SolidRun SRG0400 SolidSense Compact Gateway Installation Guide

SRG0400 Solid Sense Compact Gateway
Installation Guide Installation Sheet

Solid Run Solid Sense Compact

The IoT Gateway is a multi-protocol gateway that can simultaneously receive data from multiple wireless protocols. It is designed for commercial facilities and building installations. The Gateway has built-in radios to allow for direct  communication with sensors in the IoT Sensor Solution product family. Multiple gateways can be installed to support thousands of sensors.

Regulatory Compliance and Safety Information

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Solid Run for any consequences arising out of the use of this material.
Carefully read these instructions and all information relevant to this product before trying to install it. See the list of technical literature.

Dimensions

Installation Restrictions

NOTICE
REDUCED DEVICE PERFORMANCE

• This device is for indoor use only and is not suitable for wet locations.
• Do not install the device close to an exterior window.
• When replacing a device, install the new device in the same position and direction as the replaced device.
  Failure to follow these instructions can result in reduced device performance.

Installing the Device

1. For models with LTE option: Install the antenna a.
2. Use adapted screws to install the gateway on the wall.
3. Power on the gateway using the power adapter a or Power over Ethernet (PoE).
   The green LED will turn on solid to indicate the device is operational. Otherwise, press the on/off button to power it up.

Connections and Buttons

Part Numbers

General Specifications

Maximum number of supported devices
IoT Sensor Solution sensors
200
Material
Enclosure
Plastic casing with internal antenna for Wi-Fi/
Bluetooth. One SMA port for LTE.
Mechanical
Dimensions
150L x 85W x 40H mm (5.9L x 3.3W x 1.6H in)Weight
185 g (0.4 lb)
Electrical
Power
DC 9 – 36 V
Power over Ethernet (PoE) PD IEEE802.3AF
5W peak power
Hardware
RAM
1GB DDR4
Storage capacity
8GB eMMC| Connectors
1 x RS485 (option)
1 x CAN (option)
1 x USB 2.0 Connector, Type-A
1 x DC 9V – 36V power supply
Wireless connectivity
Communication protocol
2.4 GHz, Sensor Network supporting Mesh
Technology
Antenna type
Omnidirectional, internal.
WiFi Interface
2.4GHz/5GHz b/g/n/ac
module
Antenna type
Omnidirectional, internal.
FCC ID: 2BA24LBEE5HY1MW,
IC: 12107A-LBEE5HY1MW
LTE (Optional)
1 x LTE Cat 4 Worldwide + GPS (with fallback
on 3G/2G)
FCC ID: XMR201903EG25G
IC: 10224A-201903EG25G| Optional AC/DC Power supply
Model ICP12-120-1000D
Input AC 100-240V
Output DC 12V-1A @ 40°CEnvironment
Environmental conditions
Indoor use only
Ambient temperature, operating
0 to 50 °C (32 to 122 °F)
Ambient temperature, storage
-20 to 65 °C (-4 to 149 °F)
Humidity
0 to 95 % (non-condensing)
Installation
Mounting
Wall-mounted
Installation equipment, included
Mounting tape, screws, installation instructions
---|---|---

FCC ID: 2BA240-SRG0400, IC: 12107A-SR0400
Addendum – California Proposition 65 Warning Statement for California Residents

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm, and Bisphenol A (BPA), which is known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

 (This table is made according to SJ/T 11364.)
(Indicates that the concentration of hazardous substance in all of the homogeneous materials for this part is below the limit as stipulated in GB/T 26572.)
(Indicates that the concentration of hazardous substance in at least one of the homogeneous materials used for this part is above the limit as stipulated in GB/T 26572.)

Regulatory Notices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated with minimum distance 20 cm (7.9 inches) between the antenna and your body during normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-003(B) / NMB-003 (B).
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.9 inches) between the radiator and any part of your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This radio transmitter IC: 12107A-SRG0400 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Under Innovation, Science and Economic Development regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Approved Antenna Type:

© 2022 Solid Run Ltd .
All rights reserved.
Trademarks and registered trademarks are the property of their
respective owners. www.se.com/buildings

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>