i-PRO WV-S2570L Network Camera Installation Guide
- June 13, 2024
- i-PRO
Table of Contents
Installation Guide
Included Installation Instructions
Network Camera
Model No. WV-S2570L
WV-S2570L Network Camera
- Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
- For information about the basic description of this product, refer to the Important Information on the provided CD-ROM. For information about how to perform the settings and how to operate the camera, refer to the Operating Instructions on the following our support website. https://i-pro.com/global/en/surveillance/documentation_database
- Before reading this manual, be sure to read the Important Information.
Important safety instructions
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Only use attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has een exposed to rain or moisture, does not operate normally, or has been dropped.
Troubleshooting
Before requesting service, refer to “Troubleshooting” of Important Information in the CD-ROM and Operating Instructions on our support website. Then, confirm the trouble.
Open Source Software
- This product contains open source software licensed under GPL (GNU General Public License), LGPL (GNU Lesser General Public License), etc.
- Customers can duplicate, distribute and modify the source code of the software under license of GPL and/or LGPL.
- Refer to the “readme.txt” file on the provided CD-ROM for further information about open source software licenses and the source code.
- Please note that we shall not respond to any inquiries regarding the contents of the source code.
Caution:
- A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.
- ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).
WARNING:
- To prevent injury, this apparatus must be secur ely attached to the wall/ceiling in accordance with the installation instructions.
- All work r elated to the installation of this pr oduct should be made by qualified service personnel or system installers.
- The installation shall be carried out in accordance with all applicable installation rules.
- The connections should comply with local electrical code.
- Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunlight, fire or the like.
CAUTION:
- The network camera is only intended for a con- nection to an ethernet or PoE network without routing to the outside plant.
For Canada
CAN ICES-3(A)/NMB-3(A)
For U.S.A.
The model number and serial number of this product may be found on the surface
of the unit.
You should note the model number and serial number of this unit in the space
provided and retain this book as a permanent record of your purchase to aid
identification in the event of theft.
Model No………………….
Serial No………………….
**** : Direct current symbol
For U.S.A.
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Supplier’s Declaration of conformity
Trade name : i-PRO
Model No. : WV-S2570L
Responsible Party :
i-PRO Americas Inc.
8550 Fallbrook Drive, Suite 200 Houston,
Texas 77064
Support Contact : 1-800-513-5417
For U.S.A. and Canada
This device complies with part 15 of FCC Rules and Innovation, Science and
Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions : (1)This device may not
cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
** These symbols on the products, packaging, and/or accompanying documents
mean that used electrical and electronic products and batteries must not be
mixed with general household waste.
For proper treatment, recovery and recycling of old products and used
batteries, please take them to applicable collection points in accordance with
your national legislation.
By disposing of them correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local
authority. Penalties may be applicable for incorrect disposal of this waste,
in accordance with national legislation.
Note for the battery symbol (bottom symbol)**
This symbol might be used in combination with a chemical symbol. In this case
it complies with the requirement set by the Directive for the chemical
involved.
About the user manuals
Product documentation is composed of the following documents.
- Installation Guide (this document): Explains installation, mounting, cable connections, and adjusting the fi eld of view.
- Important Information (included in the CD-ROM): Provides basic information about the product such as Precautions for installation, Parts and functions, etc..
- Operating Instructions (on our support website): Explains how to perform the settings and how to operate this camera.
“<Control No.: C**>” used in this document should be used to search for
information on our support website and will guide you to the right
information.
Note:**
- The exter nal appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.
Standard accessories
Installation Guide (this document) ………………….. 1 pc.
IMPORTANT SAFETY INSTRUCTIONS …………… 1 pc.
CD-ROM1 …………………………………………………. 1 pc.
Code label2 ……………………………………………….. 1 pc.
- The CD-ROM contains the several kind of operating instructions and different kinds of tool software programs.
- This label may be required for network management. Use caution not to lose this label.
The following parts are used during installation procedures.
Base bracket ……………………………………………… 1 pc.
Attachment plate ………………………………………… 1 pc.
Fixing screws for attachment plate
(M4 × 8 mm {5/16 inches}) …………………………..5 pcs.
(of them, 1 for spare)
Template A (for the attachment plate) ……………1 sheet
Template B (for the base bracket) ………………..1 sheet
Waterproof tape ………………………………………….. 1 pc.
RJ45 waterproof connector cover …………………. 1 pc.
RJ45 waterproof connector cap ……………………. 1 pc.
Bit (Hex wrench, screw
size 6.35 mm {1/4 inches} T20) ……………………….. 1 pc.
4P alarm cable …………………………………………… 1 pc.
2P power cable ………………………………………….. 1 pc.
