iNVERBOT X60 AI-Wireless Robotic Pool Cleaner User Manual

iNVERBOT X60 AI-Wireless Robotic Pool Cleaner

Product Information

The product is a robotic pool cleaner designed to efficiently clean the pool floor, walls, and waterline. It comes with multiple cleaning modes, a large filter capacity, and various technical specifications to ensure optimal performance. The package includes the robot, charger, hook, magnetic cap (x2), user manual, and plugcover.

Technical Specifications

• Model: X80, X60, X45, X30
• Endurance Time (Floor Mode): 8h, 6h, 4.5h, 3h
• Endurance Time (Floor/Wall/Waterline Mode): 4.5h, 3.5h, 2.5h, 2h
• Charging Time: 5h, 4h, 3h, 2h
• Battery: 14Ah (352wh), 10.4Ah (262wh), 7.8Ah (196wh), 5.2Ah (131wh)
• Optimum Pool Temperature: 4°C to 35°C
• Cleaning Mode: Floor only / Floor, Wall & Waterline
• Multiple Cycle Option: 0.5h / 1h / 2h Full Run
• AI Timer: Clean every 24h / 48h / 72h
• App Application: Yes
• Filter Capacity: 3.2L
• Filtration Accuracy: 180m
• Pump Flow Rate: Running power 30-110W
• Moving Speed: 12m/min
• Number of Motors: 3
• Charger Input: 90-265VAC ~ 50/60Hz
• Running Voltage/Current: 25.2V/1.2A
• Charger Power: 72.5W
• Robot NW/GW: 12kg / 17kg, 11.5kg / 16.5kg
• Robot Dimension (LWH): 495395265 mm
• Robot Packaging Dimension (LWH): 580448330 mm

Product Usage Instructions

1. To achieve the most efficient cleaning, place the robot at the corner of the pool for quick coverage of the entire pool floor area.
2. To drain water from the robot, place it on the edge of the pool and let the water drain out.
3. To open the filter box, follow the instructions provided in the user manual.
4. For battery protection, ensure that the robot is fully charged every 3 months and insert the magnetic cap back into the robot if it is not used for more than 14 days.
5. Do not charge the robot outdoors and avoid long-term exposure to the sun.
6. Ensure the robot is fully dry before storage to prevent degradation or damage to the motors or internal structure.
7. Clean the filter basket thoroughly after usage and do not leave dirt or debris to dry in the filter basket.
8. Store the charger cable neatly without twists during long-term storage.
9. Optimum storage temperature should be between -10°C and 45°C, with a storage humidity between 30% and 70% RH.
10. Before using or charging the robot, remove the magnetic cap from the bottom. Insert the magnetic cap to the machine’s bottom for battery protection when not using the robot for more than 14 days.
11. If the robot fails, insert the magnetic cap into the robot for 2 seconds, remove it, and restart the robot to reset it.
12. Connect the robot to a power supply (90-265V) using the provided charger. The red light indicates charging, and the green light indicates a fully charged robot. It is recommended to fully charge the robot before its first use.

TIPS

• How to achieve the most efficient cleaning
  Place the robot at the corner of the pool for quick coverage of the entire pool floor area.

• How to drain water from the robot
  Place the robot on the edge of the pool for a while and let the water drain out.

• How to open the filter box

• CAUTION
  For battery protection, the robot should be fully charged every 3 months and the magnetic cap should be inserted back into the robot if it is not used for more than 14 days.
  Do not charge the robot outdoors.

• Do not long-term expose the robot to the sun.

WARNINGS
This page contains information that will help you operate the robot safely, prevent hazards and prevent damage to the robot or other property.

GENERAL WARNINGS

• Read the instructions before operating the robot.
• The robot is designed for pool cleaning; do not use it for other purposes.
• Keep the robot out of reach of children or persons with reduced physical, sensory or mental capabilities without supervision or instruction.
• The robot must be installed, operated and maintained as specified in this manual.
• The robot is to be installed in accordance with manufacturer’s guidelines and in compliance with the relevant requirements of the local or national standards for installation. The manufacturer is not responsible for any outcome related to the failure to comply with installation, usage or maintenance guidelines.
• Incorrect installation or use of the robot may cause serious damage to property or injuries to people.
• Do not enter pool while the robot is in water.

