figure 2)

1. Unpack glass (J).

2. Install bulb (not included) into socket.

3. Slide glass (J) over bulb until it rest on fixture (H).

4. Remove thumb screws (K) from fixture (H).

5. Place metal shade (L) onto fixture (H), aligning the holes with the fixture arms.

6. Install thumb screws (K) to hold shade (L). For ease of installation, make sure all screws (K) are started before tightening fully.
   NOTE : It may be necessary to flex the fixture arms so all shade holes line up with threaded holes in fixture arms.

7. Restore electricity at main breaker.

USE THIS TEMPLATE TO POSITION J BOLTS AND WIREWAY IN THE CONCRETE SLAB PRIOR TO INSTALLING OUTDOOR POST-MOUNTED LIGHTING FIXTURE

DIMENSION

If you need further assistance or find that you are missing any parts, please get in touch with the dealer from which you purchased this product. We hope you enjoy your fixture!
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>