i-PRO WV-Q186 Mount Bracket Instruction Manual
- June 12, 2024
- i-PRO
Table of Contents
i-PRO WV-Q186 Mount Bracket Instruction Manual
Model No. WV-Q186
Before attempting to connect or install this product, please read these
instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
For U.S. and Canada:
i-PRO Americas Inc.
For Europe and other countries:
i-PRO EMEA B.V.
https://www.i-pro.com/
Preface
Features
WV-Q186 (mount bracket) is designed to be used to install a fisheye camera or
a dome camera for outdoor use in the following ways.
• When installing on a wall using together with WV-Q185 (wall mount bracket)
Precautions
Refer installation work to the dealer.
Installation work requires technique and experiences. Failure to observe this
may cause fire, electric shock, injury, or damage to the product.
Be sure to consult the dealer.
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in
injury or accidents.
Consult the dealer for the inspections.
The exclusively designed mount bracket shall be used.
Failure to observe this may cause a drop resulting in injury or accidents.
Use the exclusively designed mount bracket for installation.
The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
Select an installation area that can support the total weight.
Selecting an inappropriate installation surface may cause this product to
fall down or topple over, resulting in injury or accidents.
Installation work shall be started after sufficient reinforcement.
Do not install this product in locations subject to vibration.
Loosening of mounting screws or bolts may cause a fall of the product
resulting in injury or accidents.
Install this product in a location high enough to avoid people and objects
from bumping the product.
Failure to observe this may cause injury.
The measures of protection against snowfall shall be taken.
Weight of snow may cause a fall of the product resulting in injury or
accidents.
Protect the product against snowfall by installing under eaves.
Avoid installing this bracket in the locations where salt damage occurs or
corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall
of this product may occur.
Do not hang down from this product or use this product as a pedestal.
Failure to observe this may cause injury or accidents.
Precautions for installation
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
Take notice of humidity.
Install this product when the humidity is low. If installation is performed
when it is raining or in very humid conditions, the inside may be affected by
humidity, causing mist-over inside the camera.
Mounting method for this product
This product is designed to be used as a pendant mount camera. If the product
is mounted on a desktop or at a slant, it may not work correctly and its
lifetime may be shortened.
Do not place this product in the following places:
- Locations where a chemical agent is used such as a swimming pool
- Locations subject to moisture or oil smoke such as a kitchen
- Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
- Locations where radiation, an x-ray, a strong radio wave, or a strong magnetic field is generated
- Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases such as from hot springs, volcanic regions, etc.
- Locations where the temperature is not within the specified range (The ambient operating temperature of the installed camera.)
- Locations subject to condensation as the result of severe changes in temperature (In case of installing the product in such locations, the inside of camera may become foggy or condensation may be caused in the camera.)
- Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not designed for on-vehicle use.)
Specifications
Standard accessories
Operating Instructions (this document)……………………………………………………………………………… 1 set
Ⓐ Inner cover………………………………………………………………………………………………………………. 1 pc.
Ⓑ Screw (Fixing screw for the inner cover: M3)………………………………….. 4 pcs. (of them,
1 for spare)
Required parts other than the above
• Accessories provided with the camera to be installed
Attachment plate…………………………………………………………………………………………………….. 1 pc.
Fixing screws for attachment plate (M4 × 8 mm {5/16 inches})……………………………………… 5
pcs. (of them, 1 for spare)
Parts and functions
Do not install this product on a place that is greatly influenced by
wind.
Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or
more may cause a fall of the product resulting in injury or accidents.
Do not use this bracket except with specified cameras.
Failure to observe this may cause a drop resulting in injury or accidents.
Do not rub the edges of metal parts with your hand.
Strong rubbing may cause injury.
Screw tightening
• Do not use an impact driver. Use of an impact driver may damage the screws
or cause tightening excessively.
• When a screw is tightened, make the screw at a right angle to the surface.
After tightening the screws or bolts, perform checks to ensure that the
tightening is sufficient enough so that there is no movement or looseness.
