i-PRO WV-S2236L Network Camera Instruction Manual

• Recommended microphone (locally procured): Plug-in power type (Sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz))
• Input impedance:  Approx. 2 kΩ (unbalanced)
• Supply voltage: 2.5 V ±0.5 V
• Recommended cable length: Less than 1 m {3.28 feet}
• Input level for the line input: Approx. –10 dBV
• Recommended cable length: Less than 10 m {32.8 feet}

[4] Audio output connector
Connect an external speaker* using a stereo mini plug (ø3.5 mm). (Audio output is monaural.)

• Output impedance:    Approx. 600 Ω (unbalanced)

• Recommended cable length:  Less than 10 m {32.8 feet}

• Output level: –20 dBV

• Use a powered speaker.
  IMPORTANT:

  • Connect/disconnect the audio cables and turn on the power of the camera after turning off the power of the audio output devices. Otherwise, loud noise may be heard from the speaker.
  • Make sure that the stereo mini plug is connected to this cable. When a monaural mini plug is connected, audio may not be heard.
    When connecting a monaural speaker with amplifier, use a locally procured conversion cable (mono-stereo).

Note:

• The audio output can be switched to the monitor output. Refer to the “Operating Instructions” on our support website for descriptions of how to switch the output.

[5] EXT I/O terminals / EXT I/O terminal plug (accessory)
Note:

• Off, input, and output of the ALARM IN2 and 3 can be switched by configuring the setting.
  Refer to the Operating Instructions for further information about the ALARM IN2 and 3 settings (“Off”, “Alarm input”, “Alarm output” or “AUX output”).

• Alarm input1 / Black & white input / Auto time adjustment input, Alarm input2, Alarm input3
  Input specification:   No-voltage make contact input (4 V - 5 V DC, internally pulled up)
  OFF: Open or 4 V – 5 V DC
  ON:    Make contact with GND (required drive current: 1 mA or more)

• Alarm output, AUX output
  Output specification: Open collector output (maximum applied voltage: 20 V DC)
  OPEN: 4 V – 5 V DC by internal pull-up
  CLOSE: Output voltage 1 V DC or less (maximum drive current: 50 mA)

EXT I/O terminal plug      IMPORTANT:

• Install external devices so that they do not exceed the rating of the network camera.
• When using the ALARM IN2 and/or 3 as the output terminals, ensure they do not cause signal collision with external signals.

[6] MONITOR OUT terminal (factory shipment: NTSC monitor)
Used to connect a monitor used for adjustments during installation or when performing service.
IMPORTANT:

• The adjustment monitor is used for checking the adjustment of the angular field of view when installing the camera or when servicing. It is not provided for recording/monitoring use.
• Depending on the monitor, some characters (date, time, camera title, etc.) may not be displayed on the screen.
• When [16:9 mode] is selected for “Image capture mode”, the top and bottom of the image on the monitor will be displayed in black.

Note:

• The monitor out is set to NTSC in the default settings of the camera. If you want to change the monitor out setting to PAL, refer to the “Operating Instructions” on the our support website.

Indicators and buttons

The above illustration represents WV-S2136.

①INITIAL SET button (Initializing / NTSC ⇔ PAL switch button)
Follow the steps below to initialize the network camera.
⑴ Turn off the power of the camera.
When using a PoE hub, disconnect the Ethernet cable from the camera. When using an external power supply, disconnect the power cord plug (accessory) from the power supply terminal (12V DC).
⑵Turn on the power of the camera while pressing the INITIAL SET button, and make sure to release the button after approximately 15 seconds. In about 2 minutes later, the camera will start up and the settings including the network settings will be initialized. Retry if the camera does not start up normally.
IMPORTANT:

• When the camera is initialized, the settings including the network settings will be initialized. Before initializing the settings, it is recommended to write down the settings in advance.

• Do not turn off the power of the camera during the process of initialization. Otherwise, it may fail to initialize and may cause malfunction.

