inverto IDLM-SINM410-TRPMN-8PN Single Triple-feed Monoblock LNBs User Manual

inverto IDLM-SINM410-TRPMN-8PN Single Triple-feed Monoblock LNBs

PRODUCT INFORMATION

General Information:
Please read the information contained in this manual before installing the LNB. The operations described in the instructions must be carried out in the order presented.

Product Description:
The Monoblock LNB is designed to be used with a satellite dish antenna equipped with a 40mm LNB holder for mounting. It allows receiving satellite signals in the Ku band.

Installation & Safety:

• Warning! The LNB and the satellite dish antenna should be installed by a qualified satellite antenna installer and in compliance with safety regulations.
• Do not install the LNB during a storm or other extreme weather conditions.
• Connect the coaxial cable to the LNB before connecting the set top box.
• Carry out your satellite dish and LNB installation with tools and accessories intended for this purpose only.

Installing the LNB on the dish antenna:

1. Place the LNB in the LNB holder/clamp of the dish antenna. Close the LNB holder handle and lightly tighten the clamp screw so that the LNB can still rotate.
2. Set the correct tilt angle of the LNB by rotating it clockwise or counterclockwise. The tilt angle of the LNB depends on the location of the satellite dish antenna installation and the satellite to adjust. Turning should be done using a satellite signal meter or a satellite receiver measurement indications.
3. After determining the correct position of the LNB, tighten the screws that secure the LNB clamp so that the LNB is fixed in its place.
4. The above description of the LNB installation applies to the case when the satellite dish is correctly installed and aligned towards the desired satellite. In other cases, you must complete the installation and correct alignment of your satellite dish first.
5. We strongly recommend that the satellite dish antenna is installed by a qualified satellite antenna installer.

Connecting the antenna cable to the LNB:

1. Attach the protective rubber boot to the antenna cable.
2. Strip the cable insulation and screw the F-plug onto the end of the cable.
3. Make sure the braided wires and the center conductor are not touching each other as this degrades signal quality.
4. Screw in the F-plug to connect the antenna cable to the LNB.
5. Slide the protective rubber boot into its collar tip at the LNB housing.

Technical data:

Note: Product images are for illustrative purposes only and may  differ from the actual product.

Simplified EU Declaration of Conformity:
A copy of the full text of the EU declaration of conformity can be found at: www.inverto.tv/support_dc

Models

• 6053 Single Triple-feed Monoblock 23mm LNB for 85cm dish with 40mm adapters 13°E (SAT B) + 16°E (SAT A) + 19.2°E (SAT C) IDLM-SINM410-TRPMN-8PN
• 6050 Quad Monoblock 23mm LNB ,3° for 80cm dish with 60mm adaptor 13.0°E (SAT A) + 16.0°E (SAT B) IDLM-QDM610-MNOO3-8PN
• 6049 Quad Monoblock 23mm LNB ,3° for 80cm dish with 40mm adaptor 13.0°E (SAT A) + 16.0°E (SAT B) IDLM-QDM410-MNOO3-8PN
• 5991 Twin Monoblock 23mm LNB ,4.3° for 80cm dish with 40mm adaptor 19.2°E (SAT A) + 23.5°E (SAT B) IDLM-TWM410-MNO43-8PN
• 5990 Twin Monoblock 23mm LNB ,3° for 80cm dish with 40mm adaptor 13.0°E (SAT A) + 16.0°E (SAT B) IDLM-TWM410-MNOO3- 8PN
• 5989 Twin Monoblock 23mm LNB ,3° for 80cm dish with 60mm adaptor 13.0°E (SAT A) + 16.0°E (SAT B) IDLM-TWM610-MNOO3- 8PN
• 5988 Single Monoblock 23mm LNB ,3° for 80cm dish with 60mm adaptor 13.0°E (SAT A) + 16.0°E (SAT B) IDLM-SIM610-MNOO3-8PN

General Information

• Please read the information contained in this manual before installing the LNB.
• The operations described in the instructions must be carried out in the order presented.

Product Description

• The LNB is intended for use with a satellite dish antenna equipped with a 40mm LNB holder for mounting.
• The LNB allows receiving satellite signals in the Ku band.

