TIKECO P31 15W Wireless Car Charger User Manual

TIKECO P31 15W Wireless Car Charger User Manual

Product Introduction

1. One hand operation, auto clamping when phone placed.
2. Noise-free clamping, phone fastened tight.
3. Wireless charingoutputs: 5W, 7.5W, 10W, 15W. Supportall Qi-enabled mobile phones.
4. The bottom feetis automatically adjusted, which enables accurate alignment for both smalland larger mobile phones, soastoa chive high charging efficiency.
5. Multiple protections: Over-voltage, over-current, over-temperature, over-chargingand FOD.vvvvvvv
6. High efficient wireless charging with good heat disspation.

Attention

1. Inorder toensure the use of experience please choose the brand QC2.0/QC3.0 car charger for this product power supply.
2. Donot open the clamping arms by hand to avoid damaging the gear transmission structure of the unit.
3. Wireless charging efficiency isrelated to carinner temperature.If the temperatureis high, the unit willcome tolimited current chargingmode.
4. Do not disassemble the product by anon-professional.
5. Please keep the product away from fire, water or other liquid.
6. Keep the product away from children

Product Outline

Installation steps

Method 1- Use with air vent

1. Pass the fastening nut through the ball joint of the air vent clip (Pic 1)
   

2. Insert the ball joint into the phone holder (Pic 2)
   

3. Tight the nut (Pic 3)

4. Install it in the air vent of your favorite position (Pic 4)
   

Method 2 – Use with suction cup base

1. Pass the fastening nut through the ball joint of the suction cup base (Pic 5)

2. Insert the ball joint into (Pic 6)
   

3. Adjust the position of the phone holder and suction cup base, and tighten the nut (Pic 7)
   

4. Push the suction cup against a clean area, and press the lock of the suction cup to fix it (Pic 8)
   

5. Adjust the length and angle of the bracket in your favorite position. Adjust the length by pulling the arm after unscrew- inn the knob (do not pull forcibly), and the angle by twisting the bottom knob.(Pic 9)
   

Instructions

1. Power the product via Type C input using a branded QC 2.0/3.0 car charger and a good quality cable (at least 5V/2A)
2. The clamping arms open once the unit is powered. The arms close after phone is placed suitably (refer to below pictures). Now the product is wirelessly charging the phone.
3. Before the car is powered off, press the side button to release your phone. Standard Accessories 15W Wireless Car Charger: 2TYPE C Cable Air Vent Cilp: 4 Fastening Nut, Suction Cup Mount: @User Manual
   

Standard Accessories

1. 15W Wireless Car Charger:
2. TYPE C Cable;
3. Air Vent Cilp:
4. Fastening Nut
5. Suction Cup Mount: User Manual

Product Specification

Input: 9V-2A/12V-1.5A
Output: 15W
(Max) Size: L108 x W74 x H58 mm
Weight: 130g

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class Digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance between 20cm the radiator your body.

IC Caution:

Radio Standards Specification RSS-Gen, issue 5
This device contains licence-exempt transmitter (s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS (s). Operation is subject to the following two conditions:
This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. RF exposure statement:
The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 10cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>