Russell Hobbs 27290-56 Satisfry Dual Basket Air Fryer User Manual

Russell Hobbs 27290-56 Satisfry Dual Basket Air Fryer User Manual

Read the instructions, keep them safe, pass them on if you pass the appliance on. Remove all packaging before use.

IMPORTANT SAFEGUARDS

Follow basic safety precautions, including:
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved.

Children must not play with the appliance. Cleaning and user maintenance must not be done by children unless they are older than 8 and supervised. Keep the appliance and cable out of reach of children under 8 years.

Don’t connect the appliance via a timer or remote control system.
Don’t use the appliance near or below combustible materials (e.g. curtains).

The surfaces of the appliance will get hot.

Do not immerse in any liquid.

If the cable is damaged, return the appliance, to avoid hazard.

• Don’t use accessories or attachments other than those we supply.
• Don’t use the appliance for any purpose other than those described in these instructions.
• Don’t operate the appliance if it’s damaged or malfunctions.
• Don’t use anything metal or sharp, you’ll damage the non-stick surfaces.
• Keep clear of the vent at the rear of the appliance hot air will come from it.

HOUSEHOLD USE ONLY

PARTS

• 1. Touch controls and display
• 1. Body
• 1. Crisping plates
• 1. Baskets
• 1. Basket dividers
• 1. U-channel connector

BEFORE USING FOR THE FIRST TIME

• Handwash the removable parts, rinse, and dry.
• When using your air fryer for the first time, you may notice smoke or a slight odour for the first few minutes of cooking. This is normal. Ensure the room is well ventilated.
• Place the crisping plates into the baskets. Slide the baskets into the body.

PREPARATION

• Sit the appliance on a stable, level, heat-resistant surface.
• Leave a space of at least 50mm all-round the appliance.
• Have oven gloves (or a tea towel) on hand, use heat resistant plastic tongs and a heat-resistant mat or dinner plate to rest the basket on.
• Note: Do not use metal tongs as it may scratch the coating. We recommend using only heat resistant plastic or silicon coated tongs.

CRISPING TRAYS

Fit the crisping trays into the bottom of each basket before fitting the basket dividers or joining the baskets together. Insert the front edge of the crisping tray under the curved projections that are along the inside edge of the basket as shown (Fig. 1). Press the back edge down to seat the crisping tray into the basket. Make sure that the trays are fitted correctly so that they don’t fall out if the basket is tipped.

ASSEMBLING THE BASKETS

To use one large basket

1. Remove the baskets from the body.

2. If present, slide the basket dividers out of each basket.

3. If they are not already fitted, fit a crisping plate into each basket.

4. Place the baskets side by side so that they are touching and aligned with each other (A).
   

5. Align the U-channel connector with the grooves on both sides of the baskets simultaneously and slide it partway into the basket (B).
   

6. Apply gentle outward pressure with your thumbs onto the top of the connector (C). Slide the connector downwards while maintaing the outward pressure. This will keep the connector aligned with the grooves on the inside of the basket.
   

7. Continue until the connector clicks into place.

8. If the connector binds up or jams when it is near to its final position, use your fingers to gently pull the bottoms of the baskets against your body (D). This will help to keep them aligned.
   

   • Don’t force anything. It should only require gentle/moderate pressure to install the basket connector,. Forcing it to fit might cause damage. If it doesn’t fit correctly, remove it and then check that the baskets are still in contact and aligned with each other, then try again.

To use two separate baskets

1. 1. Remove the baskets from the body.
   2. If present, remove the basket connector (E).
   
   3. Separate the baskets (F).
   
   4. Insert the crisping plates if you are using them.
   5. Orient each basket divider so that:

   • the arrow on the divider is pointing downwards.
   • The folded-over part on the top edge of each divider is facing outwards (see figures G and H).
     
     

2. Slide the divider into the basket slot.

3. Repeat for the other basket.

Note: If you don’t orient the basket dividers correctly (step 5) before fitting, they will fall out when the baskets are inverted.

Scan this QR code for a video showing how to assemble the baskets.

References

• Welcome to Russell Hobbs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>