ASUS Notebook PC

Notebook PC
E-Manual

Notebook PC

Revised Edition V4
August 2015
E10594

COPYRIGHT INFORMATION
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Copyright © 2015 ASUSTeK COMPUTER INC. All Rights Reserved.
LIMITATION OF LIABILITY
Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property; or any other actual and direct damages resulted from omission or failure of performing legal duties under this Warranty Statement, up to the listed contract price of each product.
ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or  infringement under this Warranty Statement.
This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD- PARTY CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.
SERVICE AND SUPPORT
Visit our multi-language web site at http://support.asus.com

About this manual

This manual provides information about the hardware and software features of your Notebook PC, organized through the following chapters:
Chapter 1: Hardware Setup
This chapter details the hardware components of your Notebook PC.
Chapter 2: Using your Notebook PC
This chapter shows you how to use the different parts of your Notebook PC.
Chapter 3: Working with Windows® 10
This chapter provides an overview of using Windows® 10 in your Notebook PC.
Chapter 4: Power-on Self-test (POST)
This chapter shows you how to use POST to change the settings of your Notebook PC.
Chapter 5: Upgrading your Notebook PC
This chapter guides you through the process of replacing and upgrading parts of your Notebook PC.
Tips and FAQs
This section presents some recommended tips, hardware FAQs, and software FAQs you can refer to for maintaining and fixing common issues with your Notebook PC.
Appendices
This section includes notices and safety statements for your Notebook PC.
Conventions used in this manual
To highlight key information in this manual, some text are presented as follows:
IMPORTANT! This message contains vital information that must be followed to complete a task.
NOTE: This message contains additional information and tips that can help complete tasks.
WARNING! This message contains important information that must be followed to keep you safe while performing tasks and prevent damage to your Notebook PC’s data and components.
Icons
The icons below indicate the devices you can use for completing a series of tasks or procedures on your Notebook PC.

| = Use the touchpad.
---|---
| = Use the keyboard.

Typography
Bold = This indicates a menu or an item that must be selected.
Italic = This indicates sections that you can refer to in this manual.

Safety precautions

Using your Notebook PC

| This Notebook PC should only be used in environments with ambient temperatures between 5°C (41°F) and 35°C (95°F).
---|---
| Refer to the rating label on the bottom of your Notebook PC and ensure that your power adapter complies with this rating.
| Do not leave your Notebook PC on your lap or near any part of your body to prevent discomfort or injury from heat exposure.
| Do not use damaged power cords, accessories, and other peripherals with your Notebook PC.
| While powered on, ensure that you do not carry or cover your Notebook PC with any materials that can reduce air circulation.
| Do not place your Notebook PC on uneven or unstable work surfaces.
| You can send your Notebook PC through x-ray machines (used on items placed on conveyor belts), but do not expose them to magnetic detectors and wands.
| Contact your airline provider to learn about related inflight services that can be used and restrictions that must be followed when using your Notebook PC in-flight.

Caring for your Notebook PC

| Disconnect the AC power and remove the battery pack (if applicable) before cleaning your Notebook PC. Use a clean cellulose sponge or chamois cloth dampened with a solution of nonabrasive detergent and a few drops of warm water. Remove any extra moisture from your Notebook PC using a dry cloth.
---|---
| Do not use strong solvents such as thinners, benzene, or other chemicals on or near your Notebook PC.
| Do not place objects on top of your Notebook PC.
| Do not expose your Notebook PC to strong magnetic or electrical fields.
| Do not use or expose your Notebook PC near liquids, rain, or moisture.
| Do not expose your Notebook PC to dusty environments.
| Do not use your Notebook PC near gas leaks.

Proper disposal

Do not throw your Notebook PC in municipal waste. This product has been designed to enable proper reuse of parts and recycling. The symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment and mercurycontaining button cell battery) should not be placed in municipal waste. Check local regulations for disposal of electronic products.
**** Do not throw the battery in municipal waste. The symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.

Chapter 1: Hardware Setup

Getting to know your Notebook PC
Top View
NOTE: The keyboard’s layout may vary per region or country. The top view may also vary in appearance depending on the Notebook PC model.

1. Microphone
   The built-in microphone can be used for video conferencing, voice narrations, or simple audio recording.

2. Camera
   The built-in camera allows you to take pictures or record videos using your Notebook PC.

3. Camera indicator
   The camera indicator lights up when the built-in camera is in use.

4. Microphone (on selected models)
   The built-in microphone can be used for video conferencing, voice narrations, or simple audio recording.

5. Display panel
   This high-definition display panel provides excellent viewing features for photos, videos, and other multimedia files on your Notebook PC.

6. Power button
   Press the power button to turn your Notebook PC on or off. You can also use the power button to put your Notebook PC to sleep or hibernate mode and wake it up from sleep or hibernate mode. In the event that your Notebook PC becomes unresponsive, press and hold the power button for at least four (4) seconds until your Notebook PC shuts down.

7. Numeric keypad (on selected models)
   The numeric keypad toggles between these two functions: for numeric input and as pointer direction keys.
   NOTE: For more details, refer to the Numeric keypad (on selected models) section in this manual.

8. Keyboard
   The keyboard provides full-sized QWERTY keys with a comfortable travel depth for typing. It also enables you to use the function keys, allows quick access to Windows®, and controls other multimedia functions.
   NOTE: The keyboard layout differs by model or territory.

9. Touchpad
   The touchpad allows the use of multi-gestures to navigate onscreen, providing an intuitive user experience. It also simulates the functions of a regular mouse.
   NOTE: For more details, refer to the Using the touchpad section in this manual.

10. Status indicators
    The status indicators help identify the current hardware status of your Notebook PC.

Pwer indicator
The power indicator lights up when the Notebook PC is turned on and blinks slowly when the Notebook PC is in sleep mode.
Two-color battery charge indicator
The two-color LED provides a visual indication of the battery’s charge status. Refer to the following table for details:

power is between 95% and 100%.
Solid Orange| The Notebook PC is plugged to a power source and the battery power is between 95% and 100%.
Blinking Orange| The Notebook PC is running on battery mode and the battery power is less than 10%.
Lights off| The Notebook PC is running on battery mode and the battery power is between 10% to 100%.