Installation & Safety

Warning! The LNB and the satellite dish antenna shall be installed by a qualified satellite antenna installer, and in compliance with safety regulations.

• Do not install the LNB during a storm or other extreme weather conditions.
• Connect the coaxial cable to the LNB before connecting the set top box.
• Carry out your satellite dish and LNB installation with tools and accessories intended for this purpose only.

Installing the LNB on the dish antenna

1. Place the LNB in the LNB holder/clamp of the dish antenna. Close the LNB holder handle and lightly tighten the clamp screw so that the LNB can still rotate (Fig. 1).
2. Set the correct tilt angle of the LNB by rotating the LNB clockwise or counterclockwise: The tilt angle of the LNB (K) depends on the location of the satellite dish antenna installation and the satellite to be received. For example, for receiving Hotbird at 13°E in Warsaw, the tilt angle of the LNB should be 6° counterclockwise. Fine angle adjustment turning should be done using a satellite signal meter or a satellite receiver measurement indications (Fig. 2).
3. After determining the correct position of the LNB, tighten screws that secure the LNB clamp so that the LNB is fixed in its place (Fig. 3).
4. The above description of the LNB installation applies to the case when the satellite dish is correctly installed and aligned towards the desired satellite. In other cases, you must complete the installation and correct alignment of your satellite dish first.
5. We strongly recommend that the satellite dish antenna is installed by a qualified satellite antenna installer.
   Note: Product images are for illustrative purposes only and may differ from the actual product.

Connecting the antenna cable to the LNB

1. Attach the protective rubber boot to the antenna cable.
2. Strip the cable insulation and screw the F-plug* onto the end of the cable (Fig. 4).
3. Make sure the braided wires and the center conductor are not touching each other as this degrades signal quality.
4. Screw in the F-plug to connect the antenna cable to the LNB.
5. Slide the protective rubber boot into its collar tip at the LNB housing.

Technical data

Simplified EU Declaration of Conformity

• FTA Communication Technologies S.á r.l hereby declares that the LNB converter type 5988/5989/5990/5991 /6049/6050/6053 meets the essential requirements of the following directives:
  • RED 2014/53 / EU
  • RoHS 2011/65 / EU
• A copy of the full text of the EU declaration of conformity can be found at: www.inverto.tv/support_dc

WEEE Notice

• Environmental protection is an important objective of our company.
• The crossed out waste container means that this product cannot be disposed of as waste after it has ended from the household, but must be disposed of in a special place. We hereby inform you that the main purpose of the regulation European and the Act of 11 September 2015 on waste electrical and electronic equipment is to limit the amount of waste arising from equipment, ensuring an appropriate level of collection, recovery and recycling of used equipment, and increasing public awareness of its harmfulness to the natural environment at every stage of its use. Pursuant to art. 36 above of the Act, the user of equipment intended for households is obliged to return used equipment to the collector waste equipment or the entity authorized to collect waste equipment referred to in art. 45 item 1 point 1 of the Act of December 14 2012 on waste. With all this in mind, it should be stated that in the above process, households have to meet very important role. However, it should be remembered that products belonging to the group of electrical or electronic equipment should be utilized in the right way and in the right places. Information on local collection points (storage site, collection point, etc.) can be provided by local authorities or the distributor.
• At the same time, it should be emphasized that distributors are obliged to take back waste equipment from households free of charge at the point of sale, provided that the waste equipment is of the same type and performed the same functions as the equipment sold. In addition, the distributor, providing the buyer with equipment intended for households, is obliged to take back free used equipment from households at the place of delivery of that equipment, provided that the waste equipment is of the same type and has the same functions as the equipment supplied. In this way you can participate in the process of reusing raw materials and supporting the electrical and electronic waste management program, which may affect environment and public health. It should be remembered that the correct disposal of equipment allows saving valuable resources and avoiding negative effects on health and the environment, which may be threatened by inappropriate handling of waste and components dangerous.

Importer

• FTA Communication Technologies S.à r.l
• 17 Route de Luxembourg, Gonderange L-6182

For further details contact:

• sales@inverto.tv
• FTA Communication Technologies S.á r.l
• Tel. +352 264 367 1
• Fax. +352 264 313 68
• 17 Route de Luxembourg, Gonderange, L-6182, Luxembourg

References

• Product Support - Inverto.tv

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>