maytronics LIBERTY Robotic Cordless Pool Cleaner Instruction Manual
- June 13, 2024
- maytronics
Table of Contents
Safety Instructions
**Maytronics Dolphin Robotic Pool Cleaner
Exceptional Exprience**
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
Please adhere strictly to the following WARNINGS:
Remove the robotic pool cleaner from the pool before allowing people to enter
the pool.
When examining the robotic pool cleaner, make sure the robotic pool cleaner is
switched OFF.
Charge the battery only in the temperature range between 43°F to 95°F / 6°C to
35°C
Keep the robotic pool cleaner out of the reach of children or persons with
reduced physical, sensory, or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction.
Cleaning and maintenance shall not be made by children.
Use only the original battery charger.
-
The battery charger must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.
For USA/Canada installations: -
The battery charger must be connected only to a supply circuit that is protected by a ground fault circuit interrupter (GFCI). This GFCI should be tested on a routine basis.
-
To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective.
-
If the GFCI interrupts power to the battery charger without the test button being pushed, a ground current may be flowing, indicating the possibility of an electric shock. Do not use the battery charger. Disconnect the battery charger and contact the manufacturer for assistance.
The power cord is not user-replaceable. If the power cord is damaged, stop using the battery charger and contact the service center for repair.
Do not use extension cord to connect the battery charger to electric supply; provide a properly located outlet.
DO NOT USE the robotic pool cleaner and/or its battery / power pack in case of mechanical damage to the robotic pool cleaner and/or its battery.
To avoid the risk of fire and burns, DO NOT open, crush, heat, or burn the battery case.
Please ensure that the following PRECAUTIONS are implemented:
For continuous protection against possible electric shock, place the battery
charger at least 4 in / 11 cm above ground.
Position the battery charger at least 12 ft / 3.5 m from pool edge during
operation.
Keep hands and fingers away from impeller motor area and driving belt
mechanism to avoid injury.
When lifting the robotic pool cleaner, take care to prevent back injury.
Do not use the robotic pool cleaner if you have added liquid flocculant or any
other clarifier to the pool water.
These substances obstruct and damage the robot filters.
**** The Lithium-Ion battery in this product is non-replaceable. It should be
recycled at certified battery electronics recyclers that accept batteries.
Batteries should NOT be discarded in the trash or put in municipal recycling
bins. Do not disassemble the battery.
Specifications
Robot
- Motor protection: IP68
- Minimum depth: 1.33 ft / 0.4 m
- Maximum depth: 8.2 ft / 2.5 m
Battery Charger
- Protection: IP54
- Output: <30 VDC
Water Conditions
Use only the robotic pool cleaner in the following water conditions:
-
Chlorine: 4 ppm max.
-
pH: 7.0 – 7.8
-
Temperature: 43°F – 95°F / 6°C – 35°C
Note: below 59°F / 15°C, climbing performance may be affected. -
NaCl: 5000 ppm max.
SAVE THESE INSTRUCTIONS
– Liberty Safety Instructions
For full information, please contact us atwww.maytronics.com/contact-us-
en and ask for the EU Declaration of
Conformity.
8180137 Rev.01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>