Drive activity indicator
This indicator lights up when your Notebook PC is accessing the internal storage drives.
Bluetoth / Wireless indicator
This indicator lights up when your Notebook PC’s wireless function (Bluetooth or Wi-Fi) is enabled.
Number lock indicator (on selected models)
This indicator lights up when the number lock function is activated. This allows you to use some of the keys on your keyboard for numeric input.
Capital lock indicator
This indicator lights up when the capital lock function is activated. Using capital lock allows you to type capitalized letters (such as A, B, C) using your Notebook PC’s keyboard.
Bottom
NOTE: The bottom side may vary in appearance depending on model.
WARNING!

•  The bottom of the Notebook PC can get warm to hot while in use or while charging the battery pack. When working on your Notebook PC, do not place it on surfaces that can block the vents.
• Only ASUS-authorized technicians should remove the battery inside the device.

IMPORTANT! Battery time varies by usage and by the specifications for this Notebook PC. The battery pack cannot be disassembled.

1. Battery pack
   The battery pack is automatically charged when your Notebook PC is connected to a power source. When charged, the battery pack supplies power to your Notebook PC.

2. Spring battery lock (on selected models)
   The spring battery lock automatically locks the battery pack in place once it is inserted into the battery slot.
   IMPORTANT! This lock should be held in an unlocked position when removing the battery pack.

3. Manual battery lock (on selected models)
   The manual battery lock is used to keep the battery pack secured. This lock should be manually moved to a locked or unlocked position to insert or remove the battery pack.

4. Air vents
   The air vents allow cool air to enter and warm air to exit the Notebook PC.
   WARNING! Ensure that paper, books, clothing, cables, or other objects do not block any of the air vents or else overheating may occur.

5. Hard disk drive compartment (on selected models)
   This compartment is a reserved space for the HDD (hard disk drive) of your Notebook PC.

6. Random-access memory module compartment (on selected models)
   This compartment allows you to add RAM (random-access memory) modules to increase the memory capacity of your Notebook PC.

Right Side
15” and 14″ model

1. USB 2.0 port (on selected models)
   The USB (Universal Serial Bus) port is compatible with USB 2.0 or USB 1.1 devices such as keyboards, pointing devices, flash disk drives, external HDDs, speakers, cameras and printers.

2. Optical drive
   Your Notebook PC’s optical drive may support several disc formats such as CDs, DVDs, recordable discs, or rewritable discs.

3. Optical disc drive eject button
   Press this button to eject the optical drive tray.

4. Optical disc drive manual eject hole
   The manual eject hole is used to eject the drive tray in case the electronic eject button does not work.
   WARNING! Use the manual eject hole only when the electronic eject button does not work.
   NOTE: For more details, refer to the Using the optical drive section in this manual.

5. Kensington® security slot
   The Kensington® security slot allows you to secure your Notebook PC using Kensington® compatible Notebook PC security products.

Left Side
15” and 14″ model

1. Power (DC) input port
   Insert the bundled power adapter into this port to charge the battery pack and supply power to your Notebook PC.
   WARNING! The adapter may become warm to hot while in use. Do not cover the adapter and keep it away from your body while it is connected to a power source.
   IMPORTANT! Use only the bundled power adapter to charge the battery pack and supply power to your Notebook PC.

2. Air vents
   The air vents allow cool air to enter and warm air to exit the Notebook PC.
   WARNING! Ensure that paper, books, clothing, cables, or other objects do not block any of the air vents or else overheating may occur.

3. VGA port
   This port allows you to connect your Notebook PC to an external display.

4. HDMI port
   This port is for the HDMI (High-Definition Multimedia Interface) connector and is HDCP compliant for HD DVD, Blu-ray, and other protected content playback.

5. LAN port
   Insert the network cable into this port to connect to a local area network.

6. USB 3.0 port
   The USB 3.0 (Universal Serial Bus 3.0) port provides a transfer rate up to 5 Gbit/s and is backward compatible to USB 2.0.

7. Headphone outputjack/microphone input combo port
   This port allows you to connect your tablet to amplified speakers or headphones. You can also use this port to connect your tablet to an external microphone.
   NOTE: This port does not support three-conductor 3.5mm microphone.

Front Side
NOTE: The front side may vary in appearance depending on model.

1. Status indicators
   The status indicators help identify the current hardware status of your Notebook PC.

2. Memory card reader
   This built-in memory card reader supports SD and SDHC card formats.

Chapter 2: Using your Notebook PC

Getting started
NOTE: If your Notebook PC does not have its battery pack installed, use the following procedures for installation.
Install the battery pack (on selected models)
A. Move the manual battery lock to the unlocked position.
B. Align and insert the battery pack into the Notebook PC’s battery slot.
C. Move the manual battery lock back to the locked position after inserting the battery pack. Charge your Notebook PC
A. Connect the AC power cord to the AC/DC adapter.
B. Plug the AC power adapter into a 100V~240V power source.
C. Connect the DC power connector into your Notebook PC’s power (DC) input.
Charge the Notebook PC for 3 hours before using it in battery mode for the first time.
NOTE: The power adapter may vary in appearance, depending on models and your region. IMPORTANT!

• Locate the input/output rating label on your Notebook PC and ensure that it matches the input/output rating information on your power adapter. Some Notebook PC models may have multiple rating output currents based on the available SKU.
• Ensure that your Notebook PC is connected to the power adapter before turning it on for the first time. We strongly recommend that you use a grounded wall socket while using your Notebook PC on power adapter mode.
• The socket outlet must be easily accessible and near your Notebook PC.
• To disconnect your Notebook PC from its main power supply, unplug your Notebook PC from the power socket.

WARNING!
Read the following precautions for your Notebook PC’s battery.

• The battery used in this device may present a risk of fire or chemical burn if removed or disassembled.
• Follow the warning labels for your personal safety.
• Risk of explosion if battery is replaced by an incorrect type.
• Do not dispose of in fire.
• Never attempt to short-circuit your Notebook PC’s battery.
• Never attempt to disassemble and reassemble the battery.
• Discontinue usage if leakage is found.
• The battery and its components must be recycled or disposed of properly.
• Keep the battery and other small components away from children.

Lift to open the display panel Press the power button

Using the touchpad
Moving the pointer
You can tap anywhere on the touchpad to activate its pointer, then slide your finger on the touchpad to move the pointer onscreen.
Slide horizontally Slide vertically Slide diagonally One-finger gestures
Tap/Double-tap

• Tap an app to select it.
• Double-tap an app to launch it.