• When the INITIAL SET button is pressed (less than 1 second) to switch the output signal of the MONITOR OUT terminal, the MONITOR OUT terminal can be switched for the NTSC monitor ⇔ PAL monitor.
  ②LINK indicator

• When the camera is able to communicate with Lights orange the connected device
  ③ACT indicator

• When data is being sent via the network camera Blinks green (accessing)

④SD indicator

• When a microSD memory card is inserted and could be recognized
  Lights off → Blinks green → Lights off

• When data can be saved after the microSD memory card is inserted and the SD ON/OFF button is pressed (less than 1 second)
  Lights off → Lights green

• When data can be saved to the microSD memory card
  Lights green

• When the microSD memory card is removed after holding down the SD ON/OFF button (about 2 seconds)
  Lights green → Blinks green →
  Lights off (recording)
  Lights green → Lights off (waiting for recording)

• When data cannot be saved to the microSD memory card because an abnormality was detected or the microSD memory card is configured not to be used
  Lights off

Note:

• Lighting/blinking LED can be turned off with the software settings at any time. (The initial state is lighting or blinking.) Set the LED to be solid off if necessary, depending on the installation conditions. (☞ Operating instructions on our support website)

⑤SD memory card warning/error indicator

• When a warning status is detected
  Lights red
  *SD memory card warning detection conditions: After the total use time has exceeded 6 years and the number of overwrite times has exceeded 2000.
• When an error status is detected
  Blinks red
  *SD memory card error detection conditions: Write error, read error, etc.

Note:
• The default is off. According to the installation environment, set up with software as required. (☞ Operating instructions on our support website)
⑥SD ON/OFF button
⑴ When the SD ON/OFF button is pressed (less than 1 second), the SD indicator lights up in green and data can be saved to the microSD memory card.
⑵ When the SD ON/OFF button is held down (about 2 seconds), the SD indicator lights off and the microSD memory card can be removed.
⑦TELE button
Click the TELE button to adjust the zoom ratio to the “Tele” side.
⑧WIDE button
Click the WIDE button to adjust the zoom ratio to the “Wide” side.

Insert / remove a microSD memory card

Note:

• Use a microSD memory card dedicated to i-PRO cameras.
•  Refer to the Operating Instructions on our support website for further information about the microSD memory card settings.

■ Insert a microSD memory card

1. Remove the enclosure from the camera.
2. Insert the microSD memory card until it makes a clicking sound.
3. Take your fingers off the microSD memory card and check that its back end does not protrude over the side part of the camera.
4. After the microSD memory card has been inserted, press the SD ON/OFF button, and make sure the SD indicator is continually lit.

If you do not press the SD ON/OFF button after inserting the microSD memory card, the SD indicator is automatically lit approximately 5 minutes later. ■ Remove a microSD memory card
When removing a microSD memory card, reverse the procedure.

• To remove the microSD memory card, hold down the SD ON/OFF button for about 2 seconds. When the flashing SD indicator goes out, you can remove the microSD memory card.

IMPORTANT:

• Before turning off the camera power switch, make sure that the SD indicator is turned off.

If you turn off the camera power switch while the SD indicator is lit or flashing, the recorded data may be corrupted or damaged.
Note:

• When using a microSD memory card, format it using this product. Recorded data on the microSD memory card will be deleted when formatted. If an unformatted microSD memory card or a microSD memory card formatted with other devices is used, this product may not work properly or performance deterioration may be caused. Refer to the Operating Instructions on our support website for how to format a microSD memory card.
• When some microSD memory cards are used with this product, the product may not work properly or performance deterioration may be caused. Use a microSD memory card dedicated to i-PRO cameras.

Troubleshooting

Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below.

