Natural fit Saddle for CARBON Frames User Manual
- June 12, 2024
- Natural fit
Table of Contents
ASSEMBLY AND OPERATING INSTRUCTIONS
FOR SEAT WITH CARBON FRAME
Saddle for CARBON Frames
Read this document in your language
GENERAL INFORMATION
READ AND KEEP THESE INSTRUCTIONS IN A SAFE PLACE
These and other enclosed instructions contain important information on the
installation, commissioning and care of the product.
Carefully read all enclosed instructions, especially the general safety
instructions, before mounting or using the product.
Failure to follow the information in the enclosed instructions may result in
serious injury or damage to the product itself and your vehicle.
Keep the enclosed instructions on hand for further use. If you pass on the
product or the vehicle equipped with it to a third party, always include all
associated instructions.
We at CUBE strongly recommend that you have this product assembled by your
specialist dealer.
The enclosed instructions are subject to European legislation. If the product
or vehicle is delivered outside Europe, supplementary instructions may have to
be included by the manufacturer/importer.
EXPLANATION OF SYMBOLS
The following symbols and signal words are used in the enclosed instructions,
on the product or on the packaging.
WARNING!
Hazard with a medium degree of risk, which may result in death or serious
injury if not avoided.
CAUTION!
Hazard with moderate degree of risk, which may result in moderate or minor
injuries if not avoided.
NOTE!
Warning of possible damage to property.
Useful additional information on assembly or operation.
Read and follow the enclosed instructions.
Reference to further documentation – see the instructions (doc. number)
Use a torque spanner. Use the tightening torque indicated in the symbol.
Example of incorrect assembly.
Example of correct assembly.
Maximum load of the seat. Do not exceed the weight indicated in the symbol.
Particularly safety-relevant information.
INTENDED USE
This product is intended for mounting on approved vehicles only. Only
compatible and approved accessories with an appropriate contact point may be
mounted on this product. If you are uncertain, contact your dealer.
Use the product only as described in these instructions. Any other use is
considered improper and can lead to accidents, serious injury or damage to the
vehicle. The product is not a toy. The manufacturer or dealer assumes no
liability for damage caused by improper or incorrect use.
Exclude the following misapplications to avoid hazards:
- Improperly performed assembly and/or maintenance work, especially exceeding the maximum clamping ranges and incorrect tightening torques.
- Exceeding of the maximum permissible total weight.
- Above-average use in difficult terrain or frequent load peaks due to springing into the saddle when driving over obstacles.
- Weather conditions that are too hot or too cold.
- Improperly performed cleaning and maintenance work
- Lifting the bike by the saddle when the total weight is high, e.g. due to loaded panniers.
- Wearing garments that can damage the outer material, e.g. trouser buttons, zips in the seat area, jewellery or purse chains.
SAFETY INFORMATION FOR ACCESSORY PARTS
WARNING!
Risk of accidents and injury!
Read all safety information and instructions. Failure to comply with the
safety information and instructions can cause accidents, serious injuries and
damage.
Safety of children
If children play with the packaging or small parts, they can choke on them and
suffocate or injure themselves.
- Keep small parts away from children.
- Do not let children play with the packaging or the product.
- Do not leave the product and the vehicle unattended during assembly.
Safety information for installation
-
Before installation, check the delivery scope of the product for completeness.
-
Before installation, check all the components of the product and the vehicle for damage, sharp edges or burrs.
-
If the delivery scope of the product is incomplete or if you discover any damage, sharp edges or burrs on the components or the vehicle, do not use it.
-
Have the product and the vehicle checked by your specialist dealer.
-
Only use the intended parts and accessories for the product. Components from other manufacturers may impede its proper functioning.
-
If you would like to combine this product with a vehicle from another manufacturer, please check the vehicle specifications and dimensional accuracy and compatibility in accordance with the specifications in the accompanying manual and instructions for your vehicle.
-
It is imperative that you observe the manufacturer’s instructions for the seat post and the compatibility of the clamping area of the seat post with the respective cross-section of the seat frame.
-
Screw connections must be properly tightened to the correct tightening torque values using a torque wrench.
-
If you are inexperienced in using a torque wrench or do not own a suitable torque wrench, have the screw connections checked by your specialist dealer.
-
Observe the specific torque values for aluminium or carbon fibre reinforced plastic (CFRP) components.
Also read and observe the relevant information in the instruction manual for your vehicle. -
After mounting, check the seat for tight fit. If the seat does not fit tightly after mounting, it is unsuitable for the respective seat post.
Safety information for operation
Note that accessories can greatly influence the characteristics of the
vehicle.
Overloading the product may result in material damage.
Safety-relevant components can break or fail and lead to accidents and
injuries.
- Never exceed the maximum permissible total weight of the seat.
- Creaking or squeaking noises while riding can indicate a loose connection between the frame and the seat shell. First check the correct fit of the seat according to the installation instructions in order to be able to exclude faulty installation as a source of noise.
- Cold temperatures can make the seat more susceptible to stress peaks. Pay particular attention here to a cycling style that is appropriate for use.
