TTQ B0C76XH4T3 Wireless Lavalier Microphone User Manual

TTQ B0C76XH4T3 Wireless Lavalier Microphone

PACKAGE LIST

• Charging Case

• Transmitter x2

• Receiver

• Instruction

• Storage Bag

• Charging Cable x 1

• Headphone Cable x2

• Type-C Adapter Ca

• iPhone Adapter Cable

• Camera Adapter Cable

• Cindproof Cover x2

PRODUCT FEATURES

Transmitter

① In-built Mic
② Power Button (Press for 3s to Switch On/Off, One Click to Mute/Unmuted, Double Click to Bluetooth On/Off, Press 5 times for Reset)
③ Channel Selection Button (One Click for Cyclic Switching from Noise Reduction / Original Sound / Reverb Mode, Default Noise Reduction Mode)
④ Indicator (Red light flashes when power below 30%, Blue light is always on power above 30%)
⑤ Mute Indicator
⑥ Connectivity Indicator (Pairing—Blue Light On, Unpairing—Blue Light Flash)
⑦ Channel Selection Indicator (Blue—Notice Reduction, Red—Reverb, Green—Original Sound)
⑧ Bluetooth Indicator
⑨ 3.5mm TRS Input
⑩ USB-C Connector

Note: (Right device is TX 1, Left device is TX 2)

Receiver

① Power Button (Press for 3s to Switch On/Off, One Click to Screen On/Off, Double Click to Dodge Mode On/Off, Press 5 times for Reset)
② Volume Button ( 5 levels available, default 4)
③ Transmitter Switch Button (Press transmitter switch button to select TX 1 or 2, and dou1ble-click volume button to mute/ unmute corresponding device, or one-click volume button to volume up corresponding device)
④ Power Indicator (Red light flashes when power below 30%, Blue light is always on when power above 30%)
⑤ 3.5mm TRS Output
⑥ USB-C Connector
⑦ Display Screen

① Mode Status

Blue light indicates on, gray light indicates off.
BT-Bluetooth Accompaniment Mode: Another phone connects to the Bluetooth and then plays the audio source as the accompaniment
DODGE-Dodge Mode: The mic automatically adjust the volume of background music when you are talking or not.
NC-Noise Reduction mode
OST-Original Mode
REB-Reverb Mode
② Two Transmitter Working State
③ Power Status and Signal Status of 1 RX and 2TX

Charging Case

Power Indicator of Charging Case Open the case, check out light indicator

>   S30%| | Red light flashes for 3s
---|---|---
30%< S70%| | Alternating red and green lights flash for 3s
70°/o< S99%| | Green light flashes for 3s
=100%| | Green light lights on 3s

Power Indicator of Device Charging Status
Close the case, check out light indicator
RT and XT are charging, red light lights on
RT and XT are fully ch1arged, lights off

Power Indicator of Case Charging Status
Insert Type-c cable, check out light indicator
Case are charging, red light flashes
Case are fully charged, red light lights on

CONNECTIVITY

1. Open case, take out RX and TX

2. Connect RX with phones or camera

3. RX and TX will be pairing automatically. If not, press 5 times Power Button of RX and TX for reset.

PRODUCT PARAMETERS

Charging Case

RX/TX:

NOTES

1. Please disconnect the charger and turn off the product before cleaning.
2. Don’t disassemble or put any object or liquid into the equipment to avoid causing machine failure
3. Don’t place the equipment in the sunlight to avoid early aging of electronic parts.
4. Avoid the use of dusty or dirty environment (dust can easily cause equipment failure)
5. Don’t exceed the ambient temperature of -10 °C-40 °C and relative humidity of 10%-95°/o.
6. Avoid friction impact with hard objects to cause surface scratches, peeling or other hardware damage.

CUSTOMER SUPPORT

If encounter any problems in using the product or need any help,
please contact us to get more technical support :
ttq-vip@outlook.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>