Symptom

| Cause/solution|

Reference pages

---|---|---
Power is not turned on.| When using a PoE device for power supply
•  Are the PoE device (IEEE802.3af compliant) and the RJ45 Network connector connected using an Ethernet cable? Check whether the connection is appropriately established.
•  Depending on the PoE device, the power supply will stop when the demanded power exceeds its total power limit for all PoE ports.
Refer to the operating instructions of the PoE device in use.| Installation Guide
When using DC power supply
•  Is the power cord plug (accessory) firmly inserted into the power supply terminal (12 V DC) of the camera?
Confirm the power plug is firmly connected.
•  Is the AC adaptor in use compliant with the Specifications? Check the Specifications regarding AC adaptor.
The LINK indicator does not light in orange even when the Ethernet cable is con- nected to the camera.| •  Is the Ethernet cable connected appropriately? Connect the Ethernet cable appropriately.
•  Is the hub or router connected to the camera operating appropriately?
Check if the hub or router in use is operating appropriately.
•  Is the Ethernet cable connected to the camera broken? Replace the cable with another one.| 11
The SD indicator does not light even when a microSD memory card is installed.| This indicator lights up green when the microSD memory card is recognized correctly and ready for use.
•  Has the inserted microSD memory card been formatted on a PC?
Use a microSD memory card formatted on the camera. Or install the software to format the microSD memory card on the PC.
Refer to our technical information website for further information about the supported software.
•  Is the inserted microSD memory card faulty? Replace the card with a normal one.| 12
The SD memory card warning/error indicator blinks red| •  The read / write error on the microSD memory card has occurred. Is the inserted microSD memory card faulty? Replace the card with a normal one.| 12
Audio input contains noise.| •  Check the following.
•  Grounding of the camera, a switching hub or periph- eral devices are not done.
•  The camera is used near an electrical power line.
•  The camera is used near a device which produces strong magnetic field or radio waves (such as near a TV/radio antenna, a motor of an air conditioning sys- tem, a transformer, etc.)
When audio input still contains noise even after checking the above possibilities, use a powered microphone or connect audio output with low output impedance.| Installation Guide
---|---|---
The focus can not be automatically adjusted.| •  In the following locations or with the following subjects, the focus may not be able to be automatically adjusted. In this case, manually adjust the focus from the setup menu.
•  When the subject moves a lot
•  When there are large changes to the lighting intensity
•  When the light level is low
•  When the subject or location is extremely bright or reflective
•  When viewing through windows
•  When the dome cover is in a locations where it can easily become dirty
•  Locations where there is not much contrast such as a white wall
•  When there is harsh flickering| Operating Instructions
After installing the enclosure, it may be out of focus.| Depending on the installation environment, the opti- mum focus position may change after the enclosure is installed. In that case, carry out the auto focus function from the setup menu.| Operating Instructions
When the enclosure is removed and the camera is checked on the screen, it appears that there are shadows in the four corners.| Depending on the position of the shading rubber on the lens, the shading rubber may appear in the viewing screen.
When the enclosure is attached to the camera, the shad- ing rubber returns to the correct position. This is not a fault with the camera.| –

Detail specifications

Basic

Power source 1:| DC 12 V
PoE (IEEE802.3af compliant)
---|---
Power consumption 1:| S2236L
S2136L| DC 12 V: 720 mA/ Approx. 8.6 W

PoE DC 48 V:180 mA/ Approx. 8.7 W (Class 0 device)

