velleman DB4 Portable Wireless Door Chime User Manual
- June 13, 2024
- Velleman
Table of Contents
DB4
PORTABLE WIRELESS DOOR CHIME
USER MANUAL
DB4 Portable Wireless Door Chime
Introduction
To all residents of the European Union
Important environmental information about this product This symbol on the
device or the package indicates that disposal of the device after its
lifecycle could harm the environment. Do not dispose of the unit (or
batteries) as unsorted municipal waste; it should be taken to a specialized
company for recycling. This device should be returned to your distributor or
to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before
bringing this device into service. If the device was damaged in transit, don’t
install or use it and contact your dealer.
Safety Instructions
Keep the device away from children and unauthorised users.
Keep this device away from rain, moisture, splashing and dripping liquids
- Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
- Note that damage caused by user modifications to the device is not covered by the warranty.
General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
- Protect this device from shocks and abuse. Avoid brute force when operating the device.
- Protect the device against extreme heat and dust.
- Familiarise yourself with the functions of the device before using it.
- All modifications of the device are forbidden for safety reasons.
- Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
Features
- encoded signal prevents false alarm
- easy installation without cables
- 3 different chimes: ding, ding-dong, Westminster
- 2 doorbell push buttons: a different doorbell melody can be set for each push button
- 16 codes
- comes with:
- 1x doorbell
- 2x doorbell push button
- 2x 12Vdc battery, type A23 (for push buttons)
Overview
Refer to the illustrations on page 2 of this manual.
doorbell
- 4.5VDC input jack
- speaker”
- status LED
- DIP switch + cover
- battery compartment
doorbell push button (2x)
A push button
B activate chime button (= A)
C select melody jumpers
D DIP switch
E battery compartment
Operation
-
Insert batteries (not incl.) into the doorbell (see §8) or connect a 4.5VDC adaptor (not incl.) to the 4.5VDC input jack [1].
Polarity for the adaptor: -
Open the DIP switch cover [4] of the doorbell. Releasing the screw and remove the cover.
-
Open the doorbell push buttons by pushing gently with a small screwdriver in the gap at the bottom of the casing (see arrow) and removing the back cover.
-
Insert the batteries into the doorbell push buttons (see §8).
-
Verify that the settings of the DIP switches of the doorbell [4] and doorbell push buttons [D] are the same. These DIP-switches set the encoding of the transmitted signal. When interference ith similar devices in the neighbourhood is noticed, change the DIP-switch setting, but make sure that the same setting is selected on doorbell and doorbell push-buttons.
-
Both doorbell push buttons can have their own melody setting. Set the melody jumper [C] to the desired melody:
1 für Elise 2 Westminster 3 ding-dong -
Close the DIP switch cover [4] of the doorbell. Secure the screw.
-
Mount or place the doorbell push buttons in the desired locations and close the doorbell push buttons. Protect them from harsh weather conditions to prolong their life time. Make sure push buttons are not surrounded by metal or near a strong magnetic field.
-
Mount or place the doorbell itself in the desired location (indoors only). Make sure the doorbell is not surrounded by metal or near a strong magnetic field.
-
A push on the doorbell button will produce the chosen melody for that button through the speaker [2] of the doorbell, while the status LED [3] is lit.
Troubleshooting
- When sound becomes weak, replace the batteries of the doorbell (see §8).
- When pushing a push button does not produce a chime:
- verify whether the DIP switch settings on doorbell and doorbell push buttons are identical. Set the same setting on doorbell and doorbell push buttons.
- verify whether the push button is located within the specified range (max. 60m). If not, bring it closer to the doorbell.
- verify whether doorbell and doorbell push buttons are not surrounded by metal or near a strong magnetic field. In these cases, move the push button or doorbell to a suitable location.
- replace the push button battery (see §8)
Batteries
doorbell
- Open the battery compartment [5].
- Insert 3 new 1.5V batteries type AA (LR6C) with polarity as indicated inside the battery casing.
- Close the battery compartment.
doorbell push button
- Open the doorbell push buttons by pushing gently with a small screwdriver on the bottom of the casing (see arrow) and removing the back cover.
- Insert a new 12V battery type GP23A with polarity as indicated on the illustration (see page 2 of this manual).
general
- Do not attempt to recharge non-rechargeable batteries and do not throw batteries in fire as they might explode.
