HUBBARDTON FORGE 342023 Tura Post Light Instruction Manual
- June 13, 2024
- HUBBARDTON FORGE
Table of Contents
HUBBARDTON FORGE 342023 Tura Post Light
Product Information
The Tura Post Light 342023 is a lighting fixture designed for outdoor post mounting. It is manufactured by Hubbardton Forge.
The product consists of the following component parts:
- A J Bolt (optional and sold separately)
- Post (optional and sold separately)
- Flat Washer (optional and sold separately)
- Split Washer (optional and sold separately)
- Hex Nut (optional and sold separately)
- Cover Cap (optional and sold separately)
- Set Screw
- Fixture
- Rubber Pad
- Glass
- Bulb (not included)
- Socket
- Rubber Bumpers
Product Usage Instructions
To install the Tura Post Light, please follow these steps:
- Ensure that the rubber pads (I) fit inside the fixture (H). Trim them if necessary.
- Connect the fixture wires to the supply wires using appropriate wire connectors. Connect black to black (or smooth), white to white (or ribbed), and bare copper or green to bare copper or green. Make sure the wire connectors are twisted on securely and no bare wire is exposed.
- Place the fixture (H) onto the post (B), ensuring that all wiring is tucked down into the post and there are no wires pinched between the post and the fixture. Secure the fixture with the set screw (G).
- Install a bulb (K) (not included) into the socket (L).
- Unpack the glass (J) and carefully place it into the fixture (H), sliding it over the bulb (K) and socket (L).
- Optionally, add rubber bumpers (M) to the fixture (H) to prevent the glass (J) from contacting the fixture cage.
- Restore electricity at the main breaker.
If you need further assistance or find that you are missing any parts, please contact the dealer from which you purchased this product.
Note: Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping, or use of this fixture.
ASSEMBLY
Tura Post Light 342023
Component Parts
NOTE: Items A through F are options sold and shipped separately to allow
for various site situations and shown here for reference during installation
as applicable.
- A J Bolt (4) – Optional and sold separately
- B Post – Optional and sold separately
- C Flat Washer (4) – Optional and sold separately
- D Split Washer (4) – Optional and sold separately
- E Hex Nut (4) – Optional and sold separately
- F Cover Cap – Optional and sold separately
- G Set Screw
- H Fixture
- I Rubber Pad (4)
- J Glass
- K Bulb (Not Included)
- L Socket
- M Rubber Bumpers (8)
INSTALLATION INSTRUCTIONS
- CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
- Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
- Please Note : After installation extra hardware and accessories are possible; our kits are used on multiple products.
To Install (Figures 1 & 2)
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO
INSTALLATION.
NOTE: Fixture, Post and Cover Cap each sold separately.
SITE PREPARATION:
-
Run appropriate wiring to the site of the fixture, leaving enough excess wire to reach the top of the post, plus 12 inches.
-
Pour flat and level concrete base with wiring emerging at the center. Insert J bolts (A) so approximately 1″ of the bolts are exposed above the concrete. Position J bolts according to the template on the last page of these instructions. Allow concrete to cure before installing fixture.
INSTALLATION:
NOTE: Post may be cut to desired height before installation. -
Position post (B) over J bolts (A), feeding supply wire up though the post and secure using flat washers (C), split washers (D) and hex nuts (E).
-
Place optional cover cap (sold separately) (F) over post (B) to conceal mounting hardware.
-
Attach the four rubber pads (I) to the inside of fixture (H).
NOTE: IT MAY BE NECESSARY TO TRIM THE PADS TO FIT INSIDE THE FIXTURE. -
Connect fixture wires to supply wires using appropriate wire connectors (not provided), black to black (or smooth), white to white (or ribbed) and bare copper or green to bare copper or green..
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY AND NO BARE WIRE IS EXPOSED. -
Place fixture (H) onto post (B), carefully tucking all wiring down into post and making sure no wires are pinched between the post and the fixture. Secure with set screw (G).
-
Install bulb (K) (not included) into socket (L).
-
Unpack glass (J) and carefully place glass (J) into fixture (H) sliding over bulb (K) and socket (L).
-
Optionally add rubber bumpers (M) to fixture (H) to prevent glass (J) from contacting the fixture cage.
-
Restore electricity at main breaker.
USE THIS TEMPLATE TO POSITION J BOLTS AND WIREWAY IN CONCRETE SLAB PRIOR TO
INSTALLING OUTDOOR POST MOUNTED LIGHTING FIXTURE.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture!
- Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>