S2136| DC 12 V: 410 mA/ Approx. 4.9 W
PoE DC 48 V:    110 mA/ Approx. 5.3 W (Class 2 device)
Operating environment Ambient operating temperature:
Ambient operating humidity:| –10 °C to +50 °C {14 °F to 122 °F}
(Power on range: 0 °C to 50 °C {32 °F to 122 °F}) 10 % to 90 % (no condensation)
Storage environment
Storage temperature: Storage humidity:| –30 °C to +60 °C {–22 °F to +140 °F}
10 % to 95 % (no condensation)
Monitor output (for adjustment):| VBS: 1.0 V [p-p]/75 Ω, composite, Pin jack
An NTSC or PAL signal can be outputted from camera
(either press the INITIAL SET button quickly (within 1 second) or use software to select NTSC or PAL signal).
EXT I/O terminals:| ALARM IN1
(Alarm input 1/ Black & white input/ Auto time adjustment input) (×1) ALARM IN2 (Alarm input 2/ ALARM OUT) (×1)
ALARM IN3 (Alarm input 3/ AUX OUT) (×1)
Audio input:
For microphone input:
For line input:| ø3.5 mm stereo mini jack
Recommended applicable microphone: Plug-in power type
Sensitivity of microphone: -48 dB±3 dB (0 dB=1 V/Pa, 1 kHz))
Input impedance: Approx. 2 kΩ (unbalanced)
Supply voltage: 2.5 V ±0.5 V
Input level: Approx. –10 dBV
Audio output *2:| ø3.5 mm stereo mini jack (Audio output is monaural.)
Output impedance: Approx. 600 Ω (unbalanced)
Output level:          –20 dBV
Shock resistance:| S2236L| IK10 (IEC 62262)
Dimensions:| S2236L| ø129.5 mm × 102.5 mm (H)
{ø5-3/32 inches × 4-1/32 inches (H)} Dome radius 41.5 mm {1-5/8 inches}
S2136L
S2136| ø129.5 mm × 101 mm (H)
{ø5-3/32 inches × 3-31/32 inches (H)} Dome radius 40 mm {1-9/16 inches}
Mass:| S2236L| Approx. 570 g {1.26 lbs}
S2136L
S2136| Approx. 470 g {1.04 lbs}
Finish:
Others:| S2236L| Main body:

Dome cover:

| PC resin,     W
PC resin,      C| B G
---|---|---|---|---
S2136L
S2136
S2236L| Main body:
Dome cover:| ABS resin,  W
Acrylic resin, C| B G
3
Tamper-resistant enclosure *

1 Refer to our technical information website for further information about Power source and Power consumption information.
2 The audio output can be switched to the monitor output. Refer to the “Operating Instructions” on our support website for descriptions of how to switch the output.
*3 Component that has a structure on which the screws that are accessible after installation cannot be screwed or unscrewed using an ordinary screwdriver.
Camera

Color: C     0.007 lx {0.00065 footcandle}
(30IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11)
0.009 lx {0.00084 footcandle}
(50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11) 0.0006 lx {0.00006 footcandle}
(50IRE, F1.3, Maximum shutter: max. 16/30 s, AGC: 11)
G     0.018 lx {0.0019 footcandle}
(30IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11)
0.025 lx {0.0024 footcandle}
(50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11) 0.0016 lx {0.00015 footcandle}
(50IRE, F1.3, Maximum shutter: max. 16/30 s, AGC: 11)
BW: 0 lx {0 footcandle}
(50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11, when the IR LED is lit)
C  0.006 lx {0.00056 footcandle}
(50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11) 0.0004 lx {0.00004 footcandle}
(50IRE, F1.3, Maximum shutter: max. 16/30 s, AGC: 11)
G     0.017 lx {0.0016 footcandle}
(50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11)
0.0011 lx {0.0001 footcandle}
(50IRE, F1.3, Maximum shutter: max. 16/30 s, AGC: 11)
S2136
Color:
C     0.007 lx {0.00065 footcandle}
(30IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11)
0.009 lx {0.00084 footcandle}
(50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11) 0.0006 lx {0.00006 footcandle}
(50IRE, F1.3, Maximum shutter: max. 16/30 s, AGC: 11)
G   0.018 lx {0.0019 footcandle}
(30IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11)
0.025 lx {0.0024 footcandle}
(50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11) 0.0016 lx {0.00015 footcandle}
(50IRE, F1.3, Maximum shutter: max. 16/30 s, AGC: 11)
BW:
C     0.006 lx {0.00056 footcandle}
(50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11) 0.0004 lx {0.00004 footcandle}
(50IRE, F1.3, Maximum shutter: max. 16/30 s, AGC: 11)
G     0.017 lx {0.0016 footcandle}
(50IRE, F1.3, Maximum shutter: Off (1/30 s), AGC: 11)
0.0011 lx {0.0001 footcandle}
(50IRE, F1.3, Maximum shutter: max. 16/30 s, AGC: 11)