Drag and drop Double-tap an item, then slide the same finger without lifting it off the touchpad. To drop the item to its new location, lift your finger from the touchpad.

| ![ASUS Notebook PC

• assembly 30](https://manuals.plus/wp-content/uploads/2023/10/ASUS-Notebook- PC-assembly-30.jpg)
  • Click an app to select it.
  • Double-click an app to launch it.| Click this button to open the rightclick menu.

NOTE: The areas inside the dotted line represent the locations of the left mouse button and the right mouse button on the touchpad.
Two-finger gestures

Two-finger scroll (up/down)| | Slide two fingers to scroll up or down.
---|---|---
Two-finger scroll (left/right)| | Slide two fingers to scroll up or down.
Zoom out| | Bring together your two fingers on the touchpad.
Zoom in| | Spread apart your two fingers on the touchpad.
Drag and drop| | Select an item then press and hold the left button. Using your other finger, slide on the touchpad to drag the item, lift your finger off the button to drop the item.

Using the keyboard

Function keys
The function keys on your Notebook PC’s keyboard can trigger the following commands:

| Puts the Notebook PC into Sleep mode
---|---
| Turns Airplane mode on or off
NOTE: When enabled, the Airplane mode disables all wireless connectivity.
| Decreases display brightness
| Increases display brightness
| Turns the display panel off
| Toggles the display mode
NOTE: Ensure that the second display is connected to your Notebook PC.
| Enables or disables the touchpad
| Turns the speaker on or off
| Turns the speaker volume down
| Turns the speaker volume up

Windows® 10 keys
There are two special Windows® keys on your Notebook PC’s keyboard used as below:

| Press this key to launch the Start menu
---|---
| Press this key to simulate the right-click functions

Multimedia control keys
The multimedia control keys allow you to control multimedia files, such as audios and videos, when played in your Notebook PC.
Press in combination with the arrow keys on your Notebook PC, illustrated as below. Using the numeric keypad
NOTE: The numeric keypad layout may differ by model or territory but the usage procedures remain the same.A numeric keypad is available on selected Notebook PC models. You can use this keypad for numeric input or as pointer direction keys.
Press to toggle between using the keypad as number keys or as pointer direction keys.

Using the optical drive
NOTE:

• The actual location of the electronic eject button may vary depending on your Notebook PC model.
• The actual appearance of the Notebook PC optical drive may also vary depending on model but usage procedures remain the same.
• The optical drive is available on selected models.

Inserting an optical disc

1. While the Notebook PC is on, press the electronic eject button to partially eject the optical drive tray.

2. Gently pull out the drive tray.
   IMPORTANT! Be careful not to touch the optical drive lens. Ensure that there are no objects that may get jammed under the drive tray.

3. Hold the disc by the edge with its printed side up, then gently place it inside the hub

4. Push down the disc’s plastic hub until it snaps onto the optical drive hub.

5. Push the drive tray gently to close the optical drive.
   NOTE: While data is being read, it is normal to hear some spinning and vibrating in the optical drive.

Using the manual eject hole
The manual eject hole is located on the optical drive door and is used to eject the optical drive tray in case the electronic eject button does not work.
To manually eject the optical drive tray, insert a straightened paper clip into the manual eject hole until the drive tray opens.
WARNING! Use the manual eject hole only when the electronic eject button does not work.

Chapter 3: Working with Windows® 10

Starting for the first time
When you start your Notebook PC for the first time, a series of screens appear to guide you in configuring your Windows® 10 operating system.
To start your Notebook PC for the first time:

1. Press the power button on your Notebook PC. Wait for a few minutes until the setup screen appears.

2. From the setup screen, pick your region and a language to use on your Notebook PC.

3. Carefully read the License Terms. Select I accept.

4. Follow the onscreen instructions to configure the following basic items:
   • Personalize
   • Get online
   • Settings
   • Your account

5. After configuring the basic items, Windows® 10 proceeds to install your apps and preferred settings. Ensure that your Notebook PC is kept powered on during the setup process.

6. Once the setup process is complete, the Desktop appears.
   NOTE: The screenshots in this chapter are for reference only.

Start menu
The Start menu is the main gateway to your Notebook PC’s programs, Windows® apps, folders, and settings. You can use the Start menu to do these common activities:

• Start programs or Windows® apps
• Open commonly used programs or Windows® apps
• Adjust Notebook PC settings
• Get help with the Windows operating system
• Turn off your Notebook PC
• Log off from Windows or switch to a different user account

Launching the Start menu
Position your mouse pointer over the Start button in the lower-left corner of your desktop then click it.
Press the Windows logo key on your keyboard.

Opening programs from the Start menu
One of the most common uses of the Start menu is opening programs installed on your Notebook PC.
Position your mouse pointer over the program then click to launch it.
Use the arrow keys to browse through the programs. Press to launch it.
NOTE: Select All apps at the bottom of the left pane to display a full list of programs and folders on your Notebook PC in alphabetical order.

Windows® apps
These are apps pinned on the right pane of the Start menu and displayed in tiled-format for easy access.
NOTE: Some Windows® apps require signing in to your Microsoft account before they are fully launched. Working with Windows® apps
Use your Notebook PC’s touchpad or keyboard to launch, customize, and close apps.
Launching Windows® apps from the Start menu

Position your mouse pointer over the app then click to launch it.
Use the arrow keys to browse through the apps. Press to launch an app.

Customizing Windows® apps
You can move, resize, unpin, or pin apps to the taskbar from the Start menu using the following steps:
Moving apps
Position your mouse pointer over the app, then drag and drop the app to a new location.
Resizing apps
Position your mouse pointer over the app and right-click it, then click Resize and select an app tile size.
Use the arrow keys to navigate to the app. Press , then select Resize and select an app tile size.

Unpinning apps
Position your mouse pointer over the app and right-click it, then click Unpin from Start.
Use the arrow keys to navigate to the app. Press , then select Unpin from Start.

Pinning apps to the taskbar
Position your mouse pointer over the app and right-click it, then click Pin to taskbar.
Use the arrow keys to navigate to the app. Press ,then select Pin to taskbar.
Pinning more apps to the Start menu
From All apps, position your mouse pointer over the app you want to add to the Start menu and right-click it, then click Pin to Start.
From All apps, press on the app that you want to add to the Start menu, then select Pin to Start.

