AprilAire Z10ODT Wireless Outdoor Temperature and Humidity Sensor Instruction Manual

Sensor
INSTALLATION AND
OPERATOR’S MANUAL
Model Z10ODT
Wireless Outdoor Temperature
and Humidity Sensor
READ AND SAVE THESE INSTRUCTIONS

DIMENSIONS

SPECIFICATIONS

outside of this range
Range: -40°F to 125°F
Humidity measurement range/accuracy| Accuracy: ±5% RH between 20% and 80% RH
Range: 0.5% to 99.5% RH
Battery life| Approximately 2 years
Battery type| Lithium CR2477 type

FEATURES

WHEN USED WITH A THERMOSTAT, THE WIRELESS OUTDOOR SENSOR CAN BE USED TO:

• More efficiently control an air source heat pump with balance points.
• Enable automatic humidification.
• Enable ventilation lockouts.
• Display of outdoor temperature.

BATTERY REPLACEMENT

1. Remove screw at the bottom of the backing plate.

2. Remove sensor from backing plate.

3. Remove 4 screws from back.

4. Carefully separate front and back of sensor case.
   Be careful to not damage or lose the rubber gaskets (4 round screws gaskets, 1 large gasket).

5. Remove green circuit board.

6. Slide battery out of clip.

7. Replace battery with lithium CR2477 type.

8. Replace cover making sure all 5 gaskets and the button cover are in place.

9. Replace sensor on backing plate.

10. Replace bottom screw to secure sensor to mounting bracket.
    

MOUNTING THE WIRELESS OUTDOOR SENSOR

NOTE: Pair sensor with Wi-Fi thermostat before mounting.
The sensor should be mounted:

• Within 35 feet of the thermostat.
• Away from large metal obstructions that could reduce wireless communication range.
• Away from direct rainfall (the unit is water resistant not water proof).
• On a vertical exterior wall, at least 6 inches below any overhang.
• Protected from direct sunlight (north side recommended).
• At least 3 feet away from exhaust vents and condensing lines.
• Above the snow line.
• Accessible for easy battery replacement.

PAIRING THE SENSOR TO THE S86WMUPR THERMOSTAT

1. On the thermostat, navigate to wireless sensor settings: Menu > Settings > Installer Settings (press and hold UP and DOWN 5 seconds) > Wireless Sensors > Add.

2. On the sensor, press and hold the pairing button 5 seconds (the red indicator on the front of the sensor will start flashing).

3. On the thermostat, select Continue and wait for the pairing process to complete.

LOW BATTERY DISPLAY

When the battery gets below 30% life left the sensor will flash the LED once every 10 seconds. The connected/paired device will display sensor low battery screen (see your thermostat or connected device manual).

SENSOR LED AND BUTTON FUNCTIONALITY

LED STATUS

Flashes once per second| Connectivity status (pairing mode).
NOTE: The sensor exits pairing mode after 30 seconds.
Flashes once per 10 seconds| Battery low power status.
BUTTON FUNCTION

Press and hold 5 seconds| Enter pairing mode.

TROUBLESHOOTING

If the wireless sensor is experiencing connection issues with the thermostat, verify the following:

1. Connect the thermostat to a Wi-Fi network to verify the latest firmware is installed. The latest firmware will automatically install once connected to Wi-Fi.
2. On the sensor, press and release the pairing button once. This will send updated information to the thermostat.
3. On the thermostat, navigate to wireless settings: Menu > Settings > Installer Settings (press and hold UP and DOWN 5 seconds) > Wireless Sensors > View.
4. Note the RSSI value located within the View Sensor screen. The RSSI value should be greater than -70 dBm (see illustration below).
   a. If the RSSI value is less than -70 dBm, relocate the sensor and repeat steps 2-4.
   b. If the RSSI is greater than -70 dBm and connection issues persist, contact AprilAire customer support at 800.334.6011.

IC WARNING

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device

FIVE YEAR LIMITED WARRANTY

Your AprilAire® Wireless Indoor Temperature and Humidity Sensor is expressly warranted for five (5) years from date of installation to be free from defects in materials or workmanship.
AprilAire’s exclusive obligation under this warranty shall be to supply, without charge, a replacement for any sensor which is found to be defective within such five (5) year period and which is returned, together with  the date of installation, no later than thirty (30) days after said five (5) year period by you to either your original supplier or to AprilAire, Madison, Wisconsin 53701.
THIS WARRANTY SHALL NOT OBLIGATE APRILAIRE FOR ANY LABOR COSTS AND SHALL NOT APPLY TO DEFECTS IN WORKMANSHIP OR MATERIALS FURNISHED BY YOUR INSTALLER AS CONTRASTED TO DEFECTS IN THE SENSOR ITSELF.
IMPLIED WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE AFORESAID FIVE YEAR PERIOD. APRILAIRE’S LIABILITY FOR  INCIDENTAL OR CONSEQUENTIAL DAMAGES, OTHER THAN DAMAGES FOR PERSONAL INJURIES, RESULTING FROM ANY BREACH OF THE AFORESAID IMPLIED WARRANTIES OR THE ABOVE  LIMITED WARRANTY IS EXPRESSLY EXCLUDED. THIS LIMITED WARRANTY IS VOID IF DEFECT(S) RESULT FROM FAILURE TO HAVE THIS SENSOR INSTALLED BY A QUALIFIED HEATING AND AIR  CONDITIONING CONTRACTOR. IF THE LIMITED WARRANTY IS VOID DUE TO FAILURE TO USE A QUALIFIED CONTRACTOR, ALL DISCLAIMERS OF IMPLIED WARRANTIES SHALL BE EFFECTIVE  UPON INSTALLATION.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above exclusions or limitations may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
This equipment if installed in strict accordance with the manufacturer’s instructions, complies with the limits for a Class B computing device pursuant to Subpart J of Part 15 of FCC Rules.

WARRANTY REGISTRATION
Visit us on-line at aprilaire.com to register your AprilAire product. If you do not have on-line access, please mail a postcard with your name, address, phone number, product purchased and date of purchase to:  AprilAire, P.O.
BOX 1467, Madison, WI 53701
Your warranty registration information will not be sold or shared outside of this company.

FCC AND ISED COMPLIANCE STATEMENTS

Contains FCC ID: 2AUXB-DSBC060
Contains IC: 25658-DSB060
This device complies with Part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada’s License-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
   Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Interference Statement – Part 15.105 (b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to  radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

To comply with FCC and Innovation, Science and Economic Development Canada’s RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this transmitter must be installed to  provide a separation distance of at least 20 cm from all persons and must not be operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures.

B2209578B • 61002020 • 02.23
© 2023 AprilAire | aprilairepartners.com | 800.334.6011
AprilAire reserves the right to change specifications without notice.

References

• AprilAire Home
• AprilAire Partners

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>