MOLDEX 2400 Classic Non Valved Disposable Respirator Mask Instruction Manual
- June 13, 2024
- MOLDEX
Table of Contents
MOLDEX 2400 Classic Non Valved Disposable Respirator Mask
Product Information
- Product Model: Classic, Smart, Smart Active, Smart Pocket, Smart Solo, Air
- Product Certification: EU 2016/425 EN 149:2001
- Additional Standards: EN 149:2001 + A1:2009
- Manufacturer: Moldex
- Manufacturer Website: www.moldex-europe.com/conformity
- Use-by Date: 0121 (January 2021)
- Manufacturer Address: GB 9 Glaisdale Point Bilborough, Nottingham NG8 4GP
Product Usage Instructions
- Ensure the product is suitable for your specific model (Classic, Smart, Smart Active, Smart Pocket, Smart Solo, Air).
- Verify that the product meets the certification standard EU 2016/425 EN 149:2001.
- Check for compliance with additional standards EN 149:2001 + A1:2009.
- Refer to the Moldex website for conformity information and further details on the product.
- Use the product before the specified use-by date (0121 – January 2021).
- Contact Moldex at GB 9 Glaisdale Point Bilborough, Nottingham NG8 4GP for any queries or concerns.
Instructions for use Use
Protects from solid and liquid aerosols to EN 149:2001+A1:2009 NR: for single
use, dispose at end of shift.
D: Dolomite clogging test passed. Queries? Contact your safety officer or
Moldex. To select the right respirator and protection level observe national
regulations. Check before use/fitting See pictograms on box. Use mask only if
not damaged. Perform a fit check: Cover the mask with both hands and exhale
sharply. If leakage is detected, check position of mask – if necessary shorten
strap. Only enter workplace when proper fit is achieved.
Note: Facial hair can prevent adequate fit. Warning The wearer must be instructed in the proper use of the mask. No metal parts that can cause sparks in explosive atmosphere. Does not protect the wearer against gases / vapours, or atmospheres with less than 19.5% oxygen. Do not enter unventilated narrow rooms and shafts with filtering face pieces. Do not use against contaminants / concentrations unknown or immediately dangerous to health. Leave area immediately when breathing becomes difficult or other distress occurs. Dispose respirator when damaged or breathing resistance increases strongly. Never modify or tamper with mask. Incorrect use or not following the user instruction can reduce the protection level and lead to damage to health. Storage see pictograms
EU declaration of conformity
EU declaration of conformity www.moldex-europe.com/conformity
800-561-5885 or sales@samlexsolar.com. Product Usage Instructions To use the Samlex solar accessories, follow the instructions below: ADJ-28 (Adjustable Solar Panel Tilt Mount): Attach the 2 x 28 Mounting Rails to a suitable base for support. Attach the solar panel to the 2 x 28 Mounting Rails using the provided brackets, carriage bolts, and wing nuts. Adjust the tilt angle of the solar panel using the 2 x 14 Aluminum Brackets. Ensure the solar panel is securely mounted and tilted for optimal sun exposure. SBC-2-DC (Branch Connectors): Identify the panels you want to connect in parallel. Snap-in one female connector of the Branch Connector to the positive terminal of one panel. Snap-in one male connector of the Branch Connector to the positive terminal of the other panel. Repeat the above steps for the negative terminals of the panels using the remaining female and male connectors. Ensure all connections are secure and sealed against dust and water ingress. MC4-2 (Multi-Contact Connectors): Identify the panels you want to connect in series. Snap-in one female connector of the Multi-Contact Connector to the positive terminal of one panel. Snap-in one male connector of the Multi-Contact Connector to the positive terminal of the other panel. Repeat the above steps for the negative terminals of the panels using the remaining female and male connectors. Ensure all connections are secure and sealed against dust and water ingress. SCW-20-2 (Connecting Wires): Identify the desired connection between a solar panel and a charge controller or an additional panel. Connect the female connector of the Connecting Wire to the positive terminal of the solar panel. Connect the male connector of the Connecting Wire to the corresponding positive terminal of the charge controller or additional panel. Ensure a secure connection is made with both connectors. SM5-KIT (Mounting Brackets & Hardware): Select a suitable flat surface for mounting the solar panel. Securely attach the four Mounting Brackets to the flat surface using the provided hardware. Place the solar panel on top of the Mounting Brackets, ensuring it is properly aligned and centered. Ensure the solar panel is securely mounted with sufficient space underneath for cooling. Do you already have a solar panel but need a mounting system? Maybe you have a connecting wire but need to replace a contact? Either way, we’ve got you covered. Samlex mounting systems, connecting wires and connectors are sold separately. Solar Accessories Models ADJ-28 SBC-2-DC MC4-2 SCW-20-2 SM5-KIT MODEL NO.: DESCRIPTION: CONTAINS ADJ-28 ADJUSTABLE SOLAR PANEL TILT MOUNT Aluminum adjustable solar mounts allow you to tilt your panel for optimal sun exposure Weather resistant aluminum construction Over 30 adjustable settings between 0-90o! Get up to 40% more out of your solar panel SBC-2-DC BRANCH CONNECTORS Easy to install “Snap-in” type of safety locking tabs Contacts are sealed against ingress of dust and water Connects panels in parallel Use to expand SRV kits with SSP panels Packaged in pairs, female & male per package MC4-2 MULTI-CONTACT CONNECTORS Easy to install “Snap-in” type of safety locking tabs Contacts are sealed against ingress of dust and water Connect panels in series Packaged in pairs, female & male per package SCW-20-2 CONNECTING WIRES Connect your panel to a charge controller or to an additional panel Pair of 20 ft connecting wires 1 male & one female connector SM5-KIT MOUNTING BRACKETS & HARDWARE Aluminum Adjustable Solar Mounts Secures the solar panel to a flat surface Provides space underneath for cooling Packaged in fours 4 brackets & hardware NOTE: Specifications are subject to change without notice 12013-Solar Accessories-0823 To view a full selection of Samlex products visit our website at samlexsolar.com or contact us: 1-800-561-5885 or sales@samlexsolar.com" width="961" height="194" srcset="https://manuals.plus /wp-content/uploads/2023/09/MOLDEX-2400-Classic-Non-Valved-Disposable- Respirator-Mask-1.png 961w, https://manuals.plus/wp- content/uploads/2023/09/MOLDEX-2400-Classic-Non-Valved-Disposable-Respirator- Mask-1-550x111.png 550w, https://manuals.plus/wp- content/uploads/2023/09/MOLDEX-2400-Classic-Non-Valved-Disposable-Respirator- Mask-1-768x155.png 768w" sizes="(max-width: 961px) 100vw, 961px" />
- Storage maximum relative humidity
- Storage temperature range
- End of shelf life
- Read user instruction
EU type certification and Conformity assessment:
IFA (0121), 53757 St. Augustin, DE
DE Head Office GB 9 Glaisdale Point
Tübinger Straße 50 Bilborough, Nottingham NG8 4GP
72141 Walddorfhäslach
Moldex/Metric AG & Co. KG
www.moldex-europe.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>