MONITOR OUT conversion plug ……………………. 1 pc.
| Waterproof tape
---|---
| Bit
| MONITOR OUT conversion plug
Preparations
Prepare the required parts for each installation method before starting the installation. The following are the requirements for the various installation methods.
IMPORTANT:
- For information about the minimum pull-out strength, refer to our website (https://i-pro.com/global/en/surveillance/training_support/support/technical_information Control number:C0120>).
- Procure 4 screws (M4) to secure the attachment plate (accessory) or the base bracket (accessory) to a ceiling or a wall.
- The minimum required pull-out capacity of a single screw or anchor bolt is 196 N {44 lbf} or more when mounting with the installation method 【Type 1】, 【Type 2】, or 【Type 3】 described in the right table.
- Select screws according to the material of the location that the camera will be mounted to. In this case, wood screws and nails should not be used.
- If the mounting location such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced.
- This product can only be installed indoors when WV-Q105A or WV-Q169A is used to install it on the ceiling.
| Installation method | Description of installation method |
|---|
Mount the camera on the two-gang junction box using the attachment plate
(accessory).| [Type 11
Directly mount the camera onto the ceiling or wall using the attachment plate
(when wiring can be installed in the ceiling or wall).| [Type 2]
Mount the camera onto the ceiling or wall using the base bracket (accessory)
(when conduits are used for wiring, or when there is no space available for
wiring in the ceiling or the wall).| [Type 3)
Mount the camera on the ceiling or wall by combining of the optional bracket.
Refer to our website
https://i-pro.com/globa/en/surveillance/training_suppor/support/technical_information
Installation
The installation tasks are explained using 5 steps.
Step 1 Fixing the brackets (There are 3 methods to install the camera to a ceiling or wall.)
【Common】
Note:
- Attach the attachment plate (accessory) so that the marking (part number) faces toward the ceiling or wall to be installed.
【Type 1】Mount the camera on the two-gang junction box using the attachment
plate (accessory).
Fixing screws for attachment plate (4pcs) (M4:
locally procured)
【Type 2】Directly mount the camera onto the ceiling or wall using the
attachment plate (accessory).
Align the FRONT direction of the template A (accessory) with the desired
direction, and drill through four holes to attach the attachment plate and a
25.4 mm {1 inch} diameter hole to pass through the cables. Then, attach the
attachment plate to the ceiling or wall. The direction of the marker “FRONT⇩”
on the camera (see the figure in [4] of “Step 3 Mount the camera”) should face
the desired direction of the camera.
-
-
If the mounting direction of the camera is not determined yet or if you want to change the direction of the camera after it has been installed
If you want to be able to change the direction of the camera, drill through a 73 mm {2-7/8 inches} diameter hole in the center. By doing so you can adjust the mounting direction of the camera in 90° increments.
【Type 3】Mount the camera to a ceiling or a wall using base bracket (accessory).
-
Using the template B (accessory), make screw holes for fixing the base bracket and wiring holes.
The base bracket can be fixed in any of the following 6 screwing positions according to ceiling and wall conditions. Match the hole used when installing the camera to any of positions A to F.
-
Select any of the two wiring holes of template B (accessory) when installing the base bracket. After mounting the attachment plate, the mounting direction of the camera can be adjusted in 90° increments.
-
When attaching the base bracket to a one-gang junction box in Position E, secure the base bracket with 2 screws (M4, locally procured).
When using the conduit on the ceiling or wall for wiring, remove the cap for
the female thread for the conduit by using a hexagon wrench (ISO 2936, width
across flats S=5 mm {3/16 inches}).
The female thread for conduit is compliant with ANSI NPSM (parallel pipe
threads) 3/4 or ISO 228-1 (parallel pipe threads) G3/4. Mount the base bracket
and the attachment plate.
- If open wiring is conducted, be sure to use conduits and run the cables inside the tubes to protect the cables from direct sunlight.
- Installation work shall be such that there is no exposure to water into the architecture through the conduits having been joined..
Step 2 Making connections
- Refer to the Important Information on the provided CD-ROM for details about each cable.
IMPORTANT:
- Turn off each system’s power supply (PoE hub or device to supply power to the camera) before making a connection.
- The 12 V DC power supply shall be insulated from the commercial AC power.
【1】Connect an Ethernet cable (category 5e or better, straight) to RJ45
network cable.
The maximum cable length is 100 m {328 feet}.
-
First pass the Ethernet cable through the RJ45 waterproof connector cap (accessory) and then through the RJ45 waterproof connector cover (accessory). Next, use a specialized tool (locally procured) to crimp the RJ45 plug (locally procured) to the end of the Ethernet cable.