Task view
Quickly switch between opened apps and programs using the task view feature, you can also use task view to switch between desktops. Launching task view
Position your mouse pointer over the icon on the taskbar and click it.
Press on your keyboard.
Snap feature
The Snap feature displays apps side-by-side, allowing you to work or switch between apps. Snap hotspots
You can drag and drop apps to these hotspots to snap them into place. Using Snap

1. Launch the app you wish to snap.

2. Drag the title bar of your app and drop the app to the edge of the screen to snap.

3. Launch another app and repeat the above steps to snap another app.

4. Launch the app you wish to snap.

5. Press and hold the key, then use the arrow keys to snap the app.

6. Launch another app and repeat the above steps to snap another app.

Action Center
Action Center consolidates notifications from apps and presents a single place where you can interact with them. It also has a really useful Quick Actions section at the bottom. Launching Action Center
Position your mouse pointer over the icon on the taskbar and click it.
Press on your keyboard.

Other keyboard shortcuts
Using the keyboard, you can also use the following shortcuts to help you launch applications and navigate Windows® 10.

| Launches Start menu
---|---
| Launches Action Center
| Launches the desktop
| Launches the File Explorer
| Opens the Share panel
| Launches Settings
| Launches Connect panel
| Activates the Lock screen
| Minimizes all currently active windows
| Launches Search
| Launches Project panel
| Opens the Run window
| Opens Ease of Access Center
| Opens the context menu of the Start button
| Launches the magnifier icon and zooms in your screen
| Zooms out your screen
| Opens Narrator Settings

Connecting to wireless networks
Wi-Fi
Access emails, surf the Internet, and share applications via social networking sites using your Notebook PC’s Wi-Fi connection.
IMPORTANT! Airplane mode disables this feature. Ensure that Airplane mode is turned off before enabling the Wi-Fi connection of your Notebook PC.
Connecting Wi-Fi
Connect your Notebook PC to a Wi-Fi network by using the following steps:

1. Select the icon from the taskbar.
2. Select the icon to enable Wi-Fi.
3. Select an access point from the list of available Wi-Fi connections.
4. Select Connect to start the network connection.

NOTE: You may be prompted to enter a security key to activate the Wi-Fi connection.
Bluetooth
Use Bluetooth to facilitate wireless data transfers with other Bluetoothenabled devices.
IMPORTANT! Airplane mode disables this feature. Ensure that Airplane mode is turned off before enabling the Bluetooth connection of your Notebook PC.
Pairing with other Bluetooth-enabled devices
You need to pair your Notebook PC with other Bluetooth-enabled devices to enable data transfers. Connect your devices by using the following steps:

1. Launch Settings from the Start menu.
2. Select Devices, then select Bluetooth to search for Bluetooth-enabled devices.
3. Select a device from the list. Compare the passcode on your Notebook PC with the passcode sent to your chosen device. If they are the same, select Yes to successfully pair your Notebook PC with the device.

NOTE: For some Bluetooth-enabled devices, you may be prompted to key in the passcode of your Notebook PC.
Airplane mode
Airplane mode disables wireless communication, allowing you to use your Notebook PC safely while in-flight.
Turning Airplane mode on
NOTE: Contact your airline provider to learn about related in-flight services that can be used and restrictions that must be followed when using your Notebook PC in-flight.

1. Launch Action Center from the taskbar.
2. Select the icon to enable Airplane mode.
   Press .

Turning Airplane mode off

1. Launch Action Center from the taskbar.
2. Select the icon to disable Airplane mode.
   Press .

Connecting to wired networks
You can also connect to wired networks, such as local area networks and broadband Internet connection, using your Notebook PC’s LAN port.
NOTE: Contact your Internet Service Provider (ISP) for details or your network administrator for assistance in setting up your Internet connection.
To configure your settings, refer to the following procedures.
IMPORTANT! Ensure that a network cable is connected between your Notebook PC’s LAN port and a local area network before performing the following actions.
Configuring a dynamic IP/PPPoE network connection

1. Launch Settings.

2. Select Network & Internet.

3. Select Ethernet > Network and Sharing Center.

4. Select your LAN then select Properties.

5. Select Internet Protocol Version 4(TCP/IPv4) then select Properties.

6. Select Obtain an IP address automatically then select OK.
   NOTE: Proceed to the next steps if you are using PPPoE connection.

7. Return to the Network and Sharing Center window then select Set up a new connection or network.

8. Select Connect to the Internet then select Next.

9. Select Broadband (PPPoE).

10. Type your User name, Password, and Connection name then select Connect.

11. Select Close to finish the configuration.

12. Select on the taskbar then select the connection you just created.

13. Type your user name and password then select
    Connect to start connecting to the Internet.

Configuring a static IP network connection

1. Repeat steps 1 to 5 under Configuring a dynamic IP/PPPoE network connection.
2. Select Use the following IP address.
3. Type the IP address, Subnet mask and Default gateway from your service provider.
4. If needed, you can also type the preferred DNS server address and alternate DNS server address then select OK.

Turning your Notebook PC off
You can turn off your Notebook PC by doing either of the following procedures:

• Launch the Start menu, then select > Shut down to do a normal shutdown.
• From the log-in screen, select > Shut down.
• Press to launch Shut Down Windows. Select Shut Down from the dropdown list then select OK.
• If your Notebook PC is unresponsive, press and hold the power button for at least four (4) seconds until your Notebook PC turns off.

Putting your Notebook PC to sleep
To put your Notebook PC to Sleep mode:

• Launch the Start menu, then select > Sleep to put your Notebook PC to sleep.
• From the log-in screen, select > Sleep.

Press to launch Shut Down Windows. Select Sleep from the drop-down list then select OK.

NOTE: You can also put your Notebook PC to Sleep mode by pressing the power button once.

