ALLCLEAR ACGL-001PE Smoke Detecting Alarm User Manual

ACGL-001PE Smoke Detecting Alarm
User Manual
Version: 01
Last Reviewed Date:  6/10/2022
Issued Date: 6/10/2022
Approved: Adam Gordon 6/10/2022
EN 14604:2005
AC:2008

Amendments

Introduction

The ACGL-0011DE Smoke detecting alarm is composed of a sophisticated analog circuit and digital circuit It is a low voltage, photoelectric, independent smoke alarm with a 3v lithium manganese battery. The alarm has a low power consumption, and the battery can last for up 10 years.

Features

✓ photoelectric smoke detection
✓ High sensitivity
✓ Local smoke alarm memory
✓ Normal detection mode and low sensitivity detection mode (hush )
✓ Built-in 10-year lithium/manganese battery (battery does not need to be replaced)
✓ 10 years life end warning tone
✓ low voltage warning tone
✓ low power consumption.

Technical Parameters

sound
Smoke detection or Key Test| LED (red) flashes and continuous alarm is given
Low sensitivity detection (Hush mode)| LED (red) flashes every 10 seconds, no alarm sound. automatically
cancel low sensitivity detection about 9 minutes later
Alarm memory| LED (green) flashes 3 times every 43 seconds and stops after 24 hrs. The first time you press test/mute button after alarm is activated, the detector will enter special alarm mode.
| | End of service life| After 10 years of active life the alarm will sound 3 times every 43 seconds. (Replace alarm with new device)
---|---|---|---
Low voltage inspect ron| LED (red) flashes once. alarm sound continuously for about 43 seconds
| Alarm loudness| ≥ 85d8/3m
| Working Temperature| -104°C – +40°C
| Ambient Humidity| 59596RH (no condensation)

Appearance

Dimensions

Activation

1. Remove the product and detach the base plate by turning anti clockwise

2. Turn the device over and you will see the battery pin is in the off position (figure 1)

3. To activate the device, slide the pin back and lock the top into the battery pin groove. (figure 2) The pin should sit flush with the back of the device.

4. Check the device is activated by checking the alarm indicator light (red LED). This should flash once every 344 seconds (5mins)

Installation

1. Choose a suitable location to install the alarm. (Do not install alarms in “Dead Zones”. near bathrooms, kitchens or air vents)
2. Mark out the screw locations using the base plate as a template.
3. Drill guide holes for the screws.
4. Insert the plastic lugs into the holes
5. Affix the base plate to the surface using the screws. Ensure the locking hooks are facing out.
6. Once the base plate is secured. take the alarm, and align the locking holes with the locking hooks.
7. To lock the device into place, turn clockwise gently.

Test the device

1. Press the Test/Hush button. The red LED indicator light will flash quickly. and the alarm will activate. This will show that the alarm is working. The alarm will enter the low sensitivity detection state (red LED flashes once every lOseconds but no alarm is sounding) for about 9 minutes before returning to its normal state.
2. Use a small amount of smoke to test if the alarm activates under smoke conditions. Once the alarm has activated you can press the hush button to silence the alarm. The alarm will enter the low sensitivity detection state (red LED flashes once. everylOseconds but no alarm is sounding) for about 9 minutes before returning to its normal state. The alarm will not activate again until the smoke concentration is higher.
3. If you press the Test/Hush button again you will cancel the low sensitivity detection state and the alarm will retttrn to normal mode.
   Note If. after cancelling low sensitivity detection state there is residual smoke in the chamber, the alarm will activate again.

Alarm memory

The ACGL-001PE smoke alarm has an alarm memory which activates after the alarm has been set off. Green LED will flash 3 times, every 13 seconds and repeats every 43 seconds. This is so the user can tell if the alarm has been activated from a distance without touching the alarm. The LED display will deactivate after 24 hours. If you press the test/hush button after the alarm is activated the alarm will go into its special alarm mode. After you release the test/mute button the alarm memory will be purged.

Maintenance

1. It is recommended by the manufacturer to test the alarm weekly. However. once a month is fine.
2. Keep the alarm clean by wiping down with a wet wipe. Keep the device free from dust and fly droppings. This should be done regularly
3. If the alarm is faulty or not working correctly. seek the advice of an installation specialist. (DO NOT dismantle the device)

Troubleshooting

ACGL-OO1PE Smoke Detecting Alarm User Manual

W ALLCLEAP.NZ| E CONTACTUS@PALLCLEAP.NZ| P 09 392 0000
---|---|---
Asbestos Surveys & Clearance
Water Quality Testing
Smoke Alarms| Soil Testing
Lead Based Paint
Mould & Moisture| Healthy Homes Compliance
Forensic Meth Consulting
Indoor Air Quality

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>