Talon CVD10 Pipe Cover Backplates Instruction Manual
- June 13, 2024
- Talon
Table of Contents
CVD10 Pipe Cover Backplates
Instruction Manual
Talon Pipe Cover Range
Pipe Cover Range
Talon Pipe Cover has been designed to offer a compact, neat and easy solution
where unsightly pipework needs to be covered. Available in 15, 22 & 28mm
single and 10, 15 & 22mm double styles, it can be fitted directly onto the
Talon Hinged Clips.
Colours & sizes
|
---|---
CVD10
10mm Double Pipe Cover
A: 25mm B: 46mm| CVD15
15mm Double Pipe Cover
A: 33mm B: 58mm
|
CVD22
22mm Double Pipe Cover
A: 40.7mm B: 78mm| CVS15
15mm Single Pipe Cover
A: 33mm B: 33mm
|
CVS22
22mm Single Pipe Cover
A: 40.7mm B: 43mm| CVS28
28mm Single Pipe Cover
A: 48mm B: 53mm
Pipe Cover Backplates
Replaces fixing bracket for installations not involving Talon Hinged Clips.
Spacing between back plates: No more than 1 meter apart.
How to -Talon Pipe Cover
How to install Talon Pipe Cover
Talon Pipe Cover is specially designed to grip and hold Talon Hinged Clips.
Cover is available for single or double pipe installations. Pipe Cover is
fully adaptable for use with non Hinged Clip specifications (see page 3 TBC)
Required for Install…
Typical parts required to install a length of Pipe Cover includes;
- Talon Hinged Clips
- Talon Red or Brown Wall Plugs
- Size 10 countersunk screws
- Installation pipework.
Step 1
Drill holes then install Talon Hinged Clips & Talon Wall Plugs with screws on
fixing surface. Space clips no more than 500mm apart along the Pipe Cover.
Step 2
Install pipe then place Pipe Cover over Hinged Clips. Note the cover fixing
points are specially designed to grip the side lugs of Talon Hinged Clips.
Step 3
Push the Pipe Cover and Hinged Clip fixing points together to close the
installation.
Repeat for additional coverings adding Talon extension accessories where
needed.
How to – Pipe Cover Backplates
Pipe Cover Backplates
Required for Install…
A typical cover installation involving backing plates will need additional
fixings. Backing plates required;
- Talon Open Clips or other clips fit for a pipework install.
- Talon Red or Brown Wall Plugs
- Size 10 countersunk screws
Step 1
Drill required holes and fix the backing plates and pipe clips. Backing plates
should be spaced no more than 500mm apart along the pipe cover installation.
Step 2
Install the pipework. Note the backing plate sits under the pipework. A
minimum gap of 7mm is required between the fixing surface and the installed
pipe.
Step 3
Place the pipe cover over the installation and push fixing points together to
finish the installation. Repeat process for additional Pipe Cover.
For more information on Pipe Cover Accessories, see data sheets for more details.
Talon Pipe Cover Accessories
Pipe Cover Accessories
Talon offer a wide range of Pipe Cover Accessories to fit to Talon Pipe Cover
and used in conjunction with Talon Skirting Cover.
Colours & sizes
Single Pipe Cover Accessories
Double Pipe Cover Accessories
Single Pipe Cover Accessories
10mm Double Pipe Cover Accessories
15mm Double Pipe Cover Accessories
22mm Double Pipe Cover Accessories
Additional Accessories
| |
---|---|---
AVP20
20mm Vent Plug
A: 2mm B: 23.5mm
Drill hole size = 20mm| AVP70
70mm Vent Plug
A: 1.75mm B: 80mm
Drill hole size = 70mm| AK105T15 (15mm)
Skirting Cover T Connector
A: 150mm B: 62mm
C: 85mm
How to – Pipe Cover Accessories
Talon Pipe Cover Accessories combine in a variety of ways to cover
installation work.
Accessories are easy fit using uPVC Solvent Weld Glue. The Skirting Crossover
T Connector allows Talon Skirting Cover to be connected to Talon Pipe Cover.
Information Sheet No. 3A – © Talon Manufacturing
Talon, Units 2 to 5 Chieftain Close, Gillingham Business Park, Kent, ME8 0PP
Tel: 01634 268811 ◦ Fax: 01634 268812
◦ Email: [email protected]
◦ Web: www.talon.co.uk
Version: 2
Page 8 of 8
15.03.19