Chapter 4: Power-on Self Test (POST)

The Power-on Self Test (POST)
The POST (Power-on Self Test) is a series of software-controlled diagnostic tests that run when you turn on or restart your Notebook PC. The software that controls the POST is installed as a permanent part of the Notebook PC’s architecture.
Using POST to access BIOS and Troubleshoot
During POST, you can access the BIOS settings or run troubleshooting options using the function keys of your Notebook PC. You may refer to the following information for more details.
BIOS
The BIOS (Basic Input and Output System) stores system hardware settings that are needed for system startup in the Notebook PC. The default BIOS settings apply to most conditions of your Notebook PC. Do not change the default BIOS settings except in the following circumstances:

• An error message appears onscreen during system bootup and requests you to run the BIOS Setup.
• You have installed a new system component that requires further BIOS settings or updates.

WARNING: Using inappropriate BIOS settings may result to system instability or boot failure. We strongly recommend that you change the BIOS settings only with the help of a trained service personnel.
Accessing BIOS
Restart your Notebook PC then press during POST.

BIOS Settings
NOTE: The BIOS screens in this section are for reference only. The actual screens may differ by model and territory.
Boot
This menu allows you to set your boot option priorities. You may refer to the following procedures when setting your boot priority.

1. On the Boot screen, select Boot Option #1.
2. Press and select a device as the Boot Option #1.

Security
This menu allows you to set up the administrator and user password of your Notebook PC. It also allows you to control the access to your Notebook PC’s hard disk drive, input/output (I/O) interface, and USB interface.
NOTE:

• If you install a User Password, you will be prompted to input this before entering your Notebook PC’s operating system.
• If you install an Administrator Password, you will be prompted to input this before entering BIOS.

To set the password:

1. On the Security screen, select Administrator Password or User Password.
2. Type in a password then press .
3. Re-type to confirm the password then press .

To clear the password:

1. On the Security screen, select Administrator Password or User Password.
2. Type in the current password then press .
3. Leave the Create New Password field blank then press ****.
4. Select Yes in the confirmation box then press ****.

I/O Interface Security
In the Security menu, you can access I/O Interface Security to lock or unlock some interface functions of your Notebook PC.To lock an interface:

1. On the Security screen, select I/O Interface Security.
2. Select an interface you would like to lock then press .
3. Select Lock.

USB Interface Security
Through the I/O Interface Security menu, you can also access USB Interface Security to lock or unlock ports and devices. To lock the USB interface:

1. On the Security screen, select I/O Interface Security > USB Interface Security.
2. Select an interface that you would like to lock then select Lock.

NOTE: Setting the USB Interface to Lock also locks and hides the External Ports and other devices included under USB Interface Security.

Set Master Password
In the Security menu, you can use Set Master Password to set up a password- enabled access to your hard disk drive. To set the HDD password:

1. On the Security screen, select Set Master Password.
2. Type in a password then press .
3. Re-type to confirm the password then press .
4. Select Set User Password then repeat the previous steps to set up the user password.

Save & Exit
To keep your configuration settings, select Save Changes and Exit before exiting the BIOS. To update the BIOS:

1. Verify the Notebook PC’s exact model then download the latest BIOS file for your model from the ASUS website.
2. Save a copy of the downloaded BIOS file to a flash disk drive.
3. Connect your flash disk drive to your Notebook PC.
4. Restart your Notebook PC then press during POST.
5. From the BIOS menu, Select Advanced > Start Easy Flash, then press .
6. Locate your downloaded BIOS file in the flash disk drive then press .
7. After the BIOS update process, select Exit > Restore Defaults to restore the system to its default settings.

Recovering your system
Using recovery options on your Notebook PC allows you to restore the system to its original state or simply refresh its settings to help improve performance.

IMPORTANT!

• Backup all your data files before doing any recovery option on your Notebook PC.
• Note down important customized settings such as network settings, user names, and passwords to avoid data loss.
• Ensure that your Notebook PC is plugged in to a power source before resetting your system.

Windows® 10 allows you to do any of the following recovery options:

• Keep my files – This option allows you refresh your Notebook PC without affecting personal files (photos, music, videos, documents).
  Using this option, you can restore your Notebook PC to its default settings and delete other installed apps.

• Remove everything – This option resets your Notebook PC to its factory settings. You must backup your data before doing this option.

• Go back to an earlier build – This option allows you to go back to an earlier build. Use this option if this build is not working for you.

• Advanced startup – Using this option allows you to perform other advanced recovery options on your Notebook PC such as:
  – Using a USB drive, network connection or Windows recovery DVD to startup your Notebook PC.
  – Using Troubleshoot to enable any of these advanced recovery options: System Restore, System Image Recovery, Startup Repair, Command Prompt, UEFI Firmware Settings, and Startup Settings.

Performing a recovery option
Refer to the following steps if you want to access and use any of the available recovery options for your Notebook PC.

1. Launch Settings and select Update and security.
2. Under the Update and security option, select Recovery then select the recovery option you would like to perform.

Chapter 5: Upgrading your Notebook PC

Installing a Random-access Memory module (on selected models)

Upgrade the memory capacity of your Notebook PC by installing a RAM (random- access memory module) in the memory module compartment. The following steps show you how to install a RAM module into your Notebook PC:
WARNING! Disconnect all the connected peripherals, any telephone or telecommunication lines and power connector (such as external power supply, battery pack, etc.) before removing the compartment cover.
IMPORTANT! Visit an authorized service center or retailer for information on RAM module upgrades for your Notebook PC. Purchase RAM modules from authorized retailers of this Notebook PC to ensure maximum compatibility and reliability.
NOTE: The appearance of your Notebook PC’s bottom side and RAM module may vary per model but the RAM module installation remains the same.
A. Loosen the screw of the Notebook PC’s compartment cover.
B. Pull out the compartment cover and remove it completely from your Notebook PC.C. Align and insert the RAM module into the RAM module slot.
D. Push down the RAM module until it clicks in place.E. Align then push down the compartment cover back into place.
F. Reattach and tighten the screw that you removed earlier.![ASUS Notebook PC