Protection from lightning
When cables are used outdoors, there is a chance that they may be affected by
lightning. In such a case, install a lightning arrestor close to the camera,
and make the length of the network cable between the camera and lightning
arrestor as short as possible to prevent the camera from being damaged by
lightning.
Make sure to remove this product if it will no longer be used.
Network Camera: WV-SFV631LT, WV-SFV631L, WV-SFV611L, WV-SFV531, WV- SFV311A, WV-SFV310A, WV-S2531LTN, WV-S2531LN, WV-S2511LN, WV-SFV481, WV-SW458 CCTV Camera: WV-CW634S, WV-CW634SE, WV-CW634F, WV-CW630S/G, WV-CW364SE, WV- CW334SE
Installations/Connections
[1] Fix WV-Q185 (wall mount bracket) on a wall and attach the cover of WV-Q186 (mount bracket) to the WV-Q185
[2] Fix the cable with the inner cover of WV-Q186
[3] Attach the attachment plate to the cover part of the WV-Q186
- The upper right illustration is provided as an example of attaching the attachment plate for a camera model having three attachment mounting screws.
[4] Making connections
< When waterproof treatment is applied to RJ45 connector and other
cables>
Adequate waterproof treatment is required for the cables when installing the
camera with cables exposed. The camera body is waterproof, but the cable ends
are not waterproof. Be sure to use the waterproof tape provided with the
camera at the points where the cables are connected and apply waterproof
treatment in the following procedure. Failure to observe this or use of a tape
other than the provided waterproof tape (such as a vinyl tape) may cause water
leakage resulting in malfunction.
Separately apply waterproof treatment to the network cable and other cables as shown in the illustration below.
IMPORTANT:
< If RJ45 waterproof connector is used>
Connect an Ethernet cable (category 5e or better, straight) to RJ45 plug
(locally procured).
IMPORTANT:
• If the procedure for the RJ45 waterproof connector (provided with the
camera) part is not correctly followed, the waterproofing may be compromised.
Do not install the camera where the RJ45 waterproof connector is exposed to
constant rain or moisture.
• When you remove the RJ45 waterproof connector, be sure to follow the reverse
order of the connecting procedures. (The RJ45 waterproof jack may be damaged
when you try to remove the RJ45 waterproof connector cover with its “⇦” mark
matching “▶” mark of the RJ45 waterproof jack.)
[5] Fix the camera to the attachment plate
① After connecting the cables to the camera, align the OPEN mark at the side
of the camera enclosure to the claw of the attachment plate (provided with the
camera). Then, insert the attachment mounting screws (2 or 3 points) at the
bottom of the camera into the holes of the attachment plate.
After that, move the LOCK mark to the point where the claw of the attachment
plate is located by rotating the camera body clockwise by approx. 15° to fix
temporarily.
- Refer to the operating instructions of the connected camera for information on how to mount the camera.
IMPORTANT:
• When using WV-SFV481 or WV-SW458 with a SD memory card, insert the SD memory
card to the camera before mounting the camera onto the WV-Q186.
< For WV-SW458>
Tighten the camera fixing screw located at the enclosure of the camera to fix
the attachment plate and the camera. (Recommended tightening torque: 0.78 N·m
{0.58 lbf·ft})
IMPORTANT:
• Enclosure is fixed at the installation auxiliary wire to the camera body,
please do not remove the installation auxiliary wire.
Note:
• As for the enclosure fixing screw, there are three screws models and four
screws models depending on the camera model.
Refer to the operating instructions of the camera for further information.
2. Adjust images from the camera.
- Refer to the operating instructions of the camera for further information on how to adjust.
3. After completing the adjustment, attach the enclosure back to the original position and fix it with the enclosure fixing screws (3 or 4 screws).
IMPORTANT: This caution shall be applied to all the cameras as described
above.
• Be sure to tighten the camera fixing screw. Failure to observe this may
cause camera trouble due to camera falling.
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
© i-PRO Co., Ltd. 2022 sL1017-2042 PGQX2198XA Printed in China
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>