MLR FABRICATING E-ZLIFT Deluxe User Manual

MLR FABRICATING E-ZLIFT Deluxe

Product Information

MLR Fabricating LLC’s products are guaranteed to be free from defects in material and/or workmanship and to perform as advertised when properly assembled, used, and maintained in accordance withwritten instructions for a period of 24 months to the original purchaser. Failure to adhere to and/or comply with operation manual instructions will void all associated warranty obligations. Should any part(s) prove defective within 24 months from the date of purchase, it (they) will be repaired or replaced at our option F.O.B. our facility, without charge provided the defective part(s) is returned to our facility, transportation charges prepaid. MLR Fabricating will not be responsible for labor charges, loss, or consequential damage of any kind or character caused by defective parts or for charges incurred in the replacement or repair of inadequate parts by the purchaser. Improper installation or use may void all warranties. Due to the conditions & environment under which this product is used, MLR Fabricating LLC makes no oral, written, expressed or implied statement as to the safety of this device. The purchaser assumes all responsibilities and risks upon purchase. MLR Fabricating LLC will NOT be liable for loss, damage, injury or death arising from the use of this product.

Assembly Instructions

1. Remove the product from cartons and place it on a flat surface.
2. Position the lift so that the logos are facing outward.
3. Install 2 bridge assemblies using 1/4 x 1-3/4 bolts, flat washers, and lock nuts provided. Match up the numbers. (Snug bolts only for now)
4. Connect hoses to the 90-degree fittings on the cylinder. Do not use Teflon tape on these connections.
5. Fill the reservoir with oil. Non-synthetic automatic transmission fluid is recommended.
6. Using the remote, raise the lift to the upright position and tighten the bridge bolts. Install 1 riser block if needed.
7. We recommend using a Group U1 Lawn mower battery with a minimum of 300 cranking amps.
8. The air pressure on the back side of the piston (tank on the side of the cylinder) comes preset at 50 PSI on the left side and 70 PSI on the right side. This is the correct setting in 99% of cases. Refer to the operating instructions to learn how to adjust if needed.
9. Refer to the attached drawing for handle assembly (applicable for aluminum lifts only).

Thank you for choosing the E-Z Lift. If you have any questions or concerns, please get in touch with us.

PLEASE READ ALL INSTRUCTIONS FIRST!!
Do not over-tighten 1/4” bolts…10 ft-lbs is max torque!!!

THIS FORM MUST BE SIGNED & RETURNED FOR WARRANTY
TO BE ACTIVE

• MLR Fabricating LLC’s products are guaranteed to be free from defects in material and/or workmanship and to perform as advertised when correctly assembled, used, and maintained in accordance with written instructions for a period of 24 months to the original purchaser. Failure to adhere to and/or comply with operation manual instructions will void all associated warranty obligations.
• Should any part(s) prove defective within 24 months from the date of purchase, it (they) will be repaired or replaced at our option F.O.B. our facility, without charge provided the bad part(s) is returned to our facility, transportation charges prepaid.
• MLR Fabricating will not be responsible for labor charges, loss, or consequential damage of any kind or character caused by defective parts or for charges incurred in the replacement or repair of defective parts by the purchaser. Improper installation or use may void all warranties.
• MLR Fabricating LLC, must be notified of a failure within the warranty period and will then supply instructions to the Customer.

Due to the conditions & environment under which this product is used, MLR Fabricating LLC makes no oral, written, expressed or implied statement as to the safety of this device, The purchaser assumes all responsibilities
and risk upon purchase.
MLR Fabricating LLC will NOT be liable for loss, damage, injury or death arising from the use of this product .

• The foregoing states the MLR Fabricating LLC’s entire liability for any claim to damages whatsoever and is made by MLR Fabricating LLC and accepted by Purchaser in lieu of all other warranties, obligations, or liabilities expressed or implied.
• Please sign & return this copy to: MLR Fabricating LLC,2800 West CR 500N
  North Vernon, In 47265 to activate your warranty,
  I have read & agree to these terms

ASSEMBLY INSTRUCTIONS

1. Remove from cartons & place on flat surface.
2. Place the lift so that logos are to the outside.
3. Install 2 bridge assemblies with 1/4″ x 1-3/4” bolts flat washers & lock nuts provided, match up numbers. (snug bolts only for now)
4. Connect hoses to 90-degree fittings on the cylinder. (Do not use teflon tape on these connections)
5. Fill the reservoir with oil, non-synthetic automatic trans fluid is recommended
6. Using the remote raise the lift to an upright position & tighten bridge bolts Install 1″ riser blocks if needed.
7. We recommend a Group U1 Lawn mower battery with a minimum of 300 cranking amps.
8. Air pressure on the back side of the piston (tank on the side of the cylinder) comes preset at 50 PSI left side and 70 PSI right side, this is the correct setting 99% of the time, see operating instructions on how to adjust if needed.
9. See the attached drawing for handle assembly. (aluminum lifts only)

Thanks, for choosing the E-Z Lift, if you have any questions or concerns, please get in touch with us.
Larry Hartwell
812-592-2945 ● mlrfabricating@gmail.com
Caution!!! Make sure hoses are routed UNDER cross brace, as shown, failure to do so will damage lift & void warranty!!!

E-Z Lift Operating Instructions

1. Choose a spot that is as flat as possible.

2. The lift goes under the car with a hose attachment pointed to the rear.

3. Place Lift on the Ground & position car over lift with a hose to the rear.

4. Try to center lift left to right as close as possible on the frame rails.

5. For starting front to rear alignment put front lift points about 2 inches behind the bend in the frame rail. All cars are different because of the rear percentage make sure car is stable or move lift forward or backward as needed.

6. LEFT SIDE PERCENTAGE Lift should raise both sides of the car evenly, if you see the right side getting ahead of the left side, add 10 lbs air to right side, if more is needed remove 10 lbs from left side repeat as necessary to even out.

7. Grease all pivot points, (requires needlepoint) & spray cylinder pivots with spray lube, also spray cylinder shaft where it enters the cylinder to lube the o-ring.
   Repeat as necessary.

8. Raise the car, and drop the safety struts down into position. (Don’t forget to raise them back into an upright position before lowering unit)

9. Do not let lift rest on safety struts, they are there only in the event of a hydraulic failure.

10. Do not let the car down on lift with no tires on it, you will have to jack the car up to get the lift to work if you do. The lift needs the suspension active to lift the first few inches.

That’s it, enjoy your E-Z Lift!!

HANDLE ASSEMBLY

812-592-2945 ● mlrfabricating@gmail.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>