- If you are not absolutely sure or if you have any questions, contact your dealer.
- After a fall, all components must be checked for damage and replaced if necessary.
- The enclosed instructions cannot cover every possible combination of the product with all vehicle models.
Safety information for maintenance
Prevent malfunctions due to excessive wear, material fatigue or loose screw connections:
- Check the product and your vehicle regularly.
- For safety reasons, seats with carbon frames must always be replaced after a mileage of 15,000 km.
- Do not use the product or your vehicle as a whole if you notice excessive wear or loose screw connections.
- Do not use the product and your vehicle if you notice cracks, deformations or changes in colour.
- Have the vehicle checked immediately by your specialist dealer if you notice excessive wear, loose screw connections, deformations, cracks or changes in colour.
- In the event of visible deformations, indentations caused by sharp edges of the seat post mount or cracks forming on the seat frame, the seat must be replaced for safety reasons. Particularly in the case of seats with carbon frames, the seat must be replaced if there are visible or suspected structural changes.
CLEANING AND CARE
NOTE!
Risk of damage!
Improper handling of cleaning agents can cause damage to the product.
- Do not use aggressive cleaning agents, brushes with metal or nylon bristles or sharp or metallic cleaning objects such as knives, hard spatulas and/or the like.
- Do not use solvent-based cleaning products such as oils or creams, these can wear down the seat’s upper material or cause it to come off.
- Perspiration can attack the upper material of the seat.
Clean the product regularly with water (add a mild detergent if necessary) and a soft cleaning cloth.
ACCESSORIES
Your seat has a screw mount in the rear area of the seat pan for various
accessories such as panniers or water bottle holders. Please observe the
operating instructions for the respective accessories when mounting.
TECHNICAL DATA
ACID bicycle saddles are approved for a maximum permissible total weight.
The maximum permissible total weight is calculated from your own body weight
including clothing, equipment worn on the body and accessories attached to the
seat.
(Cyclist + backpack (luggage) + helmet + accessories on seat + etc.)
STORAGE
All parts must be completely dry before storage.
- Always store the product in a dry place.
- Protect the product from direct sunlight.
DISPOSAL
Dispose of the packaging according to type. Put cardboard and carton in the
waste paper collection, foil and plastic parts in the recyclables collection.
**** Dispose of the product in accordance with the laws and regulations in
force in your country.
LIABILITY FOR MATERIAL DEFECTS
If any defects should occur, contact your specialist dealer from whom you
purchased the product.
To ensure that your claim is processed smoothly, you will have to provide
proof of purchase and inspection certificates.
Therefore, keep them in a safe place.
To ensure a long service life and durability of your product or vehicle, it
must only be used in accordance with its intended purpose. Be sure to observe
the information in the operating instructions for your vehicle.
In addition, the assembly instructions (especially torques for screws) and the
prescribed maintenance intervals must be observed.
Wear and tear of the graphics and colouring is not covered by the warranty as
it takes place due to UV rays, wear and tear, sweat and heat.
FOR FURTHER INFORMATION
Please visit us occasionally on our website at www.CUBE.eu. There you will fi
nd news, information and the latest versions of our operating instructions, as
well as the addresses of our specialist dealers.
Pending System GmbH & Co. KG
Ludwig-Hüttner-Str. 5-7
95679 Waldershof
Germany
+49 9231 97 007 80
www.cube.eu
FRAME TYPE| FRAME
CROSS-SECTION/MASS| MAX. PERMISSIBLE TOTAL WEIGHT| MAX. TIGHTENING TORQUE
---|---|---|---
Seat with carbon frame| High-oval / 9 x 7mm| 100 kg| Max. 7 Nm
ASSEMBLY AND OPERATING INSTRUCTIONS for seat with carbon frame
SEAT WITH CARBON FRAME 
NONE OF THE CLAMPING
ELEMENTS MAY EXCEED THE MAXIMUM RANGE (ILLUSTRATIONS ABOVE).
MAKE SURE THAT THE FRAME IS CORRECTLY SEATED IN THE SEAT POST (ILLUSTRATIONS
BELOW).
AS OUR CARBON FRAMES ALREADY HAVE A SPECIALLY COATED SURFACE IN THE CLAMPING
AREA, NO ADDITIONAL ASSEMBLY PASTE IS NECESSARY.
SHARP EDGES OR
INCORRECT ASSEMBLY CAN CAUSE SERIOUS DAMAGE TO THE FRAME.
ASSEMBLY AND OPERATING INSTRUCTIONS for seat with carbon frame 
AS A BASIC ADJUSTMENT BEFORE THE FIRST RIDE, WE RECOMMEND USING THE REAR
ADJUSTMENT RANGE OF THE SEAT FRAME (2) AND ADJUSTING THE ANGLE OF THE SEAT
SLIGHTLY DOWNWARDS (1).
PENDING SYSTEM GMBH & CO. KG
Ludwig-Huttner-Str. 5-7
D-95679 Waldershof