Ansoko

Ansoko UHF 16-Channel Pack Long Range Rechargeable

Introduction

Each walkie-talkie has 16 channels preprogrammed and is ready to use right out of the box. Channels may also be programmed using a programming cord (sold separately). 2 Watt output power, UHF frequency band. As long as they are all on the same channel and within the range of the Ansoko two-way radios—which varies depending on the terrain from 0.6 to 3.5 miles—any number of them can be utilized together. Each radio has its own dedicated charging base, eliminating the need to share a base with other two-way radios, and the 1500mAh rechargeable battery provides 8 to 12 hours of talk time under ordinary use.

A built-in LED torch for use in emergencies or while travelling, 105 DCS privacy codes, 50 CTCSS privacy codes to increase frequency use (available with programming cable), and an emergency alarm feature. Free customer service, a 30-day return period, and a one-year warranty on walkie-talkies and accessories. The FCC has authorized the gadget and it fully complies with FCC regulations; FCC ID: ZP5BF-888S.

• LED INDICATOR Lights red during transmit, green when receiving a signal
• CHANNEL SWITCH Rotate to select a channel. No. 16 is the scanning channel
• POWER SWITCH / VOLUME CONTROL Turn clockwise to switch ON the transceiver. Turn counterclockwise to switch OFF transceiver. Rotate to adjust volume.
• PTT (PRESS-TO-TALK) BUTTON Press button to transmit. Release to receive.
• MONI (MONITOR)  BUTTON Press and Hold (Squelch OFF) to hear background noise; Release to return to normal operation.
• FUNC (FUNCTION BUTTON)  BUTTON Press to activate LED torch function.
• SPEAKER MICROPHONE / PROGRAMMING CABLE JACK

OPERATION

• SWITCHING POWER ON/OFF Turn the Power switch/Volume control (A) clockwise. You will hear a beep and speech indicating the transceiver is ON.
• ADJUSTING THE VOLUME Hold Monitor button (E) own to listen to audio level while rotating the Power switch/Volume control      (A). Rotate Volume Control to increase / decrease the volume.
• SELECTING THE CHANNEL Turn the Channel Switch (B) to the desired channel. No. 16 is the Scanning Channel.

TRANSMITTING

To transmit, Press and Hold PTT (D) and speak into the microphone in a normal tone of voice. The LED indicator lights continuously red when transmitting. For maximum sound clarity at the receiving station, hold the transceiver 2 to 3 inched from mouth and talk in a normal tone of voice.

NOTE: Yelling does not make your signal louder.

CHARGING the LI-ION BATTERY PACK

Charge the battery pack before using it. The new or stored (more than 2 months) battery pack cannot reach full capacity after the first charge. After 2 or 3 charges and discharges, it will reach full charge.

1. Plug adapter into electrical socket.
2. Insert transceiver or battery into the charging tray.
3. Ensure that the battery contacts connect with the drop-in charging tray. While charging is taking place, the LED will glow Red.
4. After 3 hours charging, the LED indicator will light Green.
5. Remove battery or transceiver from the charging tray.

Asterisk [ * ] designates function changed via software

• SQUELCH LEVEL The purpose of the Squelch is to mute the speaker when no signals are present. With the squelch correctly set, you will only hear sound when a signal is present.
• TIME-OUT TIMER (TOT) The TOT limits the length of a user’s transmission. The purpose of the TOT is to prevent transmitting for a long period of time, causing thermal damage to the radio. And alert will sound when the limit for that transmission has been reached.
• SCANNING Scanning is used for hands off monitoring of your favorite frequencies. When the transceiver options are set to SCAN (via software), setting the channel selector to channel 16 directs the radio to scan the selected channels from 1 -15.
  • Transceiver stops scanning when a signal is detected and continues when signal is gone.
  • If there are less than 2 channels, it cannot scan. (Go figure)
  • On channel 16, Press and Hold the PTT and MONI buttons while switching ON the transceiver to turn the Scanning ON or OFF.
  • If FM radio function is activated, Radio cannot scan.
• VOICE PROMPT
  • VP can be set ON/OFF via software.
  • On channel 10, Press and Hold the PTT and MONI buttons while switching ON the transceiver to also Activate or Deactivate Voice Prompt.
  • On channel 15, Press and Hold the PTT and MONI buttons while switching ON the transceiver to change Voice Prompt Language (CHI / ENG)
  • Any channel 1-16, Press and Hold MONI only while switching ON the transceiver will Deactivate Voice Prompt for that session only.
• VOX (Voice Operated Transmit) VOX eliminates the need for using the PTT key to transmit. The transmitter is keyed when the VOX circuit senses you are speaking into the microphone.
  • When operating the VOX function, set the VOX Gain level to recognize the desired sound level.
  • If level is too sensitive, transceiver will key with noise in the background.
  • If level is not sensitive enough, it will not pick up your voice. Set level for smooth transmission.
  • On channel 1-5, Press and Hold the PTT and MONI buttons while switching ON the transceiver to turn the VOX ON or OFF.
• EMERGENCY ALARM On channel 11, Press and Hold the PTT and MONI buttons while switching ON the transceiver to turn the Alarm Function ON or OFF.  This is a function for your receiver only. You will Not transmit the alarm.