WARNING: handle batteries with care, observe warnings on battery casing. Dispose of batteries in accordance with local regulations. Keep batteries away from children.
Technical Specification
transmission frequency | 433.92MHz |
---|---|
range | max. 60m |
power supply | 3.5mm |
each doorbellpush button | 1 x 12V battery GP23GAC (incl.) |
doorbell | 3 x AA battery 1.5V (LR6C, not incl.) |
or
power adaptor 4.5VDC/5W (PSS0530, not incl.)
Use this device with original accessories only. Velleman nv cannot be held
responsible in the event of damage or injury resulted from (incorrect) use of
this device.
For more info concerning this product, please visit our website
www.velleman.eu.
The information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
This manual is copyrighted. The copyright to this manual is owned by Velleman
Components nv. All worldwide rights reserved. No part of this manual may be
copied, reproduced, translated or reduced to any electronic medium or
otherwise without the prior written consent of the copyright holder.
Velleman® Service and Quality Warranty
Velleman® has over 35 years of experience in the electronics world and
distributes its products in more than 85 countries. All our products fulfil
strict quality requirements and legal stipulations in the EU. In order to
ensure the quality, our products regularly go
through an extra quality check, both by an internal quality department and by
specialized external organisations. If, all precautionary measures
notwithstanding, problems should occur, please make appeal to our warranty
(see guarantee conditions).
General Warranty Conditions Concerning Consumer Products (for EU):
-
All consumer products are subject to a 24-month warranty on production flaws and defective material as from the original date of purchase.
-
Velleman® can decide to replace an article with an equivalent article, or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible, or if the expenses are out of proportion.
You will be delivered a replacing article or a refund at the value of 100% of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery, or a replacing article at 50% of the purchase price or a refund at the value of 50% of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery. -
Not covered by warranty:
– all direct or indirect damage caused after delivery to the article (e.g. by oxidation, shocks, falls, dust, dirt, humidity…), and by the article, as well as its contents (e.g. data loss), compensation for loss of profits;
– frequently replaced consumable goods, parts or accessories such as batteries, lamps, rubber parts, drive belts… (unlimited list);
– flaws resulting from fire, water damage, lightning, accident, natural disaster, etc.
– flaws caused deliberately, negligently or resulting from improper handling, negligent maintenance, abusive use or use contrary to the manufacturer’s instructions;
– damage caused by a commercial, professional or collective use of the article (the warranty validity will be reduced to six (6) months when the article is used professionally);
– damage resulting from an inappropriate packing and shipping of the article;
– all damage caused by modification, repair or alteration performed by a third party without written permission by Velleman®. -
Articles to be repaired must be delivered to your Velleman® dealer, solidly packed (preferably in the original packaging), and be completed with the original receipt of purchase and a clear flaw description.
-
Hint: In order to save on cost and time, please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair. Note that returning a non-defective article can also involve handling costs.
-
Repairs occurring after warranty expiration are subject to shipping costs.
-
The above conditions are without prejudice to all commercial warranties.
The above enumeration is subject to modification according to the article (see article’s manual).
R & TTE Declaration of Conformity
We
Velleman Components NV
Legen Heirweg, 33
9890 Gavere (België)
Declare on our own responsibility that the finished product(s) :
Brand :
VELLEMAN
Trade name commercial :
WIRELESS DOOR BELL
Type or model :
DB4
constituting the subject of this declaration, conforms with the essential
requirements and other relevant stipulations of the R&TTE Directive
(1999/5/EC).
The product conforms to the following norm(s) and/or one or several other
normative documents:
EMC :
EN 301 489-1 v1.7.1 (2006-07)
EN 301 489-3 v1.4.1 (2002-08)
LVD:
EN 60950-1 : 2001 + A11 :2004
R &TTE:
EN 300 220-1 v2.1.1 (2006-04)
EN 300 220-2 v2.1.1 (2006-04)
Technical data are available and can be obtained from :
Velleman Components NV
Legen Heirweg, 33
9890 Gavere (België)
Place and date of issue
Gavere, 5/1/2009
Authorised signatory for the company
Mr. Luc De Meyer – Purchasing Manager
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>