i-PRO WV-QWD100C-W Wall Mount Bracket Instruction Manual

i-PRO WV-QWD100C-W Wall Mount Bracket

• Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.
• i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
• “<Control No.: C****>” used in these documents should be used to search for information on our technical information website
  (https://i-pro.com/global/en/ surveillance/training-support/support /technical-information) and will guide you to the right information.

Precautions

• Do not use this bracket except with suitable cameras.
  Failure to observe this may cause a drop resulting in injury or accidents.

• Refer installation work to the dealer.
  Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.

• The measures of protection against a fall of this product shall be taken. Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety wire.

• The screws and bolts must be tightened to the specified torque. Failure to observe this may cause a drop resulting in injury or accidents.

• Install the product securely on a wall in accordance with the installation instructions. Failure to observe this may cause injury or accidents.

• Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury. When using this product, also read the “Precautions” described in the operating instructions for the camera to be attached.

About notations

Some functions are expressed with the following notations in this document.

• Clear dome cover
• Smoke dome cover

Preface
This product is a wall mount bracket that is designed to mount the indoor PTZ type camera on a wall.

Specifications

• Ambient temperature: –10 °C to +50 °C {14 °F to 122 °F}
• Dimensions: 165 mm (W) x 206.5 mm (H) x 217.5 mm (D) {6-1/2 inches (W) x 8-1/8 inches (H) x 8-9/16 inches (D)}
• Mass: Approx. 950 g {2.10 lbs.}
• Finish: Main body: Surface treatment steel sheet
• Top and bottom covers: ABS resin i-PRO white
• Dome cover: Acrylic resin

Precautions for installation

• In order to prevent injury, the product must be securely mounted to the wall according to the Installation Guide of this product.

This product is designed to be used indoors.
This product is not operable outdoors. Do not expose this product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this product away from water and moisture.

Installation area for this product
Make sure that the installation area is strong enough to hold the total weight of the camera assembly before installation.

• Make sure to remove this product if it will no longer be used.

Standard Accessories

• Operating Instructions (this book)………………..1 pc.
• The following are for installation.
• Template………………………………………………….1 pc.
• Inner cover (WV-QAT100)…………………………..1 pc.

Other items that are needed (not included)

IMPORTANT

• Minimum pullout strength: 196 N {44 lbf} (per 1 pc.)
• Refer to our technical information website for information on the minimum pull-out strength.
• Select screws according to the material of the location that the camera will be mounted to. In this case, wood screws and nails should not be used.

Parts and functions

If a tiepin type microphone is used, mount the microphone on the rubber-made microphone stand. Unless the microphone is used, cut the rubber with a nipper or conduct another treatment.
IMPORTANT : To prevent injuries and protect the cables, finish the notch with a file to avoid sharp edges.

Installation

Refer to the operating instructions of the camera for details on the camera installation (including the camera mounting, cable connection and adjustment).

Step 1: Put the template (accessory) against the wall and mark the positions of fixing screws and hole through which the cables run.

Drill 4 holes on the wall to secure it with M4 screws. The hole diameter shall be decided in accordance with the specifications of the screws and anchors to be used. If cables are routed inside the wall, bore a hole (ø60 mm {2-3/8 inches}) through the wall

Step 2: Remove the bottom cover from this product

1. Loosen the fixing screw (unremovable) to be used for cover fall prevention.
2. Pull down the bottom cover while pressing the marks (shown with 扌 in the drawing) to remove the cover.
   Note: Be aware that the inner cover is present in the bottom cover.

Step 3: Attach the inner cover.

1. Remove the side covers from the camera main body. (Both the left and right sides)
2. Attach the inner cover
   • When removing the inner cover
     Release the claws on the inner surface on both the left and right sides one by one and then remove the inner cover

Step 4: Mount the top cover on the wall and run the cables.

Fix the top cover with four screws. Screws are not provided. Prepare them in accordance with the camera installation position.

• Necessary screw: M4 (4 pcs.)
• Minimum pull-out strength: 196 N {44 lbf}

Step 5: Fix the camera and connect the safety wire.

1. Refer to the Installation. Guide of network camera for further information. The camera mount bracket is already attached to the top cover at the time of purchase. Make sure to use the pre-installed camera mount bracket.
   IMPORTANT: When mounting the camera, push the camera securely into the mounting section of the top cover.

2. Connect the safety wire locked on the top cover to the camera. Make sure that the apical ring of the safety wire is engaged with the safety wire hook of the camera by pulling the safety wire after connection.

Step 6: Mount the bottom cover

Be sure to push the bottom cover up until a click is heard.
IMPORTANT : Do not let the cables be caught during installation work.

Step 7: Tighten the fixing screw to be used for cover fall prevention.

Recommended tightening torque: 1.6 N·m {1.18 lbf·ft}

Step 8: Remove the protection sheet from the dome cover.

Note : When the tilt angle of the camera is almost level, the upper side of images will be hidden by this product reflecting on the screen. In such a case, adjust the tilt angle. Refer to the Operating Instructions of the camera for further information.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>