BATTERY SAVER

Reduces the battery power used when not receiving a signal. Battery saver turns on automatically 10 seconds after no signal is received and no operation is being performed.

BATTERY LOW ALERT

Reminds you that battery needs recharging. Alert tone will sound and Red LED will blink.

MONITOR

When no signal is being received, Press and Hold the MONI. This is helpful for adjusting volume level and receiving weak signals.

• BUSY CHANNEL LOCK-OUT (BCL) BCL prevents you from transmitting on a channel if a signal is present. Pressing the PTT switch while a channel is in use will emit an alert tone and inhibit the transmitter.
• BEEP TONE If turned on, radio will give short tone to indicate that there is nothing programmed for that channel.
• CTCSS / DCS CTCSS (Continuous Tone Coded Squelch System) or (Digital Coded Squelch).     CTCSS / DCS Description You may sometimes want to hear calls only from specific persons or groups. This option allows you to ignore unwanted calls from others on the same frequency. These tones are sub-audible (cannot be heard) and are selectable via software.

NOTE: These tones do NOT cause your conversation to be private or scrambled. It only relieves you from listening to unwanted conversations.

SUMMARY of FUNCTION ACTIVATION

• Ch. 1-5, Press / Hold both PTT and MONI, and Power ON
• VOX – ON / OFF.
• Ch. 10, Press / Hold both PTT and MONI, and Power ON
• Voice Prompt – ON / OFF
  • Ch. 11, Press / Hold both PTT and MONI, and Power ON
• Alarm Function ON / OFF (if selected via SW)
  • Ch. 15, Press / Hold both PTT and MONI, and Power ON
• Change Language (CHI / ENG)
  • Ch. 16, Press / Hold both PTT and MONI, and Power ON
• Scan ON / OFF  (if option set via software)
  • Ch. 1-16, Press / Hold MONI only and Power ON Deactivates Voice Prompt for that session only.

SPECIFICATIONS

Frequency Range| 400 – 470MHz
RF Rated Power| < = 5W
Channel Capacity| 16
Operating Voltage| 3.7V
Dimensions| 115mm x 60mm x 33mm 4.53″ x 2.36″ x 1.30″
Weight| 150g (5.3oz)

TROUBLESHOOTING GUIDE

No Power| Check Battery Installation and/or replace/charge battery.
Can’t| Verify that the frequency and CTCSS tones are the same
communicate| for all members. If all checks out okay, make sure you are
with other| all within range.
members|
Hearing other

stations

| Change your CTCSS for that channel. Change to another

channel.

I can clearly hear| Check if microphone is blocked. If so, return radio to
members of my| dealer for maintenance. Sometimes your frequency is the
group, but my| same as the frequency of other groups.
voice is|
intermittent.|
Can’t turn on the| Check the battery contacts on the radio. If they are broken
radio, or it turns| or twisted, return your radio to an authorized dealer for
on and quickly| maintenance.
shuts down.|

Frequently Asked Questions

Does the ear peace have a mic to it? Or is it only for listening and when we need to talk we need to talk directly to the unit?

Yes, there is a mic on the earpiece as well as a PTT button, you don’t have to talk to the unit or press the PTT button on the unit when you use the earpieces.

Can these be set up to scan the channels?

Yes ,they can.

does ansoko make a gang charger for the a-8s ?

They worked great. We used it at the church.

Am I reading this correctly that the 10 pack is $119.70 or is that per unit?

the price is for 10 Pack.

Can i use this radio with the Tekk x700?

No you cannot.

How far will this reach out in miles

Idk about miles. We used it for escape rooms, 2000sq ft.

Can the chargers be plugged into 220v for when I’m abroad?

Yes, the input voltage range is 110~230 V.

Anyone have the link to order Spare headsets?

you could order from this link: https://www.amazon.com/dp/B078Z79WV2.

Do these radios have an AC adapter

Charging units come with each one.

Can the chargers be plugged into 220v for when I’m abroad?

Yes. The chargers are rated for 110-240v.

Maybe i missed it, but what is the model of this radio? is it the ansoko a-8s?

I’m sorry but I didn’t see a model number. Have you tried reaching out to Customer Service or actually calling the company who makes these walkie talkies. I will tell you this though, they work really well and I highly recommend. They came through for our backpack drive servicing over 250 kids. The clarity is amazing. If I can find the actual boxes that they came in, I will let you know if it says what models they are.

Can I add more walkie talkies as time goes by?

Sure, they can work together as long as they are on the same channel. So anytime you want to add more radios, it won’t be an issue.

Can I buy the protection plan separately?

I am afraid not, as the protection plan is provided by a third-party insurance company.

Was wondering if they are all on the same channel can all hear the conversation?

Yes, you are able to communicate between all 10 units. Sometimes you can also communicate with others on the same channel that are not part of your 10.

How water resistant are these units?

They are just splash-proof, not water-resistant designed.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>