• assembly 61](https://manuals.plus/wp-content/uploads/2023/10/ASUS-Notebook- PC-assembly-61.jpg) Replacing the Hard Disk Drive (on selected models)
  Refer to the following steps if you need to replace the HDD (hard disk drive) of your Notebook PC.
  IMPORTANT! Purchase an HDD from authorized retailers of this Notebook PC to ensure maximum compatibility and reliability. It is recommended that you replace the HDD under professional supervision. You may also visit an authorized service center for further assistance.
  WARNING! Disconnect all the connected peripherals, any telephone or telecommunication lines and power connector (such as external power supply, battery pack, etc.) before removing the compartment cover.
  NOTE: The appearance of your Notebook PC’s bottom side and HDD may vary per model but the HDD installation remains the same.
  A. Loosen the screw of the Notebook PC’s compartment cover.
  B. Pull out the compartment cover and remove it completely from your Notebook PC.C. Remove the screws securing the HDD bay to the compartment.
  D. Disconnect the HDD bay from the HDD port then remove the HDD bay from the compartment.E. Turn the HDD bay upside down then remove the screws.
  F. Remove the old HDD from the HDD bay.G. Place the new HDD with its PCB (printed circuit board) facing the HDD bay. Ensure that the port connectors of your HDD are not obstructed by any part of the HDD bay.
  H. Reattach and secure the HDD with the screws you removed earlier.I. Replace the HDD bay back in the compartment, with the HDD connector aligned with the Notebook PC’s HDD port. Push the HDD bay until it connects with the Notebook PC.
  J. Secure the HDD bay with the screws you removed earlier.K. Align then push down the compartment cover back into place.
  L. Reattach and tighten the screw that you removed earlier.![ASUS Notebook PC
• assembly 67](https://manuals.plus/wp-content/uploads/2023/10/ASUS-Notebook- PC-assembly-67.jpg) Installing a new battery pack (on selected models)
  WARNING! Turn off your Notebook PC and disconnect all connected peripherals, any telephone or telecommunication lines and power connector, before removing the battery pack.
  IMPORTANT! Purchase battery packs from authorized retailers of this Notebook PC to ensure maximum compatibility and reliability.
  NOTE: The following steps are also applicable for removing and replacing the battery pack of your Notebook PC.
  Refer to the following steps when installing a new battery pack for your Notebook PC.
  A. Move the manual battery lock to the unlocked position.
  B. Move and hold the spring battery lock to an unlocked position.
  C. Pull out the old battery pack from the battery slot then release your hold on the spring battery lock.D. Move the manual battery lock to the unlocked position.
  E. Align and insert the new battery pack into the Notebook PC’s battery slot.
  F. Move the manual battery lock back to the locked position after inserting the battery pack.

Appendices

DVD-ROM Drive Information (on selected models)
The DVD-ROM drive allows you to view and create your own CDs and DVDs. You can purchase an optional DVD viewer software to view DVD titles.
Regional Playback Information
Playback of DVD movie titles involves decoding MPEG2 video, digital AC3 audio and decryption of CSS protected content. CSS (sometimes called copy guard) is the name given to the content protection scheme adopted by the motion picture industry to satisfy a need to protect against unlawful content duplication.
Although the design rules imposed on CSS licensors are many, one rule that is most relevant is playback restrictions on regionalized content. In order to facilitate geographically staggered movie releases, DVD video titles are released for specific geographic regions as defined in “Region Definitions” below. Copyright laws require that all DVD movies be limited to a particular region (usually coded to the region at which it is sold). While DVD movie content may be released for multiple regions, CSS design rules require that any system capable of playing CSS encrypted content must only be capable of playing one region.
IMPORTANT! The region setting may be changed up to five times using the viewer software, then it can only play DVD movies for the last region setting. Changing the region code after that will require factory resetting which is not covered by warranty. If resetting is desired, shipping and resetting costs will be at the expense of the user.
Region Definitions
Region 1
Canada, US, US Territories
Region 2
Czech, Egypt, Finland, France, Germany, Gulf States, Hungary, Iceland, Iran, Iraq, Ireland, Italy, Japan, Netherlands, Norway, Poland, Portugal, Saudi Arabia, Scotland, South Africa, Spain, Sweden, Switzerland, Syria, Turkey, UK, Greece, Former Yugoslav Republics, Slovakia
Region 3
Burma, Indonesia, South Korea, Malaysia, Philippines, Singapore, Taiwan, Thailand, Vietnam
Region 4
Australia, Caribbean (Except US Territories), Central America, New Zealand, Pacific  Islands, South America
Region 5
CIS, India, Pakistan, Rest of Africa, Russia, North Korea
Region 6
China
Blu-ray ROM Drive Information (on selected models)
The Blu-ray ROM Drive allows you to view high definition (HD) videos and other disc file formats such as DVDs and CDs.
Region Definitions
Region A
North, Central and South American countries, and their territories; Taiwan, Hong Kong, Macao, Japan, Korea (South and North), South East Asian countries and their territories.
Region B
European, African, and South West Asian countries and their territories; Australia and New Zealand.
Region C
Central, South Asian, Eastern European countries and their territories; China and Mongolia.
NOTE: Refer to Blu-ray Disc website at www.blu- raydisc.com/en/Technical/FAQs/BlurayDiscforVideo.aspx for more details.
Internal Modem Compliancy
The Notebook PC with internal modem model complies with JATE (Japan), FCC (US, Canada, Korea, Taiwan), and CTR21. The internal modem has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN). However due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems you should contact your equipment supplier in the first instance.

Overview

On 4th August 1998 the European Council Decision regarding the CTR 21 has been published in the Official Journal of the EC. The CTR 21 applies to all non voice terminal equipment with DTMF-dialling which is intended to be connected to the analogue PSTN (Public Switched Telephone Network).
CTR 21 (Common Technical Regulation) for the attachment requirements for connection to the analogue public switched telephone networks of terminal equipment (excluding terminal equipment supporting the voice telephony justified case service) in which network addressing, if provided, is by means of dual tone multifrequency signalling.
Network Compatibility Declaration
Statement to be made by the manufacturer to the Notified Body and the vendor:
“This declaration will indicate the networks with which the equipment is designed to work and any notified networks with which the equipment may have interworking difficulties.”
Statement to be made by the manufacturer to the user: “This declaration will indicate the networks with which the equipment is designed to work and any notified networks with which the equipment may have inter-working difficulties. The manufacturer shall also associate a statement to make it clear where network compatibility is dependent on physical and software switch settings. It will also advise the user to contact the vendor if it is desired to use the equipment on another network.”
Up to now the Notified Body of CETECOM issued several pan-European approvals using CTR 21. The results are Europe’s first modems which do not require regulatory approvals in each individual European country.
Non-Voice Equipment
Answering machines and loud-speaking telephones can be eligible as well as modems, fax machines, auto-dialers and alarm systems. Equipment in which the end-to-end quality of speech is controlled by regulations (e.g. handset telephones and in some countries also cordless telephones) is excluded.
This table shows the countries currently under the CTR21 standard.