WARNINGS ON USE

• Only use the detachable supply unit provided with the robot to recharge the battery. Operate the power supply at least 3.5 meters from edge of pool.
• Disconnect the robot from the power supply and insert the magnetic cap back in place before performing any maintenance on the robot.
• Do not operate the robots with wet hands.
• Disconnect the robot from the power supply before carrying out user maintenance.
• Do not try to repair the robot yourself or open engine box in case of malfunction, please contact your dealer.
• If there is any malfunction or release of odor from the robot when charging, disconnect it from the power supply immediately and contact your dealer.
• Use only original replacement parts supplied by the manufacturer for service and repair.

GENERAL OPERATION CONDITIONS

• i. Water depth range: 0.4-3m
• ii. Water temperature: between 4℃~35℃ (below 15℃, the endurance time may be affected)
• iii. PH: 7.0-7.8
• iv. NaCl: 5000 PPM,MAX
• v. Chlorine: 4 PPM, MAX
• The robot will automatically stop running if the water depth is less than 40 centimeters for the purpose of motor protection.
• Do not use the robot during shock chlorination.
• Do not use the robot in thunderstorm or stormy weather.
• Do not expose the robot to direct rainfall or sunlight for an extended period.

CAUTIONS

• Rest/hold the robot by the pool edge for water to drain out before lifting the robot out of water, do it slowly so as to prevent back injury.
• Clean the filter basket after each cleaning cycle.
• Do not lift the robot out of water by track.

REMINDER

• When the robot battery is below 30%, it will only clean the floor of the pool.
• a. Storing your robot:
  • i. Ensure the robot is fully dry before storage. This prevents degradation or damage to the motors or internal structure.
  • ii. The filter basket should be cleaned thoroughly after usage and do not leave dirt or debris to dry in filter basket.
  • iii. The charger cable is stored neatly without twists whilst in long term storage
• b. Optimum storage temperature between -10-45℃ and storage humidity between 30%-70%/RH.

PRODUCT OVERVIEWS

Packaging content
The following items are included in the packaging of robot. Please contact your dealer if any damage or loss.

1. The robot
2. Charger
3. Hook
4. Magnetic cap*2
5. User manual

Note:

1. Remove the Magnetic cap ④ when using or charging. Insert Magnetic cap to machine’s bottom for battery protection when not using the robot for more than 14 days.
2. If the robot fails, insert the Magnetic cap ④ into the robot for 2 seconds, remove the magnetic cap and restart the robot, i.e., reset the robot.

Technical specification

Performance condition reference: Floor mode
Endurance time| 8h| 6h| 4.5h| 3h
Performance condition reference: Floor/wall/waterline mode
Endurance time| 4.5h| 3.5h| 2.5h| 2h
Charging time| 5h| 4h| 3h| 2h
Battery| 14Ah (352wh)| 10.4Ah (262wh)| 7.8Ah (196wh)| 5.2Ah (131wh)
Optimum pool temperature| 4~35℃
Cleaning mode| Floor only /Floor, Wall&Waterline
Multiple cycle option| 0.5h/1h/2h Full Run
AI Timer| Clean every 24h / 48h / 72h
App application| YES
Filter capacity| 3.2L
Filtration accuracy| 180μm
Pump flow rate| 22-10(m³/h)| 20-10(m³/h)
Running power| 30-110W
Moving speed| 12m/min
Number of motors| 3
Charger input| 90-265VAC ~ 50/60Hz
Running voltage/current| 25.2V/1.2A
Charger power| 72.5W
Robot NW/GW| 12 / 17kg| 12 / 17kg| 11.5 / 16.5kg| 11.5 / 16.5kg
Robot dimension (LWH)| 495395265 mm
Robot packaging dimension

(LWH)

| 580448330 mm

• Reference : Above working time is based on 2 hours’ cleaning each time at floor mode in the liner pool.
  Note : The manufacturer reserves the right to modify these specifications without notice.

① Remove the Magnetic cap from the bottom of the robot and store it well.

| ② Remove the plug cover. When fully charged, cover the plug again.

---|---
③ Connect to the power(90-265V) supply using the charger supplied.

The red light indicates charging;

The green light indicates power and a fully charged robot;

Fully charge the robot before the first use.

*Suggested Charging Temperature: 6-35℃

| ④ Install the configured hook on the rod (Rod is exclusive).

OPERATION

CAUTION
To prevent possible damages to the robot or people, be sure to follow these guidelines:

• a. After cleaning is completed, place the robot in a cool dry place away from direct sunlight
• b. Take care when moving robot from pool and allow water to drain from robot before lifting.