• Converted value
  Intelligent Auto:| On/ Off
  ---|---
  Super Dynamic 1:| On/ Off
  The level can be set in the range of 0 to 31.
  Dynamic range:| Max. 144 dB (Super Dynamic: On, Level: 31)
  Maximum gain:| The level can be set in the range of 0 to 11.
  Adaptive black stretch:| The level can be set in the range of 0 to 255.
  Back light compensation (BLC) / High light compensation (HLC):| BLC/ HLC/ Off
  The level can be set in the range of 0 to 31. (only when Super Dynamic/ Intelligent Auto: Off)
  Fog compensation:| On/ Off
  The level can be set in the range of 0 to 8. (only when Intelligent Auto / Auto contrast adjust: Off)
  Light control mode setting:| Outdoor scene/ Indoor scene (50 Hz)/ Indoor scene (60 Hz)/ Fix shutter
  Shutter speed:| [60 fps mode] 1/60 Fix, 1/100 Fix, 1/120 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix, 1/4000 Fix, 1/10000 Fix[30 fps/15 fps mode] 1/30 Fix, 3/120 Fix, 2/100 Fix, 2/120 Fix, 1/100 Fix, 1/120 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix, 1/4000 Fix, 1/10000 Fix [50 fps mode] 1/50 Fix, 1/100 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix,  1/4000 Fix, 1/10000 Fix [25 fps/12.5 fps mode] 1/25 Fix, 3/100 Fix, 2/100 Fix, 1/100 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix, 1/4000 Fix, 1/10000 Fix
  Maximum shutter:| [60 fps mode] Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s,Max. 1/250 s, Max. 1/120 s, Max. 1/100 s, Max. 2/120 s, Max. 1/30 s, Max. 2/30 s, Max. 4/30 s, Max. 6/30 s, Max. 10/30 s, Max. 16/30 s [30 fps/15 fps mode] Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s, Max. 1/250 s, Max. 1/120 s, Max. 1/100 s, Max. 2/120 s, Max. 2/100 s, Max. 3/120 s, Max. 1/30 s, Max. 2/30 s, Max. 4/30 s, Max. 6/30 s, Max. 10/30 s, Max. 16/30 s
  [50 fps mode] Max.1/4000 s, Max.1/2000 s, Max.1/1000 s, Max.1/500 s, Max.1/250 s, Max.1/100 s, Max.2/100 s, Max.1/25 s, Max.2/25 s, Max.4/25 s, Max.6/25 s, Max.10/25 s, Max.16/25 s [25 fps/12.5 fps mode] Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s, Max. 1/250 s, Max. 1/100 s, Max. 2/100 s, Max. 3/100 s, Max. 1/25 s, Max. 2/25 s, Max.  4/25 s, Max. 6/25 s, Max. 10/25 s, Max. 16/25 s
  IR LED Light:S2236L S2136L
  IR LED Light   S2236L S2136L| High/ Middle/ Low/ Off
  C Maximum irradiation distance: 70 m {Approx. 230 ft} (30IRE)
  50 m {Approx. 164 ft} (50IRE)
  G Maximum irradiation distance: 50 m {Approx. 164 ft} (30IRE)*
  35 m {Approx. 116 ft} (50IRE)
• Converted value
  High/ Middle/ Low/ Off
  C Maximum irradiation distance: 70 m {Approx. 230 ft} (30IRE)
  50 m {Approx. 164 ft} (50IRE)
  G Maximum irradiation distance: 50 m {Approx. 164 ft} (30IRE)
  35 m {Approx. 116 ft} (50IRE)
• Converted value
  ---|---
  White balance:| ATW1/ ATW2/ AWC
  Digital noise reduction:| The level can be set in the range of 0 to 255.
  Privacy zone:| On/ Off
  Up to 8 zones available
  VIQS:| On/ Off
  up to 8 zones available
  Camera title on screen:| On/ Off
  Up to 40 characters, Up to 2 lines (alphanumeric characters, marks)
  Video Motion Detection (VMD):| On/ Off
  4 areas available
  Scene Change Detection (SCD):| On/ Off
  1 area available
  Audio Detection:| On/ Off
  AI Sound classification:| Selectable from Gunshot, Yell, Vehicle horn, Glass break
  Image rotation 2, 3, *4:| 0° (Off)/ 90°/ 180° (Upside-down)/ 270°

