electriQ EIQ-43CVSUWD120FSH 43.4 Inch Curved LED Monitor User Manual

USER MANUAL 43.4 INCH CURVED LED MONITOR
eiQ-43CVSUWD120FSH
eiQ-43CVSUWD120FSHQ

Thank you for choosing electric
Please read the user manual before using this monitor and keep it safe for future reference Visit www.electriQ.co.uk to view our entire range of Intelligent Electricals

SAFETY INFORMATION

• Read these instructions – All the safety and operating instructions should be read before this product is operated.
• Keep these instructions – The safety and operating instructions should be retained for future reference.
• Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.
• Follow all instructions – All operating and usage instructions should be followed.
• Do not use this equipment near water, or in humid environments – The appliance should not be used near water or moisture e.g. in a wet basement or near swimming pool.
• Clean only with a dry cloth. Do not use solvents or petroleum-based fluids.
• Do not block any ventilation openings.
• Do not install near any heat sources such as radiators, stoves or other apparatus (including amplifiers) that produce heat.
• Do not tamper with the supplied plug. This plug is a BS1363 standard plug.
• Protect the power cord from being walked on or trapped, particularly at the plug and at the point where it exits from the appliance.
• Only use attachments/accessories specified by the manufacturer.
• Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart or stand is used, use caution when moving ditto avoid any injuries or damage from it tipping over.
• Unplug the apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as if the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus or it has been exposed to rain or moisture, it does not operate normally or has been dropped.
• Please keep the unit in a well-ventilated environment.
• The monitor should only be connected to a mains power supply as rated on the back of the equipment.
• To prevent overload, do not share the same power supply socket with too many other electronic components.
• Do not place any connecting wires where they may be stepped on or tripped over.
• Do not place heavy items on the cable as this may cause damage.
• When removing from a socket hold by the plug and not the wires.
• Disconnect the power immediately and seek professional help if the plug or cable is damaged, liquid has spilt onto the unit, if accidentally exposed to water or moisture, if anything accidentally penetrates the ventilation slots or if the unit does not work normally.
• Do not remove the safety covers. There are no user serviceable parts inside. Trying to service the unityourse lf is dangerous and may invalidate the product’s warranty. Only qualified personnel should service this apparatus.
• Do not block ventilation slots on the back cover. The monitor can be placed ana cabinet but ensure at least 5cm (2″) clearance all around. Do not tap or shake the screen, this may damage internal components.
• Due to our continuous product development, the operation and or features of the product received may vary slightly from the information provided within the manual.
• WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on the apparatus.
• WARNING: The wall plug socket is used as a disconnection device and should remain readily accessible.
• WARNING: The batteries shall not be exposed to excessive heat such as direct sunlight or fire.
• Although every effort is made to maintain the accuracy of the manual, due to continuous product development, some variation from the manual is possible.
• The availability of features and settings may vary depending on the input source and method of connection.

AT FULL VOLUME, PROLONGED LISTENING MAY DAMAGE THE USER’S HEARING.

| |
---|---|---
This warning sign s to ‘warn of dangerous
voltage inside the product.| CAUTION: To reduce the risk of electric shock, DO NOT remove the cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.| This warning signs to alert you of important
instructions accompanying the product.

PARTS LIST

STAND INSTALLATION

1. Open the package, take out the product out with the protective foam still attached and gently lay it flat on a desk table.
2. Remove the upper foam.
3. Use the 3 X PM5*15 bolts to fasten stem and base.
4. Place the assembled stand onto the back of the monitor. Ensure the stand is securely tightened.
5. Use both hands to stand the assembled monitor on a flat desktop. • Due to the heavy weight and dimensions of the LCD screens and their fragile nature, we recommend that they are unpacked and assembled by 2 people.
   • The stand can be removed from the rear of the monitor by pressing the quick release button on the rear of the monitor.

WALL MOUNT INSTALLATION

1. Open the carton, remove the foam, remove the upper foam.

2. Remove the original bolts x 4 ( 1) from the opening in the back of the monitor. Follow the directions received with your mount, stand, or accessory and install the monitor on the wall or fixture as desired. Remember to use the included bolts when attaching anything to the back of the monitor. Refer to the image (2 ) for correct bolts placement. – Only use the provided bolts for installation
   – keep original Bolts in a safe location for future use.

3. Your monitor is now ready to be attached to a wall-mounting bracket. To avoid damage, please do not pinch the screen during bracket installation.

NOTES:

• Due to the heavy weight and dimensions of the LCD screens and their fragile nature, we recommend that they are unpacked and assembled by 2 people and professional installers are used to wall mount them (Wall mounting is optional). If you do not understand the instructions, or are unsure how to install this product, please contact a professional for assembly advice and assistance.
• Careful consideration should be made regarding the location t he m monitor is to be  wall mounted as some walls are not suitable for installation. If the monitor is to be mounted on drywall, the mount must be anchored into a wooden stud, concrete block or brick behind the drywall. Installing on drywall alone may not support the weight of the display.
• When drilling holes, it is particularly important to take care of electrical cables, water or gas pipes in the wall. Please follow the instructions provided by the wall bracket manufacturer and ensure that all fixing screws supplied are used.
• electric and its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases any guarantee will expire.

CONTROL PANEL

The controls are located centrally at the base of the monitor. Pressing any button when the OSD (On screen display) is not visible will display the Quick Menu

INPUT / OUTPUT TERMINALS

6| Audio Output: Insert one and of the Audio cable into the computer’s Audio output to receive the Audio signals from your monitor.
---|---
7| DP Connector: Insert one end of the DP cable into the computer’s DP output and connect the other end to the monitor’s DP port.
8| HDMI Connector: Insert one end of the HDMI cable into a suitable HDMI source. HDMI output and connect the other end to the monitor’s HDMI port.
9| Power Connector: Insert the power cable to supply power to the monitor

INITIAL SETUP

Connect the monitor to a power outlet.