IMPORTANT

• Once the robot is set up, drop into the water within 3 minutes or the robot will enter sleep mode.

• Clean the filter basket after the cleaning cycle. Avoid cleaning the surface of the filter box directly with your hands.

• The robot has a safety feature that automatically stops if a dry run happens.

• Turn the robot in all directions to release any air trapped in the robot before it enters the water. Shown below.

Overview of Control Panel

Operation on the display of the unit

1. Hold for 3 seconds to activate the robot. When flashes, start robot set up. After setup, press again for confirmation. Once completed, put the robot into the water. The robot will start cleaning automatically when it touches the floor. If there is no operation from the robot within 3 minutes as the flashes, the robot will shut down and enter sleep mode.
   *Note: There are two different outcomes when setting up the AI Timer:
   (Take set of ” Cleaning every 24 hours” in AI Timer for example)
   a. Press once and put the robot into the water. The robot will start immediately. After one clean cycle, the robot will enter sleep mode and automatically wake up after 24 hours.
   b. Press for 3s and then put the robot into the water. The robot will enter sleep mode. After 24 hours, the robot will automatically wake up and start cleaning.

2. If the battery is less than 15% during the cleaning cycle , will keep flashing red light, and the robot will self-park at the edge of the pool. It will enter sleep mode after 5 minutes.

Cleaning the filter basket
When a cleaning cycle is completed, the robot will self-park at the edge of the pool. Use the hook to catch the handle and lift the robot out of the water, drain the water from the robot and clean the filter basket as shown below:

Note:
To prevent injury, wear rubber gloves when cleaning the filter basket.

Charging the robot

1. Plug the adapter into power supply and make sure that indicator light is being red.
2. Open the cover of the robot’s plug to expose the plug charging port.
3. Plug the adapter plug into the robot. When the robot is charging, the battery light of the robot flashes green and the indicator light on the adaptor is red.
4. If the battery bar indicator is full with 3 green lights on, and indicator light of the power adapter will also turn green, then the robot is fully charged.
5. Before charging, make sure charging port is dry.
6. Disconnect the charger after charging is completed to protect the battery.
7. If the robot needs to be stored for long time, it should be fully charged at least every three months to protect the battery.
8. It is not recommended to charge outdoors.
9. Note: Use the original power adaptor with the robot ONLY.

WIFI Matching

• Hold for 3s, then the robot will have a beep sound, the robot enters matching mode, start flashing, open the “AI-BOT” APP to search device and match the robot to your network and go matching, the robot will beep three times and will turn green after network is matched.
• Setup of the robot can be operated via the APP using Wifi or Bluetooth.
• Setup of the robot cannot be operated by APP if the robot is in the pool. (Due to the physical limitation of radio signal penetration in water).
  Note : download the “AI-BOT” APP in iOS App Store/ Google Play Store.

MAINTENANCE

WARNING

1. To avoid electric shock and other hazards which could result in major injuries, disconnect the adapter from the power source before performing any cleaning and maintenance.
2. Before any maintenance, insert the magnetic cap at the bottom of the robot to avoid injuries caused by impeller rotation.

Filter maintenance

1. Clean the filter thoroughly and regularly for a better cleaning and climbing performance. Otherwise, the cleaning and climbing performance may be affected when the filter is full or clogged.
2. Annually clean the clogged filter with mild acidic detergent, Suitable safety equipment must be worn when carrying this out.

Impeller maintenance
Visually check whether the impeller or impeller shaft is entangled with hair or other debris when the robot has a reduced suction or climbing performance, clean the debris trapped in the impeller.
*Magnetic cap MUST be inserted into the robot before any maintenance on the impeller.

Follow the below steps:

1. Take out the filter box, remove the fixing screws of the inflow ring cover, and take out the inflow ring cover.
2. Remove the deflector fixing screws and take out the deflector.
3. Remove the impeller screw and take out the impeller. Note: Wear gloves when removing the impeller to prevent injury from sharp edges.
4. Clean the impeller debris and reassemble all the parts mentioned above in order.

Note : If you have any difficulties with impeller maintenance, contact your dealer for assistance.

Replace the worn brushes
Remove the worn brushes & position the new brushes:

1. Unfasten the tabs from the holes and remove the brushes.
2. Fit the side without tabs under the brush holder.
3. Roll the brush around its support, slide the tabs into the attachment holes and pull on the end of each tab until its edge passes through the slit.