This information was copied from CETECOM and is supplied without liability. For updates to this table, you may visit http://www.cetecom.de/technologies/ctr_21.html
1 National requirements will apply only if the equipment may use pulse dialling (manufacturers may state in the user guide that the equipment is only intended to support DTMF signalling, which would make any additional testing superfluous).
In The Netherlands additional testing is required for series connection and caller ID facilities.
Federal Communications Commission
Interference Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING! The use of a shielded-type power cord is required in order to meet FCC emission limits and to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
(Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the Federal Register, National Archives and Records Administration, U.S. Government Printing Office.)
FCC Radio Frequency (RF) Exposure Caution Statement
WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
“The manufacture declares that this device is limited to Channels 1 through 11 in the 2.4GHz frequency by specified firmware controlled in the USA.”
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. End users must follow the specific operating instructions for satisfying RF exposure compliance.
Declaration of Conformity (R &TTE directive 1999/5/EC)
The following items were completed and are considered relevant and sufficient:

• Essential requirements as in [Article 3]
• Protection requirements for health and safety as in [Article 3.1a]
• Testing for electric safety according to [EN 60950]
• Protection requirements for electromagnetic compatibility in [Article 3.1b]
• Testing for electromagnetic compatibility in [EN 301 489-1] & [EN 301 489-17]
• Effective use of the radio spectrum as in [Article 3.2]
• Radio test suites according to [EN 300 328-2]

CE Marking
CE marking for devices without wireless LAN/Bluetooth
The shipped version of this device complies with the requirements of the EEC directives 2004/108/EC “Electromagnetic compatibility” and 2006/95/EC “Low voltage directive”.
CE marking for devices with wireless LAN/ Bluetooth
This equipment complies with the requirements of Directive 1999/5/EC of the European Parliament and Commission from 9 March, 1999 governing Radio and Telecommunications Equipment and mutual recognition of conformity.

IC Radiation Exposure Statement for Canada
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with IC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. End users must follow the specific operating instructions for satisfying RF exposure compliance.
Operation is subject to the following two conditions:

• This device may not cause interference and
• This device must accept any interference, including interference that may cause undesired operation of the device.

To prevent radio interference to the licensed service (i.e. co-channel Mobile Satellite systems) this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
This device complies with Industry Canada licence-exempt RSS standard(s).
CAN ICES-3(B)/NMB-3(B)
Wireless Operation Channel for Different Domains

France Restricted Wireless Frequency Bands
Some areas of France have a restricted frequency band. The worst case maximum authorized power indoors are:

• 10mW for the entire 2.4 GHz band (2400 MHz–2483.5 MHz)
• 100mW for frequencies between 2446.5 MHz and 2483.5 MHz

NOTE: Channels 10 through 13 inclusive operate in the band 2446.6 MHz to 2483.5 MHz.
There are few possibilities for outdoor use: on private property or on the private property of public persons, use is subject to a preliminary authorization procedure by the Ministry of Defense, with maximum authorized power of 100mW in the
2446.5–2483.5 MHz band. Use outdoors on public property is not permitted.
In the departments listed below, for the entire 2.4 GHz band:

• Maximum authorized power indoors is 100mW
• Maximum authorized power outdoors is 10mW

Departments in which the use of the 2400–2483.5 MHz band is permitted with an EIRP of less than 100mW indoors and less than 10mW outdoors:

This requirement is likely to change over time, allowing you to use your wireless LAN card in more areas within France. Please check with ART for the latest information (www.arcep.fr)
NOTE: Your WLAN Card transmits less than 100mW, but more than 10mW.

UL Safety Notices
Required for UL 1459 covering telecommunications (telephone) equipment intended to be electrically connected to a telecommunication network that has an operating voltage to ground that does not exceed 200V peak, 300V peak-to- peak, and 105V rms, and installed or used in accordance with the National Electrical Code (NFPA 70).
When using the Notebook PC modem, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• DO NOT use the Notebook PC near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
• DO NOT use the Notebook PC during an electrical storm. There may be a remote risk of electric shock from lightning.
• DO NOT use the Notebook PC in the vicinity of a gas leak.

Required for UL 1642 covering primary (nonrechargeable) and secondary (rechargeable) lithium batteries for use as power sources in products. These batteries contain metallic lithium, or a lithium alloy, or a lithium ion, and may consist of a single electrochemical cell or two or more cells connected in series, parallel, or both, that convert chemical energy into electrical energy by an irreversible or reversible chemical reaction.

• Do not dispose the Notebook PC battery pack in a fire, as they may explode. Check with local codes for possible special disposal instructions to reduce the risk of injury to persons due to fire or explosion.
• Do not use power adapters or batteries from other devices to reduce the risk of injury to persons due to fire or explosion. Use only UL certified power adapters or batteries supplied by the manufacturer or authorized retailers.

Power Safety Requirement
Products with electrical current ratings up to 6A and weighing more than 3Kg must use approved power cords greater than or equal to: H05VV-F, 3G, 0.75mm2 or H05VV-F, 2G, 0.75mm2.
TV Notices
Note to CATV System Installer—Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC),in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable – installation should include bonding the screen of the coaxial cable to the earth at the building entrance.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm.
Macrovision Corporation Product Notice
This product incorporates copyright protection technology that is protected by method claims of certain U.S.A. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Prevention of Hearing Loss
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Nordic Lithium Cautions (for lithium-ion batteries)
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (English)

Optical Drive Safety Information
Laser Safety Information
CD-ROM Drive Safety Warning
CLASS 1 LASER PRODUCT
WARNING! To prevent exposure to the optical drive’s laser, do not attempt to disassemble or repair the optical drive by yourself. For your safety, contact a professional technician for assistance.
Service warning label
WARNING! INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976.
These regulations apply to laser products manufactured from August 1, 1976.
Compliance is mandatory for products marketed in the United States.
WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product installation guide may result in hazardous radiation exposure.
Coating Notice
IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the device except on the areas where the I/O ports are located.
CTR 21 Approval (for Notebook PC with built-in Modem)
The equipment has been approved in accordance with Council Decision 98/4/12/EC for pan-European single terminal connection to the public switched telephone network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.’

