Peavey SSE-12 Two-Way Speaker System Specifications and Datasheet

Peavey SSE-12 Two-Way Speaker System

Description

The SSE is a new enclosure series featuring high power ratings with custom components, a sleek look, and a unique, snap-in metal grille. The SSE 12 is a two-way system featuring the highly acclaimed Peavey 14T titanium compression driver with the diverse Sound Guard IV tweeter protection network and Peavey 12″ woofer with a 2.5″ (64 mm) voice coil for smooth response. The SSE 12 is rated at 500 Watts program and 1,000 Watts peak. This lightweight speaker system is ideal for smaller venues where space is at a premium. Connections are made using a four-pin twist lock connector or a paralleled two-position terminal block for additional cabinets. The SSE 12 incorporates flying points on the top of the unit and mounting points on the bottom for utilizing the Peavey VersaMount 70 mounting bracket. The SSE Series is available in black or white finishes.

Features

• Two-way sound reinforcement enclosure
• Designed for permanent install
• Available in black or white finishes
• Peavey 12″ woofer with 2.5″ (64 mm) voice coil
• Peavey 14T titanium diaphragm compression driver
• Sound Guard IV tweeter protection network
• Seven flying points (six M10 for suspension and one M6 for angle adjustment)
• Mounting point for VersaMount 70 bracket
• 13 mm birch plywood construction
• 500 Watts program / 1000 Watts peak power handling
• 79 Hz to 17 kHz
• 98 dB at 1W/1m
• 8 Ohms

Frequency Response

• 1-meter on-axis, swept-sine in the anechoic environment: 79 Hz to 17 kHz (±3 dB)
• Usable low-frequency limit (-10 dB point): 60 Hz

Power Handling

• Full range: 500 W program / 1,000 W peak

Sound Pressure Level

• 1 Watt, 1 meter in an anechoic environment:

  • Full range: 98 dB SPL (2.83 V input)

• Maximum sound pressure level (1 meter):

  • Full range: 122 dB SPL continuous / 128 dB SPL peak

• Radiation Angle Measured at -6 dB Point of Polar Response

  • 500 Hz to 1.6 kHz:
  • Horizontal: 110° ± 15°
  • Vertical: 120° ± 30°
  • 1.6 kHz to 5 kHz:
  • Horizontal: 75° ± 15°
  • Vertical: 70° ± 25°
  • 5 kHz to 16 kHz:
  • Horizontal: 85° ± 15°
  • Vertical: 40° ± 10°

• Directivity Factor, Q (Mean):

  • 10.27 ± 6.07

• Directivity Index, Di (Mean):

  • 9.38 dB ± 2.57 dB

• Transducer Complement:

  • Low-Frequency Section:
  • Peavey woofer with 2.5″ (64 mm) voice coil
  • High Frequency Section:
  • Peavey 14T™ titanium diaphragm compression driver on a 90° x 40° constant directivity horn

• Box Tuning Frequency:

  • Low-frequency section: 74 Hz

• Harmonic Distortion:

  • 1% rated power:
  • Second harmonic:
  • 100 Hz: 0.32%
  • 1 kHz: 0.10%
  • Third harmonic:
  • 100 Hz: 0.40%
  • 1 kHz: 0.22%
  • 10% rated power:
  • Second harmonic:
  • 100 Hz: 0.56%
  • 1 kHz: 0.79%
  • Third harmonic:
  • 100 Hz: 0.79%
  • 1 kHz: 0.25%

• Electro-Acoustic Crossover Frequency (Internal Passive):

  • 2.8 kHz

• Impedance (Z):

  • Full range:
  • Nominal: 8 Ω
  • Minimum: 5.1 Ω

• Input Connection:

  • 1 four-pin twist lock connector in parallel with one 1-position terminal strip

• Enclosure Materials and Finish:

  • Trapezoidal, dado-joined 13 mm birch enclosure finished with a textured acrylic polyurethane with a full-length metal grille covered and acoustical-grade grille cloth. Available in black or white finishes.

• Mounting Provisions:

  • (6) M10 threaded mounting suspension points (three on each top and one on each side and back).
  • (1) M6 x 1.0mm threaded mounting point on the back bottom for angle adjustments.
  • (4) M6 x 1.0mm threaded mounting points on the bottom to accommodate the use of VersaMount™ 70 adjustable mounting bracket.
  • DO NOT suspend this unit upside down using the VersaMount system.

• Dimensions (H x W x D):

  • Front:
  • 24.5″ x 17.43″ x 13.20″ (622 mm x 443 mm x 335 mm)
  • Rear:
  • 24.5″ x 13.14″ x 13.20″ (622 mm x 334 mm x 335 mm)

• Net Weight:

  • 40 lbs. (18.1 kg)

• Frequency Response:

  • This measurement is useful in determining how accurately a given unit reproduces an input signal. The frequency response of the SSE 12 is measured at a distance of 1 meter using a 1 Watt (into the nominal impedance) swept-sine input signal. As shown in Figure 1, the selected drivers in the SSE 12 combine to give a smooth frequency response from 79 Hz to 17 kHz.

