i-PRO WV-QCL100-W Ceiling Mount Bracket Instruction Manual

Recommended pipe:
ø48.6 mm {1-29/32 inches}

t = 3.5 mm {1/8 inches}

Material: Stainless Steel

Maximum permissible length:

1.5 m {59-1/16 inches}

Step 1 (Continued)

【 4】 Check the position for fixing this product (in 2 places) and pipe, and the position for fixing the camera to this product, before mounting.

When attaching using the attachment plate (holes of Ⓐ): Each series of S61xx, S22xx, S21xx, S41xx . Step 2
When attaching the camera directly to this product (holes of Ⓑ) S31xx series . Step 8
When attaching the camera directly to this product (holes of Ⓒ) using holes of fixing pitch 83.5 mm {3-9/32 inches}

NOTE

• The position for fixing this product will change depending on the pipe (locally procured) tapping variation. Be sure to attach this product to the pipe, and confirm the transition in the rotation direction of this product on the ceiling and camera before deciding the attachment position.
• For S31xx Series, the shooting direction of the camera is restricted. (Refer to Step 8) Be sure to attach the camera to this product (used on camera), and the pipe to this product (used on ceiling) and check the post-attached camera direction before using it.

Step 2 Fix this product (used on ceiling) to the ceiling.

• Decide the location where this product is to be attached on the ceiling, then makthe holes for fixing and wiring as shoin the illustration on the right.

• Thread the cables and the safety wire through this product (used on ceiling), then fix to the ceiling. Fixing screws (4 pcs.) (M4: locally procured) Minimum pullout strength: 196 N {44 lbf} (per 1 pc.)

• The following explanation describes an example of attaching an indoor dome type WV-S2131L model.
  For how to install the camera, refer to the instructions for installation in the Operating Instructions for each model.
  Step 3 Attach the pipe fitted to this product (used on camera) in Step 1, to this product (used on ceiling) fitted to the ceiling in Step 2.

•  Tighten the screw section of the pipe for fixing the pipe securely to this product (used on ceiling). Failure to observe this may cause a drop resulting in accidents.

Step 4 Attach the attachment plate to this product (used on camera).

1. Fix the snap hook of the safety wire to the wire hook section on this product (used on camera).
2. Fix the attachment plate (camera accessory) to this product (used on camera).
   Recommended tightening torque : 0.78 N·m {0.58 lbf·ft}

Step 5 Connect the cables to the camera.
For how to connect and other details, refer to the Operating Instructions for each camera.

• The “recommended tightening torque” values shown hereon for the different screws used in mounting the camera are the values of the model used for the description in this manual.
  Check the Operating Instructions of the camera you are using and confirm the values.

Step 6 Temporarily fix the camera to the attachment plate and tighten the camera fixing screw (red) to fix the camera firmly.

• Be sure to tighten the camera fixing screw. Failure to observe this may cause camera trouble due to camera falling.
  Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

NOTE

•  You can change the angle of mounting the camera to the attachment plate in units of 90 degrees, as necessary.

Step 7
After adjusting the angular field of view of the camera, fix the enclosure to the original poisition.
Refer to the Installation Guide for the camera for detailed adjustment methods.

NOTE

• The recommended tightening torque for the screws depends on the camera you are using. Refer to the Installation Guide for each camera.

Step 8 Attaching the compact dome type WV-S31xx series

1.  Install according to the description in Steps 2 and 3.
2. Fix the snap hook of the safety wire to the wire hook section of this product (used on camera) according to the description in Step 4 1. (There is no attachment plate fitting work.)
3.  Connect the network cable and fix the camera to this product (used on camera). Attach the camera in such a way that the opposite side of the wire hook section of this product (used on camera) is towards the front of the camera. You can fix the camera pointing the front of the camera tilted at 30 degrees to the left or right. Recommended tightening torque : 0.78 N·m {0.58 lbf·ft}

IMPORTANT

• When fixing a compact dome type camera, it can be fixed in only the 2 directions illustrated above. If the photographing area cannot be adjusted with these 2 directions and PAN rotation, invert the mounting direction of this product (used for the ceiling) by 180 degrees.

NOTE

• When fixing a compact dome-type camera, of the three fixing positions, use the 2 forward places to fix.

For U.S. and Canada:
i-PRO Americas Inc.
For Europe and other countries:
i-PRO EMEA B.V.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022 Fs0320-3042
Printed in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>