DP KVM21 KVM Switch USB HDMI 2 1 Spacetronik User Manual

DP KVM switch 2 in 1 out

Special Note

Before using this product, please read this instruction manual carefully.
Please keep this book in a safe place so that you can refer to it at any time in the future.
Please use it correctly after fully understanding the content.
The company reserves the right to make changes to the product. Due to technical updates, product parameters are subject to change without notice.

Overview

This DP KVM two-in-one-out switch supports the simultaneous use of both HDMI and DP interfaces, which can realize the display and operation of two main computer main screens and sub screens on one monitor, and the resolution can support up to 3840x2160P@60P.

Features

• Support multi-system use such as Windows, Mac, Linux, Android, etc.,
• Support the use of USB2.0 and USB1.1 devices,
• Support DisplayPort1.2 protocol parameter standard,
• Support input and output resolution up to 3840*2160@60Hz YUV4:4:4,
• Support USB port plug-in automatic identification detection, automatic scanning, computer sleep wake-up and other functions,

Connection diagram

Switching method

• The first switching method: key switch
  Press the button on the panel to switch to the corresponding host.

• The second switching method: remote control switching
  Point the remote control directly at the KVM switch panel to switch to the corresponding computer host

• The third switching method: Mouse switch
  KVM mouse switching method: double-click the middle wheel of the mouse + right button to switch to the right, Double-click the middle wheel of the mouse + the left button to switch to the left. The switch is completed within 2.5 seconds of operation, as  shown in the figure below:
  

• The fourth switching method: keyboard hotkey switching
  Attached table: keyboard hotkey function tableSupport 5 hotkey combinations: R’Ctrl/L’Ctrl/Scroll lock/Num lock/Caps lock.
  The default is: R’Ctrl hotkey modeNote: If the R’Ctrl hotkey mode is changed to any of the 5 hotkey modes, the R’Ctrl key needs to be changed to the current hotkey  combination mode during operation

  Double click R’Ctrl+1~4+Enter| Switch to input channel 1~4
  Double click R’Ctrl+B+Enter| Buzzer on and off
  Double click R’Ctrl+T+Enter| Channel input power-on recognition function on and off
  Double click R’Ctrl+M+Enter| Mouse switch function on and off
  Double click R’Ctrl+R+Enter| Reset function is on
  Double click R’Ctrl+S+Enter| Input channel cycle switching function on and off
  Double click R’Ctrl+S+2-999+Enter| Input channel cycle switching function time setting

• The fifth switching method: RS232 serial communication switching
  Attached table: RS232 communication code, baud rate:

Serial port settings| 115200bps, 8 bits of data, 1 stop bit,
check code: None, hexadecimal,
---|---
Enter 1| 0x30 0x30 0x30 0x0a 0x0d
Enter 2| 0x30 0x30 0x31 0x0a 0x0d

Performance parameter

Input and output
support resolution| 3840x2160P@60Hz/30Hz, 2560x1440P@144Hz/120Hz/ 60Hz, 1920x1080P@60Hz/1280x720P@60Hz, etc.,
---|---
DP protocol version| DisplayPort1.2 protocol
DP maximum transmission rate| 21.6Gbit/s
USB protocol| USB2.0, 1.1, 1.0
Maximum working voltage and current| 5V/800mA
Range of working temperature| -10 to +60°C
Range of working temperature| 5 to 90%RH (non-condensing)
Power adapter specifications| AC 100V-240V 50-60Hz input, DC5V/1A output
Product material| Iron shell
Product Size| 200x65x28(mm)
Product weight| 450g

Parts List

Safety instructions

In order to ensure the reliable use of equipment and the safety of personnel, please install, use and maintain Please observe the following:

• Do not use this product in the following places: dust, oily smoke, conductive dust, corrosive Places with gas, flammable gas; Places exposed to high temperature, condensation, wind and rain; Vibration, Impact occasions.
  Electric shock, fire, and misoperation can also cause product damage and deterioration;

• Avoid wiring, plugging and unplugging the cable plug in a live state, otherwise it is easy to cause electric shock. Or cause circuit damage;

• Installation and wiring must be firm and reliable, poor contact may cause misoperation;

• This product is grounded through the grounding wire of the power cord.
  To avoid electric shock, the grounding wire must be Connect to the ground.
  Before connecting the input or output of this product, be sure to connect the The product is properly grounded;

• The external power supply must be cut off before installation, wiring and other operations can be carried out, otherwise Can cause electric shock or equipment damage;

• In the following cases, please disconnect the power immediately and contact the company:
  1. Water in the equipment;
  2. The equipment is broken or the casing is broken;
  3. The equipment works abnormally or the displayed performance has been completely changed;
  4. The equipment produces odor, smoke or noise.

• Please do not repair the equipment by yourself, except for clear instructions in the manual.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>