• Directivity:

  • Beamwidth is derived from the -6 dB points from the polar plots (see Figure 3) which are measured in a whole space anechoic environment. Q and the Directivity Index are plotted for the on-axis measurement position. These specifications provide a reference to the coverage characteristics of the unit and provide insight into proper placement and installation in the chosen environment. The blending of the components of the SSE 12 exhibits a desirable beamwidth and directivity (figures 3 & 4) suitable for sound reinforcement applications.

• Power Handling:

  • There are many different approaches to power-handling ratings. Peavey rates this loudspeaker system’s power handling using a full-range form of the AES Standard 2-1984. Using an audio band of 20 Hz to 20 kHz pink noise with peaks of four times the RMS level, this strenuous test signal assures the user that every portion of this system can withstand today’s high-technology music. This rating is contingent upon having a minimum of 3 dB of amplifier headroom available.

• Mounting:

  • Caution: Before attempting to suspend or mount this speaker, consult a certified structural engineer. The speaker may fall due to improper installation, resulting in serious injury and property damage. DO NOT suspend or mount any other product or device from this enclosure. The maximum enclosure angle is 45°. Use only Grade 8.8 Metric hardware or better. All rigging is the responsibility of others.

• Architectural and Engineering Specifications:

  • The loudspeaker system shall have an operating bandwidth of 79 Hz to 17 kHz. The nominal output level shall be 98 dB when measured at a distance of 1 meter with an input of 1 watts. The nominal impedance shall be 8 Ohms. The maximum program power handling shall be 500 Watts with a peak power input of at least

NOTE: Features and specifications are subject to change without notice.

WARRANTY INFORMATION AVAILABLE ONLINE

AmplitudeResponse

AmplitudeResponse(1W1mOn-Axis)

Impedance

Beamwidth

Q &DirectivityIndex

HarmonicDistortion:10%RatedPower

HarmonicDistortion:1%RatedPower

Vertical Polar Patterns 6 dB per Division

Vertical Polar Patterns 6 dB per Division

Vertical Polar Patterns 6 dB per Division

Horizontal Polar Patterns 6 dB per Division

Horizontal Polar Patterns 6 dB per Division

Horizontal Polar Patterns 6 dB per Division

Input Plate

Flying/Rigging Information

Caution: Before attempting to suspend this speaker, consult a certified structural engineer. Speakers can fall from improper suspension, resulting in serious injury and property damage. Do not suspend or mount any other product or device from this enclosure! Maximum enclosure angle 30°. Use only the correct mating hardware. All associated rigging is the responsibility of others. DO NOT OVER TORQUE HARDWARE. ALWAYS USE SAFETY CHAIN. INSPECT RIGGING ANNUALLY.

Hardware for Flying/Rigging

Bracket bolts should be metric thread grade 8.8 or better. Eyebolts and bracket bolts must conform to certain minimum strength criteria for safety reasons. Unspecified eyebolts found at local hardware stores are not strong enough to maintain safety for overhead flying or rigging. Use only forged steel shoulder machinery eyebolts designed for rigging use. Eyebolts should comply with one of the following standards: DIN 580, ASTM A489, or the German BGV-C1 specification. This Peavey loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in this User’s Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal suspension ordinances.

www.peavey.com

Warranty registration and information for U.S. customers are available online at www.peavey.com/warranty or use the QR tag below

Features and specifications are subject to change without notice.

Peavey Electronics Corporation 5022 Hartley Peavey Drive Meridian, MS 39305 601-483-5365 FAX 601-486-1278

Logo referenced in Directive 2002/96/EC Annex IV (OJ(L)37/38,13.02.03 and defined in EN 50419: 2005

The bar is the symbol for marking new waste and is applied only to equipment manufactured after 13 August 2005

FAQs

What type of speaker system is the Peavey SSE-12?

The Peavey SSE-12 is a two-way sound reinforcement enclosure.

What are the key components of the SSE 12's speaker drivers?

The SSE 12 features a Peavey Scorpion Pro 1200+ 12

Does the SSE 12 have any tweeter protection features?

Yes, it is equipped with the Sound Guard IV tweeter protection network.

What is the power rating of the SSE 12?

The SSE 12 is rated at 500 Watts program and 1,000 Watts peak.

How can I connect additional cabinets to the SSE 12?

You can make connections using a four-pin Neutrik Speakon or a paralleled two- position terminal block for additional cabinets.

Does the SSE 12 have mounting options?

Yes, it incorporates flying points on the top of the unit and mounting points on the bottom for utilizing the Peavey VersaMount70 mounting bracket.

What finishes are available for the SSE Series?

The SSE Series is available in black and off-white finishes.

What is the recommended application or use for the SSE 12 speaker system?

The SSE 12 is suitable for sound reinforcement and is often used in smaller venues where space is limited.

Can the SSE 12 be used in both indoor and outdoor settings?

The SSE 12 is primarily designed for indoor use. While it may work outdoors, it's recommended to protect it from exposure to the elements.

What type of power source does the SSE 12 require?

The SSE 12 operates on corded electric power.

What are the dimensions and weight of the SSE 12 speaker?

The SSE 12 has dimensions of 39.24 x 19.75 x 27.75 inches and weighs approximately 21 pounds.

Can the SSE 12 be used as part of a larger sound system or setup?

Yes, the SSE 12 can be integrated into larger sound systems when needed, and it supports connections with additional cabinets.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>