Replace the worn tracks
Remove the worn tracks:

Position the new tracks:

TROUBLESHOOTING

Charging failure

| Debris on the electrode of charging

head (Non-failure)

| ****

Clean debris

The bottom Magnetic cap isn’t

removed  (Non-failure)

| ****

Remove the Magnetic cap

Charger is damaged| Replace charger

Switching on failure

| The Magnetic cap isn’t removed

(Non-failure)

| ****

Remove the Magnetic cap

Water spots on the robot display or people’s hand

(Non-failure)

| ****

Keep the display and hands dry, then try again

Wrong operation (Non-failure)| Hold the power button for 3 seconds
No power in the battery

(Non-failure)

| ****

Get the robot fully charged

Not working（not moving, not pumping）

| Low battery (Non-failure)| Get the robot fully charged

Out of water (Non-failure)

| Make sure the robot under water and indicator lights

being on

No pressing the on/off button after settings are done

(Non-failure)

| Press the on/off button after the settings are done, make sure indicator lights being on before putting the robot into

water

Full load of filter basket

(Non-failure)

| ****

Clean filter basket

Moving but not pumping

| ****

The impeller gets stuck

| Check whether there are too many debris in the guide ring, affecting the rotation of the impeller. (Please insert back the magnetic cap before operation, to avoid injuries

caused by the impeller rotation）.

Full load of filter basket

(Non-failure)

| ****

Clean filter basket

Water inlet is blocked(Non-failure)| Take out of filter basket and clean water inlet
Battery low (Non-failure)| Get the robot fully charged

Pumping but not moving

| The moving motor gets stuck| Please contact the dealer for replacement
Track is deviated and stuck

(Non-failure)

| Turn the robot upside down and roll the track forward

and backward to restore the track

Track is damaged| Replace track
Scrubber gets stuck (Non-failure)| Clean scrubber
The robot gets stuck by obstacle

and shut down for auto-protection (Non-failure)

| ****

Remove obstacle and restart

 | Full load of filter basket

(Non-failure)

| Clean filter basket
---|---|---

Not climbing

| Under floor cleaning mode

(Non-failure)

| ****

Turn to overall cleaning mode

The impeller is stuck

| Check whether there are too many debris in the guide ring, affecting the rotation of the impeller. (Please insert back the magnetic cap before operation, to avoid injuries

caused by the impeller rotation).

Full load of filter basket (Non-failure)

| ****

Clean filter basket

Water inlet is blocked (Non-failure)| Take out of filter basket and clean the water inlet

Poor cleaning capability.

| Battery low (Non-failure)| Get the robot fully charged
The impeller is stuck| Remove any debris or hair in the guide ring
A full load of the filter basket

(Non-failure)

| ****

Clean filter basket

Water inlet blocked (Non-failure)| Take out of filter basket and clean the water inlet.
Scrubber is damaged| Replace scrubber
Filter basket is damaged| Replace filter basket
Unusual

non-stop

| ****

Software failure

| Insert the magnetic cap back to the bottom for 5s, then

remove it and restart

Note:

1. Do not use the robot when people or animals are in the pool.
2. Charger MUST BE DISCONNECTED before conducting any maintenance on the robot.
3. Contact your dealer for problems not covered in the Trouble Shooting Guide.
4. Normally, the robot will stop at the poolside when it encounters any failure or when the battery level is less than 15%.
5. If an error occurs, please restart the robot by placing the magnetic cap at the underside of the robot.
6. If the robot is malfunctioning, the error code will appear on the operation panel (see 2.1) and the power button on the operation and panel flashes red. Pressing the power button  will remove the error warning  and allow operation, if error occurs again, please check the troubleshooting guide.

Indoor For switch power supply indoor use only.

Recycling When disposing the product, please hand it over to a designated collection point for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of waste equipment at the time of disposal will help ensure that it is recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste for recycling, please contact your local authority.

Warranty Exclusions

Warranty is not valid if any of the following apply:

• Incorrect operation of the unit by not following correct instructions.
• Damage caused to the robot due to misuse or damage caused by any other means than manufacturer defect.
• If robotic pool cleaner is repaired or serviced by an unauthorized dealer or service station.
• If an unauthorized service station damaged battery seal.
• If you overcharge the battery by using a non-specified input power adapter.
• If you cause a fault in the operation of the machine by using non-specified accessories.
• General wear and tear of consumable products (Filter, Tracks, Brushes)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>