COMP Cams 7100 Billet Timing Sets Instructions
- June 13, 2024
- COMP Cams
Table of Contents
INSTRUCTIONS
COMP Cams Billet Timing Sets
Part #7100, 7102, 7103, 7104, 7108, 7110, 7112, 7122, 7125, 7136, and
7138
7100 Billet Timing Sets
Thank you for choosing COMP Cams® products; we are proud to be your
manufacturer of choice.
Please read this instruction sheet carefully before beginning installation,
and also take a moment to review the included limited warranty information.
COMP Cams® Billet Steel Timing Sets are the most reliable units available.
They give the installer the ability to fine-tune the powerband of the cam by
allowing the cam to be positioned from 0 to 8-degrees advanced or retarded in
2-degree increments. Remember: The camshaft angle is half the crankshaft
angle, therefore the camshaft will correspondingly advance or retard 1, 2, 3
or 4-degrees. This allows the centerline of the camshaft to be “dialed-in”
more accurately than with the use of cam degree bushings.
Installation:
We recommend the chain and sprockets be pre-assembled before final assembly of
the motor to check for any interference between the block and the timing set.
When installing or removing the lower crank gear, which is a “press fit”,
proper puller/installation tools should be used to prevent possible damage to
either the sprocket or the crankshaft snout. Extra care should be given to the
front of the block where cam thrust is set to prevent excessive wear.
Please review the diagram on the back page of these instructions, as your
crank gear may not be stamped showing the timing marks for advancing or
retarding the camshaft. The crankshaft keyway and the correlating cam phase
markings are noted on the diagram. This diagram has been provided to assist in
the more accurate phasing of your camshaft. If you should have any questions
or concerns about your new COMP Cams® 9 Keyway Billet Timing Set or any other
COMP Cams® product, please call our toll free CAM HELP® techline at
1-800-999-0853, 7am-8pm CST, Monday
through Friday and 9am-4pm CST on Saturdays.
Ford Windsor Instructions
To use the thrust bearing in the #7138 kit, you will need to counter sink the
holes in the thrust plate and use counter sink bolts (not included), that will
tighten flush or below the thrust plate surface. Affix the bearing to the
engine side of the sprocket with the black mark facing the engine.
Note: Failure to perform this modification to the thrust plate will
destroy the bearing during installation due to the thrust plate bolt to thrust
bearing contact.
Limited Warranty
Competition Cams, Inc. warrants that all of its products are free from defects
in material and workmanship, and against excessive wear for a period of (1)
one year from the date of purchase. This limited warranty shall cover the
original purchaser. Competition Cams, Inc.’s obligation under this warranty is
limited to the repair or replacement of its product. To make a warranty claim,
the part must be returned within (1) one year of purchase to the address
listed below, freight prepaid. Items covered under warranty will be returned
to you freight collect.
It is the responsibility of the installer to ensure that all of the components
are correct before installation. We assume no liability for any errors made in
tolerances, component selection, or installation.
There is absolutely no warranty on the following:
A) Any parts used in racing applications;
B) Any product that has been physically altered, improperly installed or
maintained;
C) Any product used in improper applications, abused, or not used in
conjunction with the proper parts.
There are no implied warranties of merchantability or fitness for a particular
purpose. There are no warranties, which extend beyond the description of the
face hereof. Competition Cams, Inc. will not be responsible for incidental and
consequential damages, property damage or personal injury damages to the
extent permitted by law. Where required by law, implied warranties or
merchantability and fitness are limited for a term of (1) one year from the
date of original purchase.
This warranty gives you specific legal rights and you may also have other
legal rights, which vary from state to state.
COMP Cams®
3406 Democrat Rd.
Memphis, TN 38118
Phone:901-795-2400 Fax:
901-366-1807
www.compcams.com
Part #161
Revised 11/1/07
Documents / Resources
| COMP
Cams 7100 Billet Timing
Sets
[pdf] Instructions
7100 Billet Timing Sets, 7100, Billet Timing Sets, Timing Sets, Sets
---|---
| COMP
Cams 7100 Billet Timing
Sets
[pdf] Instructions
7100 Billet Timing Sets, 7100, Billet Timing Sets, Timing Sets
| COMP
Cams 7100 Billet Timing
Sets
[pdf] Instructions
7100 Billet Timing Sets, 7100, Billet Timing Sets, Timing Sets, Sets
References
- Performance Camshafts, Lifters, Valve Springs, Rocker Arms - COMP Cams®
- Manual-Hub.com – Free PDF manuals!