Brightown CPFLM508 Christmas Decorative Lights User Manual
- June 13, 2024
- Brightown
Table of Contents
Brightown CPFLM508 Christmas Decorative Lights
Unpacking Instruction
Read Manual before Operation
Dear user, Thanks for choosing our LED device, I believe this brand-new
product will bring you unlimited marvels and happiness. Before operating this
device, please read this manual thoroughly, and retain it for future
reference.
WARNING
Please note the warnings in bold which will ensure the safe and smooth operation. These warnings are important to a certain extent.
- Attention! Indicates a skill or other useful information for special situations.
- Important! Indicates important information to protect personnel from laser incidents or injury .
- Caution! Prevent damage or injury from incorrect operation
Warning!
Shields, lenses or ultraviolet screens shall be changed if they have become
visibly damaged to such an extent that their effectiveness is impaired, for
example by cracks or deep scratches. The fixture shall be changed if it has
become damaged or thermally deformed .
Unpacking Instruction
As you receive a fixture, carefully unpack the carton, check the contents to ensure that all parts are in good condition. Informing the shipper immediately and retaining packing material for inspection if any parts damaged from shipping or device damaged. Keeping packing materials as evidence for the shipper’s confirmation.
FCC
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
Before You Begin
Carefully unpack package contents to make sure all parts are presented. Some
assembly is required.
Note : For your convenience, one slide is inside of the projector
.
WARNING I
- Do not ingest the battery, Chemical Burn Hazard (The remote control supplied with)
- This product contains a coin/button cell battery.If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
IMPORTANT SAFEGUARDS
To reduce the risk of fire, electric shock, or injury when using any electric
appliance precautions should be made. These precautions include but are not
limited to:
Safety Instruction
CAUTION! – Use only as directed.
- This product has a polarized plug to reduce the risk of electric shock. It will therefore only fit into a polarized outlet one way. If the plug does not fit, reverse the plug. If it still does not fit, contact a qualified electrician. Do not use with an extension cord unless the plug can be fully inserted. Do not alter the plug.
- DO NOT attempt to open the protective housing or operate the device if the aperture windows are damaged. If the unit requires service that involves removing the protective housing, contact the manufacturer. Opening the protective housing voids the warranty.
- When the power cord interface of the lamp body is inserted into the power supply, it has a directional orientation. If the direction is not correct.it will damage the power supply or the power cord, the right insert as shown below:
Power cord red circle protruding position
Power supply Red circle in the recessed position
Product instruction
Assemble
- To attach ground stake, remove the screw from the stake.
- Use the screw to attach the stake to the pivot mount (see fig. 1 ).
- Plug the2-prong adapter into the outlet on the power supply transformer.
- Screw on the weather-resistant cap tightly to help protect the connection from weather.
Installing Slides
Unscrew and remove the two screws holding the slide frame in the projection
light casing. Remove the slide frame (see fig. 2).
One slide is already put in the slide frame.In order to install a different
slide, remove the preloaded slide by pushing it out of the frame while being
careful to avoid touching the slide images.
The slide should easily pop out.
Placing the Projector Light
- The projector light can be staked into the ground. With the stake removed, it can also be mounted to a structure using a sturdy hanging clamp and safe cable.
- Place light approximately 1 O to 15 feet from the projection surface. After the light is turn down you may need to adjust the distance to get the best results.
Note : If you insert a different slide, you may need to adjust the distance for clarity .
Product Specification
Remote control function description
- Note: The fixture integrates with 6 hours automatic shutdown function which means working 6 hours, and shutting down for 18 hours.
- Buttons in the red area control the card light function, buttons in the light blue area control the water light function