Lens

Zoom ratio:
Optical zoom Extra optical zoom| ** 3.1× (Motorized zoom / Motorized focus) Max 9.3×
(3.1× – 9.3× when resolution is 640×360)
---|---
Focal length:| 2.9 mm – 9 mm {1/8 inches – 11/32 inches}
Maximum aperture ratio:| 1:1.3 (WIDE) – 1:2.5 (TELE)
Focus range:| 0.3 m {11-13/16 inches} – ∞
Aperture range:| F1.3 – Close
Angular field of view:| S2236L
[16:9 mode] Horizontal: 36° (TELE) – 114° (WIDE)
Vertical:    20° (TELE) – 60° (WIDE)
[4:3 mode] Horizontal: 27° (TELE) – 82° (WIDE)
Vertical: 20° (TELE) – 60° (WIDE)
S2136L  S2136
* [16:9 mode] Horizontal: 36° (TELE) – 115° (WIDE)
Vertical:    20° (TELE) – 61° (WIDE)
[4:3 mode] Horizontal: 28° (TELE) – 82° (WIDE)
Vertical:    20° (TELE) – 61° (WIDE)
DORI 1:
Detect (25 ppm / 8 ppf)
Observe (62.5 ppm / 19 ppf)
Recognize (125 ppm / 38 ppf)
Identify (250 ppm / 76 ppf)
Detect (25 ppm / 8 ppf)
Observe (62.5 ppm / 19 ppf)
Recognize (125 ppm / 38 ppf)
Identify (250 ppm / 76 ppf)| S2236L

118.2 m {387.7 ft} (TELE)   24.9 m {81.8 ft} (WIDE)
47.3 m {155.1 ft} (TELE)   10.0 m {32.7 ft} (WIDE)
23.6 m { 77.5 ft} (TELE)      5.0 m {16.4 ft} (WIDE)
11.8 m { 38.8 ft} (TELE)      2.5 m { 8.2 ft} (WIDE)

S2136L      S2136
118.2 m {387.7 ft} (TELE) 24.5 m {80.3 ft} (WIDE)
47.3 m {155.1 ft} (TELE)  9.8 m {32.1 ft} (WIDE)
23.6 m { 77.5 ft} (TELE) 4.9 m {16.1 ft} (WIDE)
11.8 m { 38.8 ft} (TELE)  2.4 m { 8.0 ft} (WIDE)

Adjusting angle:| Horizontal (PAN) angle: -240° to +120°
Vertical (TILT) angle: -30° to +85°
Azimuth (YAW) angle: ±100°

1 Maximum distance at which a camera’s tele and wide lens can meet DORI specifications. This value does not indicate the performance of the camera. Calculations made with the camera installed horizontally at resolution of maximum resolution.
Network

Network:

|

10BASE-T/100BASE-TX, RJ45 connector

---|---
Resolution : H.265/ H.264 1 JPEG (MJPEG)| [16:9 mode (60 fps mode)] [16:9 mode (30 fps mode)] [16:9 mode (50 fps mode)] [16:9 mode (25 fps mode)] 1920×1080/ 1280×720/ 640×360/ 320×180
[4:3 mode (30 fps mode)] [4:3 mode (25 fps mode)] 1280×960/ VGA/ QVGA
[4:3 mode (15 fps mode)] [4:3 mode (12.5 fps mode)] 2048×1536 2/ 1280×960/ VGA/ QVGA
Image compression method 3:
H.265/ H.264 1| ****