ENERGY STAR complied product
ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy helping us all save money and protect the environment through energy efficient products and practices.
All ASUS products with the ENERGY STAR logo comply with the ENERGY STAR standard, and the power management feature is enabled by default. The monitor and computer are automatically set to sleep after 10 and 30 minutes of user inactivity. To wake your computer, click the mouse or press any key on the keyboard. Please visit http://www.energy.gov/powermanagement for detail information on power management and its benefits to the environment. In addition, please visit http://www.energystar.gov for detail information on the ENERGY STAR joint program.
NOTE: Energy Star is NOT supported on FreeDOS and Linux-based operating systems.
Global Environmental Regulation Compliance and Declaration
ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements.
Please refer to http://csr.asus.com/english/Compliance.htm for information disclosure based on regulation requirements ASUS is complied with: Japan JIS-C-0950 Material Declarations
EU REACH SVHC
Korea RoHS
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.
Regional notice for Singapore
Complies with IDA Standards DB103778
This ASUS product complies with IDA Standards.
EC Declaration of Conformity
We, the undersigned,

declare the following apparatus:

X452L, F452L, R412L, D452L, Y482L, E452L, X452E, F452E, R412E, D452E, X452V, F452V, R412V, D452V, X452C, F452C, R412C, D452C, Y482C, X452M, F452M, R412M, D452M, Y482M

conform with the essential requirements of the following directives:
2004/108/EC-EMC Directive

EN 55022:2010+AC:2011
EN 61000-3-2:2006+A2:2009
EN 55013:2001+A1:2003+A2:2006| EN 55024:2010
EN 61000-3-3:2008
EN 55020:2007+A11:2011
---|---

1999/5/EC-R &TTE Directive

EN 300 328 V1.7.1(2006-10)
EN 300 440-1 V1.6.1(2010-08)
EN 300 440-2 V1.4.1(2010-08)
EN 301 511 V9.0.2(2003-03)
EN 301 908-1 V5.2.1(2011-05)
EN 301 908-2 V5.2.1(2011-07)
EN 301 893 V1.6.1(2011-11)
EN 302 544-2 V1.1.1(2009-01)
EN 302 623 V1.1.1(2009-01)
EN 50360:2001
  EN 62479:2010
EN 50385:2002
EN 62311:2008| EN 301 489-1 V1.9.2(2011-09)
EN 301 489-3 V1.4.1(2002-08)
EN 301 489-4 V1.4.1(2009-05)
EN 301 489-7 V1.3.1(2005-11)
EN 301 489-9 V1.4.1(2007-11)
EN 301 489-17 V2.2.1(2012-09)
EN 301 489-24 V1.5.1(2010-09)
EN 302 326-2 V1.2.2(2007-06)
EN 302 326-3 V1.3.1(2007-09)
EN 301 357-2 V1.4.1(2008-11)
EN 302 291-1 V1.1.1(2005-07)
EN 302 291-2 V1.1.1(2005-07)
---|---

2006/95/EC-LVD Directive

2009/125/EC-ErP Directive

Regulation (EC) No. 1275/2008
Regulation (EC) No. 642/2009| Regulation (EC) No. 278/2009
Regulation (EC) No. 617/2013
---|---

2011/65/EU-RoHS Directive
CE marking
Position : CEO
Name : Jerry Shen
(EC conformity marking)
Signature :
Original Declaration Date: 01/08/2013
Corrected Declaration Date: 11/07/2014
Year to begin affixing CE marking: 2014
EC Declaration of Conformity
We, the undersigned,

declare the following apparatus:

0W,D552W,X550J, F550J,K550J,A550J, R510J, Y581J,X552M,F552M ,K552M,A552M,R513M,D552M,Y582M, X552L, F552L, R513L, D552L, Y582L, Y581L, E550L, PRO550L,X550L, A550L, K550L, F550L, R510L, P550L

conform with the essential requirements of the following directives:
2004/108/EC-EMC Directive

EN 55022:2010+AC:2011
EN 61000-3-2:2006+A2:2009
EN 55013:2001+A1:2003+A2:2006| EN 55024:2010
EN 61000-3-3:2008
EN 55020:2007+A11:2011
---|---

1999/5/EC-R &TTE Directive

EN 300 328 V1.7.1(2006-10)
EN 300 440-1 V1.6.1(2010-08)
EN 300 440-2 V1.4.1(2010-08)
EN 301 511 V9.0.2(2003-03)
EN 301 908-1 V5.2.1(2011-05)
EN 301 908-2 V5.2.1(2011-07)
EN 301 893 V1.6.1(2011-11)
EN 302 544-2 V1.1.1(2009-01)
EN 302 623 V1.1.1(2009-01)
EN 50360:2001
  EN 62479:2010
EN 50385:2002
EN 62311:2008| EN 301 489-1 V1.9.2(2011-09)
EN 301 489-3 V1.4.1(2002-08)
EN 301 489-4 V1.4.1(2009-05)
EN 301 489-7 V1.3.1(2005-11)
EN 301 489-9 V1.4.1(2007-11)
EN 301 489-17 V2.2.1(2012-09)
EN 301 489-24 V1.5.1(2010-09)
EN 302 326-2 V1.2.2(2007-06)
EN 302 326-3 V1.3.1(2007-09)
EN 301 357-2 V1.4.1(2008-11)
EN 302 291-1 V1.1.1(2005-07)
EN 302 291-2 V1.1.1(2005-07)
---|---

2006/95/EC-LVD Directive

2009/125/EC-ErP Directive

Regulation (EC) No. 1275/2008
Regulation (EC) No. 642/2009| Regulation (EC) No. 278/2009
Regulation (EC) No. 617/2013
---|---

Ver. 140331

2011/65/EU-RoHS Directive
CE marking
Position : CEO
Name : Jerry Shen
Signature :
Declaration Date: 30/05/2014
Year to begin affixing CE marking: 2014

References

• 華碩永續網站, 華碩永續目標
• ASUS ESG website, ASUS ESG goal
• Chemical Substance Management | Green Material Usage | Circular Economy | ASUS ESG website, ASUS ESG goal
• Manual-Hub.com - Free PDF manuals!
• Homepage | ENERGY STAR
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>