• Take care not to remove the rubber parts from inside the RJ45 waterproof connector cover. -
Insert the RJ45 plug into the RJ45 waterproof jack connected to the camera.
-
Insert the RJ45 waterproof connector cover so that the “◁: OPEN” mark aligns with the “▶” mark of the RJ45 waterproof jack, and rotate in the direction of the arrow in the illustration at right until matching with the“⇦: LOCK” mark.
-
Connect the RJ45 waterproof connector cap to the RJ45 waterproof connector cover and rotate the RJ45 waterproof connector cap until there is no gap between it and the RJ45 waterproof connector cover.
IMPORTANT:
- If the procedure for the RJ45 waterproof connector (accessory) part is not correctly followed, the waterproofing may be compromised. Do not install the camera where the RJ45 waterproof connector is exposed to constant rain or moisture.
- The external dimensions of the Ethernet cable are from ø5 mm {ø3/16 inches} to ø6.5 mm {ø1/4 inches}.
- When removing the RJ45 waterproof connector, be sure to loosen the RJ45 waterproof connector cap first, rotate the RJ45 waterproof connector cover in the direction opposite to the attaching direction, and remove it. (If the RJ45 waterproof connector cover is removed when the “⇦: LOCK” mark of the RJ45 waterproof connector cover is aligned with the “▶” mark of the RJ45 waterproof jack, the RJ45 waterproof jack may be damaged).
【2】When connecting an AC adaptor or an external power supply, use the 2P power cable (accessory) to connect it to the camera.
Connect the output cable of the AC adaptor to the 2P power cable (accessory).
(Red: 12 V DC side, Black: GND side)
【3】If needed, connect the 4P alarm cable (accessory).
4P alarm cable (accessory)
Note:
- The default of EXT I/O terminals are “Off”. Refer to the Operating Instructions on our support website for further information about the EXT I/O terminal settings.
【4】If needed, connect a microphone or the line out of an external device to
the audio input cable.
【5】If needed, connect a powered speaker to the audio output cable.
【6】Adequate waterproof treatment is required for the cables when installing
the camera with cables exposed.
The camera body and RJ45 waterproof connector are waterproof, but the cable
ends and the internal part of the base bracket (accessory) are not waterproof.
When using cables other than Ethernet cables, apply waterproof treatment on
each connecting part including disused cables as shown below.
IMPORTANT:
- Stretch the tape by approx. twice (see the illustration) and wind it around the cable. Insufficient tape stretch causes insufficient waterproofing.
Step 3 Mount the camera
-
Align the OPEN mark of the side of the camera with the protruding part of base bracket, insert 2 attachment mounting screws into the attachment plate, and rotate the camera approximately 15°. The LOCK mark is moved to the protruding part of base bracket and the camera is temporarily secured. (When directly attaching the attachment plate to a ceiling or wall, align the OPEN mark to the nail of the attachment plate.)
IMPORTANT:
● For installation on the wall, install the camera with the ventilation opening in a sideways or downward position. In a face-up position, the ventilation opening doesn’t work well as water accumulates on the surface. -
Loosen 4 enclosure fixing screws using the bit (accessory), and remove the enclosure from the camera.
IMPORTANT:
● Enclosure is fixed to the camera body by the installed auxiliary wire, so please do not remove it. -
Secure the camera by tightening the camera fixing screw (red).
IMPORTANT:
● Be sure to tighten the camera fixing screw. Failure to observe this may cause camera trouble due to camera falling. (Recommended tightening torque: 0.78N·m {0.58 lbf·ft}) -
Loosen the cross-head side of TILT table fixing screw (on one side), and incline the TILT table while keeping the TOP mark on the camera lens head facing the front (i.e. the direction of FRONT⇩ mark on the camera).
● A part of the enclosure and the auxiliary wire is omitted in the illustrations after this section. -
Connect the MONITOR OUT conversion plug (accessory) to the MONITOR OUT terminal of the camera, and then connect the monitor for adjustment with cable (locally procured).
-
Insert an SD memory card into the SD slot, if necessary.
● Refer to the “Important Information” on the provided CD-ROM for how to insert/remove the SD memory card.
Step 5 Configure the network settings
Download and start [IP Setting Software]
For U.S. and Canada:
i-PRO Americas Inc.
https://www.i-pro.com/
For Europe and other countries:
i-PRO Co., Ltd. Fukuoka, Japan
https://www.i-pro.com/
i-PRO EMEA B.V. UK Branch
1010 Cambourne Business Park,
Cambridgeshire CB23 6DP
**** Authorised Representative in EU:
i-PRO EMEA B.V.
Laarderhoogtweg 25, 1101 EB
Amsterdam, Netherlands