Transmission priority: Constant bit rate/ VBR/ Frame rate/ Best effort
Frame rate:
[60 fps mode] 1 fps/ 3 fps/ 5 fps/ 7.5 fps/ 10 fps/ 12 fps/ 15 fps/ 20 fps/ 30 fps/60 fps
[30 fps mode] 1 fps/ 3 fps/ 5 fps/ 7.5 fps/ 10 fps/ 12 fps/ 15 fps/ 20 fps/ 30 fps
[15 fps mode] 1 fps/ 3 fps/ 5 fps/ 7.5 fps/ 10 fps/ 12 fps/ 15 fps
[50 fps mode] 1 fps/ 3.1 fps/ 4.2 fps/ 6.25 fps/ 8.3 fps/ 12.5 fps/ 20 fps/ 25 fps/50 fps
[25 fps mode] 1 fps/ 3.1 fps/ 4.2 fps/ 6.25 fps/ 8.3 fps/ 12.5 fps/ 20 fps/ 25 fps
[12.5 fps mode] 1 fps/ 3.1 fps/ 4.2 fps/ 6.25 fps/ 8.3 fps/ 12.5 fps
(The frame rate is limited to “bit rate”. When a value with an asterisk
() is selected, the actual frame rate may be lower that the value selected.)
Bit rate per client:
64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/ 768 kbps/ 1024 kbps/ 1536 kbps/ 2048 kbps/ 3072 kbps/ 4096 kbps/ 6144 kbps/ 8192 kbps/ 10240 kbps/ 12288 kbps/ 14336 kbps/ 16384 kbps/ 20480 kbps/ 24576 kbps/
–FREE ENTRY–
*The available range of the bit rate varies depending on the setting selected for “image capture size”.
Image quality:
•  For “Constant bit rate”, “Frame rate”, and “Best effort”: Low(Motion priority)/ Normal/ Fine(Image quality priority)
•  “VBR”:
0 Super fine/ 1 Fine/ 2/ 3/ 4/ 5 Normal/ 6/ 7/ 8/ 9 Low
Transmission type:
Unicast port (AUTO)/ Unicast port (MANUAL)/ Multicast

JPEG (MJPEG)| Image quality:
0  SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/ 6/ 7/ 8/ 9 LOW
(10 steps: 0-9)
Transmission type: Pull (Refresh interval)/ Push (MJPEG)
Refresh interval:
[60 fps mode] 0.1  fps/ 0.2 fps/ 0.33 fps/ 0.5 fps/ 1 fps/ 2 fps/ 3 fps/ 5 fps/ 6 fps/ 10 fps/ 12 fps/ 15 fps/ 30 fps/ 60 fps
[30 fps mode] 0.1 fps/ 0.2 fps/ 0.33 fps/ 0.5 fps/ 1 fps/ 2 fps/ 3 fps/ 5 fps/ 6 fps/ 10 fps/ 12 fps/ 15 fps/ 30 fps
[15 fps mode] 0.1 fps/ 0.2 fps/ 0.33 fps/ 0.5 fps/ 1 fps/ 2 fps/ 3 fps/ 5 fps/ 6 fps/ 10 fps/ 12 fps/ 15 fps
[50 fps mode] 0.08 fps/ 0.17 fps/ 0.28 fps/ 0.42 fps/ 1 fps/ 2.1 fps/ 3.1 fps/ 4.2 fps/5 fps/ 8.3 fps/ 12.5 fps/ 25 fps/ 50 fps
[25 fps mode] 0.08 fps/ 0.17 fps/ 0.28 fps/ 0.42 fps/ 1 fps/ 2.1 fps/ 3.1 fps/ 4.2 fps/5 fps/ 8.3 fps/ 12.5 fps/ 25 fps
[12.5 fps mode] 0.08 fps/ 0.17 fps/ 0.28 fps/ 0.42 fps/ 1 fps/ 2.1 fps/ 3.1 fps/ 4.2 fps/5 fps/ 8.3 fps/ 12.5 fps(JPEG frame rates are limited when using JPEG and
H.265/H.264 simultaneously.)
---|---
Smart coding:| GOP(Group of pictures) control
Off/ Low (Variable GOP 1s-8s)/ Mid (Variable GOP 4s-16s)/ Advanced (Fixed GOP 60 seconds with 1 second Key frame)/ Frame rate control (Variable GOP 4s-16s with frame rate control)
Advanced and Frame rate control are only available with H.265.
Smart VIQS
On(High)/On(Low)/Off
Smart P-picture control
On/Off
Audio compression method:| G.726 (ADPCM): 16 kbps/ 32 kbps
G.711:  64 kbps
AAC-LC 4:  64 kbps/ 96 kbps/ 128 kbps
Bandwidth control:| Unlimited/ 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/768 kbps/ 1024 kbps/ 2048 kbps/ 4096 kbps/ 6144 kbps/8192 kbps/ 10240 kbps/ 15360 kbps/ 20480 kbps/ 25600 kbps/30720 kbps/ 35840 kbps/ 40960 kbps/ 51200 kbps
Protocol:| IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, SSL/TLS, SMTP, DNS, NTP, SNMPv1/v2/v3, DHCPv6, RTP, MLD, ICMP, ARP, IEEE 802.1X, DiffServ, LLDP, FTP, SFTP, MQTT IPv4: TCP/IP, UDP/IP, HTTP, HTTPS, SSL/TLS, RTSP, RTP, RTP/RTCP, SMTP, DHCP, DNS, DDNS, NTP, SNMPv1/v2/v3, UPnP, IGMP, ICMP, ARP, IEEE 802.1X, DiffServ, SRTP, LLDP, FTP, SFTP, MQTT
Security:| User authentication, Host authentication, HTTPS
FIPS 140-2 level3 5
OS:| Microsoft Windows 11
Microsoft Windows 10
---|---
Browser 6:| Microsoft Edge Firefox
Google Chrome
Maximum concurrent access number:| 14* (Number of sessions that can connect to cameras at the same time)

