i-PRO WV-Q183 Corner Mount Bracket Instruction Manual

i-PRO WV-Q183 Corner Mount Bracket Instruction Manual

Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.

For U.S. and Canada:
i-PRO Americas Inc.
For Europe and other countries:
i-PRO EMEA B.V.
https://www.i-pro.com/

© i-PRO Co., Ltd. 2022 sL1217-2042 PGQX2197XA

Printed in China

Preface

Features

WV-Q183/WV-Q189 (corner mount bracket) is designed to be used to install a camera or mount bracket for camera to an external corner of building.
• WV-Q183 is different with WV-Q189 in color, and same in structure. This manual takes WV-Q189 as an example for explanation.

Parts and functions

(In this illustration, fixing WV-Q122A to a corner by using WV-Q189 is taken as an example.)

Specifications

Precautions

Refer installation work to the dealer.
Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to the product.
Be sure to consult the dealer.

The exclusively designed mount bracket shall be used.
Failure to observe this may cause a drop resulting in injury or accidents.
Use the exclusively designed mount bracket for installation.

Do not install this product in locations subject to vibration.
Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.

Install this product in a location high enough to avoid people and objects from bumping the product.
Failure to observe this may cause injury.

The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury.
If there is specified safety wire, please make sure to install it.

The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.

Select an installation area that can support the total weight.
Selecting an inappropriate installation surface may cause this product to fall down or topple over, resulting in injury or accidents.
Installation work shall be started after sufficient reinforcement.

Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.

Do not hang down from this product or use this product as a pedestal.
Failure to observe this may cause injury or accidents.

Do not use this bracket except with specified cameras or other brackets.
Failure to observe this may cause a drop resulting in injury or accidents.

Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall of this product may occur.

Do not install this product on a place that is greatly influenced by wind.
Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause a fall of the product resulting in injury or accidents.

Do not attempt to disassemble or modify this product.
Failure to observe this may cause a fall of the product resulting in injury or accidents.
Consult the dealer for the repair or inspections.

Do not rub the edges of metal parts with your hand.
Strong rubbing may cause injury.

The measures of protection against snowfall shall be taken.
Weight of snow may cause a fall of the product resulting in injury or accidents.
Protect the product against snowfall by installing under eaves.

Precautions for installation

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.

In order to prevent injury, the product must be securely mounted to the wall (corner) according to Operating Instructions.

Installation area for this product

• Please consider the influence of vibration and wind at the installation site and mount the bracket onto the wall with appropriate strength.
  Installable corner: Corner part of a vertical and right-angle wall

• Do not mount the product on a plaster board or a wooden section because they are too weak.
  If the product is unavoidably mounted on such a section, the section shall be sufficiently reinforced.

• After the bracket is mounted, please verify the following content once a year. In the event of abnormality, please inform the dealer.

• Do not allow any slanting, distortion or offset in installation.

• Bracket should not have any serious rust or damage.

• Please refer to our support website (https://i-pro.com/global/en/surveillance/training_support/support/technical_information) for installation information of the bracket.

About the installation methods

• The bracket is specifically designed for installation onto a corner of the wall.

• Prepare mounting screws (M8 8 pcs.) and anchor bolts to be mounted on a wall separately.

• Select screws according to the material of the location that the bracket will be mounted to.
  Minimum pull-out strength: 823 N {185 lbf} (per 1 pc.)

• After the installation is finished, please check if there are slackness or shaking of screws and raising of mount bracket.
  In the event of abnormality, please tighten again.

Check before the installation.
Once the bracket is installed with a deformed mount bracket and/or damaged part, it could potentially fall. Before the installation, please make sure to check the appearance of the bracket.

Do not place this product in the following places:

• Locations where a chemical agent is used such as a swimming pool.
• Locations that have a specific environment that is subject to an inflammable atmosphere or solvents.
• In areas by the sea or the seashore, regions with snow melt agent scattered and locations that produce a corrosive gas such as volcanic areas and hot springs.
• Locations where the ambient operating temperature of camera is not within the specified range.
• Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines.
  (This bracket is not designed for on-vehicle use.)

Screw tightening

• Make sure to tighten the screws (accessory) that fix camera or mount bracket onto WV-Q183/WV-Q189.
• Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively.
• When a screw is tightened, make the screw at a right angle to the surface. After tightening the screws or bolts, perform checks to ensure that the tightening is sufficient enough so that there is no movement or looseness.

Make sure to remove this product if it will no longer be used.

Installations/Connections

Standard accessories