1. Press the POWER button on the monitor or to turn it on (The indicator will be blue)
2. Connect the relevant cable to the corresponding input on the monitor. The source will be automatically detected.

The main menu for the monitor can be accessed by selecting it within the Quick menu (See previous page). This menu is separated into the following sub menus:
Picture Settings, Image Settings, Colour Temperature, OSD, Reset, and Miscellaneous options, details of each menu can be found in the following sections. Within the Menu:

UP (3) and DOWN (2)| Press to go up and down the current menu or to adjust the selected value.
---|---
MENU (1)| Press to select the currently highlighted item / enter the submenu. Once changes have been made to a value, press to save the changes.
EXIT (4)| Press to navigate to the previous menu. When at the highest level of the Menu, press to close the Menu. After changing a value within the menu, press to cancel the change.

SHORTCUT BUTTONS

The On-Screen Display (OSD) Menu may be used to adjust your monitor’s settings and appears on screen after turning on the monitor and pressing the M button.

1. Press any one of the buttons ( ) to activate the navigation window (Figure 1).

MENU OPTIONS

The menu for the monitor can be accessed by pressing the menu button on the control panel. This menu is separated into the following sub menus: Input source, Brightness/Contrast, Colour Settings, Picture Quality Settings, Display, Audio, Multi-Window, OSD (On screen display), and other. Details of each menu can be found in the following section.

OSD MENU

INPUT SOURCE

Signal Switch the signal input or select the source. DP, HDMI1, HDMI2

COLOUR SETTINGS

FPS and RTS.
Colour Temperature| Change the Colour Temperature of the display to Normal, Warm, Cool or User. When the User Mode is selected, the Red, Green, and Blue values can be adjusted independently between 0 and 100.
Low Blue Light| Change the blue light emitted by the display between0 and 100.
Hue| Change the Hue value between 0 and 100.
Saturation| Change the Saturation of the display between 0 and 100.

PICTURE QUALITY SETTINGS

of low
Noise Reduction| Adjust the level of Noise Reduction between Low, Medium, High, or Off.
Super Resolution| Change the Super Resolution value from 0 to 5.
Dynamic Luminance Control| Turn the Dynamic Luminance Control feature On or Off.

DISPLAY

Aspect Ratio
Change the image aspect ratio to Wide Screen
AUDIO

MULTI-WINDOW

Multi-Window| Choose the different formats of multi window display between Off, Picture in Picture (PIP) and Picture By Picture (PBP 2Win)
---|---
Sub Win2 Input| Choose the source of the second window between HDMI 1 and HDMI 2.
PIP Size| Adjust the size of the secondary source in PIP and PBP modes between Small, Medium and Large
PIP Position| Set the position of the secondary source in PIP and PBP modes between Top Right, Top Left, Bottom Right and Bottom Left.
SWAP| Swap the Primary and Secondary inputs on screen.

OSD

Language| Change the OSD Menu display language between English, Chinese, Korean, Russian, Spanish, Japanese and French.
---|---
OSD H Position| Change the horizontal position of the OSD Menu.
OSD V Position| Change the vertical position of the OSD Menu.
OSD Transparency| Change the transparency value of the OSD Menu between 0 and 100.
OSD Time Out| Change how long the OSD Menu is on before it automatically exits.
OSD Contrast| When the user is the display, this function can also flip the OSD to achieve the best display angle

OTHER

Free Sync Mode| Turn Free Sync On or Off. HDR: Turn HDR On (requires HDMI 2.0 input).
---|---
DP Version| Change the DP version
Reset| Restore factory default setting.
HDR| Turn the HDR on or off.

TECHNICAL SPECIFICATION

Power Supply

Power Consumption

| AC 100-240V~,50/60Hz| AC 100-240V~,50/60Hz
Typical: 68W,Max: 90W| Typical: 68W,Max: 90W
Dimensions(Product Size)| 1060.62562.10286.77mm| 1060.62562.10286.77mm
Net/Gross Weight| 10.2kg / 13.6kg| 10.2kg / 13.6kg
Audio Output Power    (Internal)| 3W| 3W
Picture| Maximum Resolution| 3840 x 1200| 3840 x 1200
Brightness| 380 cd/m 2| 380 cd/m 2
Static Contrast| 3000:1| 3000:1
Response time| 6.9ms (GTG)| 6.9ms (GTG)
Viewing Angle (H/V)| 178°/178°| 178°/178°
Terminals| USB Input| N/A| N/A
HDMI Input| HDMI1.4 x 2, HDMI 2.0 x 1| HDMI1.4 x 2, HDMI 2.0 x 1
Display Port Input| DP1.2 x 1| DP1.2 x 1
Audio Output| x 1| x 1
Speakers| 8Ω3W x 1| 8Ω3W x 1
Working Temperature| 0°C ~40°C| 0°C ~40°C
Working Humidity| 10% ~ 85% Non-condensing| 10% ~ 85% Non-condensing

TROUBLESHOOTING

Ensure the correct input is selected.
Buttons on the monitor don’t do anything| Disconnect the power plug and then reconnect it. (The unit may not be operating properly due to lightning, static, or other factors.)
Noise or other interference| Electronic equipment near the unit may be causing interference. Relocate the unit or move the equipment.

ENVIRONMENTAL PROTECTION

**** Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres

electric UK SUPPORT
www.electriQ.co.uk/support
If the unit fails to operate call: 0871 620 1057 or complete the online form
Office hours: 9AM – 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowveld’s Business Park
Lowveld’s Way, Elland
West Yorkshire, HX5 9DA
https://manual-hub.com/

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>