• Depends on network conditions
  Multi-screen:| Up to 16 camera images can be displayed simultaneously on a multi-screen. 7
  (Including the camera itself)
  microSD memory card 8, 9, 10, 11, 12:| microSDXC memory card: 64 GB, 128 GB, 256 GB, 512 GB
  microSDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB
  microSD memory card: 2 GB
  Mobile terminal/
  Tablet terminal compatibility:| iPad / iPhone (iOS 8.0 or later), AndroidTM terminals

  1. H.265/H.264 can be selected for each stream.

  2. Used by super resolution techniques.

  3. Transmission for 4 streams can be individually set.

  4. When recording audio on a microSD memory card, only use AAC-LC (Advanced Audio Coding – Low Complexity).

  5. For the following model only: WV-S2236LA, WV-S2236LA-B, WV-S2236LGA, WV-S2236LGA-B, WV-S2136LA, WV-S2136LA-B, WV-S2136LGA, WV-S2136LGA-B, WV-S2136A, WV-S2136A-B, WV-S2136GA, WV-S2136GA-B

  6. For information on the operation verification of the supported web browsers, refer to our technical information website .

  7. When using MJPEG/JPEG (Refresh interval) only.

  8. Use a microSD memory card dedicated to i-PRO cameras.

  9. For possible number of images and duration (an indication) that can be saved on the microSD memory card, refer to our technical information website below.
     Possible number of JPEG images that can be saved:
     Possible duration of stream images (H.265 or H.264) that can be saved:

  10. Use the microSD memory card with SD Speed Class 6 or higher. Use the microSD memory card that complies with UHS-1(Ultra High Speed-1) in the case of SD Speed Class 10.

  11. Refer to our technical information website for the replacement cycle (target) of a microSD memory card.

  12. When repeatedly recording images on a microSD memory card using the auto overwrite function, make sure to use a microSD memory card with high reliability and durability.

Tokyo, Japan
https://www.i-pro.com/
Authorised Representative in EU:
i-PRO EMEA B.V.
Laarderhoogtweg 25, 1101 EB
Amsterdam, Netherlands
**** i-PRO EMEA B.V. UK Branch
1010 Cambourne Business Park,
Cambridgeshire CB23 6DP
© i-PRO Co., Ltd. 2022
N1221-2053 PGQP3343XA

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>