i-PRO WV-QEM502 Ceiling Mount Bracket Instruction Manual

i-PRO WV-QEM502 Ceiling Mount Bracket

• Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.
• i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
• “<Control No.: C****>” used in these documents should be used to search for information on our technical information website
  (https://i-pro.com/global/en/ surveillance/training-support/support /technical-information) and will guide you to the right information.

Caution: Before attempting to connect or operate this product, please read these instructions carefully.
Notice:

• This product is not suitable for use in locations where children are likely to be present.
• Do not install this product in locations where ordinary persons can easily reach.
• For information about screws and other parts required for installation, refer to the corresponding section of this document.

Precautions

• Do not use this bracket except with suitable cameras. Failure to observe this may cause a drop resulting in injury or accidents.

• Refer installation work to the dealer.
  Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.

• The measures of protection against a fall of this product shall be taken.

• Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety wire.

• The screws and bolts must be tightened to the specified torque. Failure to observe this may cause a drop resulting in injury or accidents.

• Install the product securely on a ceiling in accordance with the installation instructions. Failure to observe this may cause injury or accidents.

• Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury.

• When using this product, also read the “Precautions” described in the operating instructions for the camera to be attached.

Preface
This product is a ceiling embedded bracket that is designed to mount the network camera on a ceiling. This bracket can be used for an area with weak pull-out strength such as plasterboard in a double ceiling, and the embedded type makes the visible part of the camera smaller. The latest information about the supported cameras .

Specifications

• Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}
• Dimensions: ø212 mm × 134 mm (H) {ø8-11/32 inches × 5-9/32 inches} Including decorative cover thickness: 13 mm {1/2 inches}
• Mass: Approx. 740 g {1.63 lbs}
• Finish: Main body: Surface treatment steel sheet
• Decorative cover: ABS resin i-PRO white

Precautions for installation

• In order to prevent injury, the product must be securely mounted to the ceiling according to the Installation Guide of this product.
• This product is designed to be used indoors. This product is not operable outdoors. Do not expose this product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this product away from water and moisture.
• Installation area for this product Make sure that the installation area is strong enough to hold the total weight of the camera assembly before installation. The installation area shall have 210 mm {8-9/32 inches} or more space behind the ceiling. The thickness of the ceiling board for installation can range between 9 mm {11/32 inches} and 40 mm {1-9/16 inches}.
• Make sure to remove this product if it will no longer be used.

Standard Accessories

• Operating Instructions (this document)…….. 1 pc.

• Safety wire*………………………………………… 1 pc.

• Safety wire angle*………………………………… 1 pc.

• Fixing screw for attachment plate (M4 x 8 mm)…. 5 pcs.

• Template A…………………………………………. 1 pc.

• Template B…………………………………………. 1 pc.

• Decorative cover………………………………….. 1 pc.

• The product is shipped in a state where the safety wire is attached to the safety wire angle.

Other items that are needed (not included)

• Anchor bolt (M10)*……………………………….2 pcs.
• Nut (M10)…………………………………………. 6 pcs.

One anchor is used for securing the mounting chassis, and the other anchor is used for connecting the safety wire. (See Step2)

IMPORTANT : Prepare anchor bolts according to the material and strength of the area where the product is to be installed. The pull-out strength of the anchor bolt shall be more than 5 times of the total weight of the installed devices (including the camera body, ceiling mount bracket, anchor bolts, and all other parts).

Installation

Refer to the operating instructions of the camera for details on the camera installation (including the camera mounting, cable connection and adjustment).

Step 1: Put Template A (accessory) against the ceiling and make a hole.

1. Make 4 holes of 12 mm {15/32 inches} in diameter.
2. Remove the central part from the template.
3. Make a hole of 180 mm {7-3/32 inches} in diameter. The ceiling hole shape is shown in the drawing at right.

Step 2: Install two anchor bolts (M10: locally procured) into the ceiling.

1. Determine the anchor bolt length (for securing the mounting chassis) by use of Template B (accessory).
2. Position the nut (locally procured) by use of Template B and mount the nut. (The distance between the bottom surfaces of the ceiling board and nut shall be 134 mm {5-9/32 inches}.)

IMPORTANT: When the existing anchor bolt is used as an anchor bolt for connecting the safety wire, make sure that the distance between the anchor bolt and camera mounting position is 1 m {3.28 feet} or less.

Step 3: Secure the safety wire angle (accessory) to the anchor bolt (for connecting the safety wire), and connect the safety wire (accessory).

1. Mount a nut so that the safety wire angle is secured on the anchor bolt.
2. Remove the safety wire from the safety wire angle.
3. Insert the groove of the portion ❶ of the safety wire angle into the anchor bolt.
4. Close the safety wire angle while inserting the groove of the portion ❷ of the safety wire angle into the anchor bolt.
5. Connect the safety wire to the safety wire angle again.
6. Engage the nut from beneath, and secure the safety wire angle with top and bottom nuts.
7. Engage another nut from beneath to tighten and secure the nut that was engaged from beneath in y in a double nut fashion.

Note: When the existing anchor bolt that has been installed is used for connecting the safety wire, the use of 2 spacer nuts is helpful.

Step 5: Put the mounting hole of the mounting chassis on the anchor bol t

To align the i-PRO logo on the decorative cover, align the direction of the mounting chassis before inserting the mounting chassis into the mounting hole on the ceiling board. The direction of the i-PRO logo is indicated by a point that is shifted by around 10° from a point that is almost the exact opposite direction of the hook (to be used as the reference) that fixes the decorative cover

Step 6: Secure the mounting chassis.

1. Pass the upper side of the mounting chassis through the anchor bolt (for securing the mounting chassis).

2. Secure the mounting chassis to the ceiling board with the ceiling board fixing screws (4 places). Turning the ceiling board fixing screws clockwise provides ceiling board tightening between the bottom of the mounting chassis and ceiling board fixing bracket resulting in mounting chassis securing.
   Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
   IMPORTANT: When securing this bracket on the ceiling, make sure that the four ceiling board fixing brackets are open as shown in the right illustration.

3. Use double nuts (locally procured) to secure the mounting chassis.

Step 7: Mount the attachment plate.

Mount the attachment plate (accessory of the camera) to this mounting chassis. Use fixing screws for attachment plate (M4: accessory) to secure the attachment plate firmly as shown in the right illustration.
NOTE : Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

Step 8: Connect the cables and mount the camera on the attachment plate. Refer to the installation guide or the installation procedure leaflet of the camera for connection of cables and for how to fix the camera.

• Camera mounting method

Note: Hold and rotate the camera main body gently to the left to check that the lock plate of the camera does not come off.

• Camera dismounting method
  1.  Insert a thin flat head screwdriver to the gap between this product and the camera and lift up the lock plate.
  2. Turn the camera to the left in a state while the lock plate is being lifted up.

Step 9: Check the camera operation.
Remove the protection film and turn on the power of the camera. Then, check that the camera operation is normal.

Step 10: Mount the decorative cover.
Mount the decorative cover on this mount bracket.

• Align the “I” mark of the decorative cover (accessory) with the hook of the mounting chassis, press the decorative cover against the ceiling, and rotate the decorative cover clockwise when viewing it from beneath to secure the cover.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>