i-PRO WV-X5550LTPJ Network Camera Installation Guide
- June 12, 2024
- i-PRO
Table of Contents
WV-X5550LTPJ Network Camera
Product Information:
- Product Name: Network Camera
- Model Number: WV-X5550LT
- Intended Use: Professional use only
- Outdoor Use: Yes
- Manufacturer: i-PRO Co., Ltd.
- Authorized Representative in EU: i-PRO EMEA B.V.
- Manufactured in: China
Product Usage Instructions:
-
Installation:
-
Ensure that the power is turned off before installing the
camera. -
Avoid installing the camera in inflammable atmospheres.
-
Avoid locations where salt damage occurs or corrosive gas is
present. -
Do not use the camera near water or any foreign objects, as it
may cause fire or electrical shock. -
If you need assistance with installation, contact qualified
service personnel.
-
-
Operation:
-
Refer to the user manuals and online support resources for
information on camera settings and operation. -
Avoid direct eye exposure to the infrared (IR) emitted by the
camera. Use appropriate shielding or eye protection. -
Do not attempt to disassemble or modify the camera. Contact the
dealer for repairs or inspections. -
Avoid touching the camera, power cable, or connected cables
during thunderstorms to prevent electric shock.
-
-
Disposal:
- For European Union and countries with recycling systems, follow
the local regulations for disposal of old equipment and
batteries.
- For European Union and countries with recycling systems, follow
-
Additional Information:
-
For further support and technical information, visit the
manufacturer’s support website. -
For customers in the United States, contact i-PRO Americas Inc.
for support. -
For customers in Europe and other countries, contact i-PRO Co.,
Ltd. or i-PRO EMEA B.V. for support. -
Refer to the user manual for the model number and serial number
of the camera.
-
Installation Guide
Included Installation Instructions
Network Camera For professional use only
Model No. WV-X5550LT Outdoor use WV-X5550LTPJ Outdoor use
WARNING:
· This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
· Operation of this equipment in a residential environment could cause radio
interference.
CAUTION: · The network camera is only intended for a
connection to an Ethernet without routing to the outside plant. · This product
has no power switch. Be sure to install disconnect devices such as a circuit
breaker to shut down the main power of power supplying equipment to this
product.
: Alternating current symbol
· Only connect 24 V AC Class2 power supply (UL 1310/CSA 223) or limited power
source (IEC/EN/UL/ CSA 60950-1 or IEC/EN/UL/CSA 62368-1 Annex Q).
· Before attempting to connect or operate this product, please read these
instructions carefully.
NOTICE:
· This product is not suitable for use in locations where children are likely
to be present.
· Do not install this product in locations where ordinary persons can easily
reach.
· This product is a professional equipment.
· For information about screws and other parts required for installation,
refer to the corresponding section of this document.
·
RISK GROUP2 CAUTION
IR emitted from this product.
Avoid eye exposure.
Use appropriate shielding or eye protection
About the user manuals
Product documentation is composed of the following documents. · Installation
Guide (this document): Provides information about
“Precautions”,”Precautions for installation” and the installation method. ·
Basic Information (in the following website): Provides information about
“Precautions for use” and “Detail specifications”. · Operating Instructions
(in the following website): Explains how to perform the
settings and how to operate this camera. https://i-pro.com/library/vcc/
“<Control No.: C****>” used in these documents should be used to search for
information on our support website
(https://i-pro.com/global/en/surveillance/training_support/support/
technical_information) and will guide you to the right information.
· Before attempting to connect or operate this product, please read these
instructions carefully and save this manual for future use.
· The external appearance and other parts shown in this manual may differ from
the actual product within the scope that will not interfere with normal use
due to improvement of the product.
For U.S. and Canada:
i-PRO Americas Inc. https://www.i-pro.com/
For Europe and other countries:
i-PRO Co., Ltd. Fukuoka, Japan https://www.i-pro.com/
i-PRO EMEA B.V. UK Branch 1010 Cambourne Business Park, Cambridgeshire CB23
6DP
Authorised Representative in EU: i-PRO EMEA B.V. Laarderhoogtweg 25, 1101 EB
Amsterdam, Netherlands
© i-PRO Co., Ltd. 2022
Cs0720-2042 Printed in China
Disposal of Old Equipment and Batteries Only for European Union and countries
with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries must not be mixed
with general household waste. For proper treatment, recovery and recycling of
old products and used batteries, please take them to applicable collection
points in accordance with your national legislation. By disposing of them
correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment. For more information
about collection and recycling, please contact your local authority. Penalties
may be applicable for incorrect disposal of this waste, in accordance with
national legislation. Note for the battery symbol (bottom symbol) This symbol
might be used in combination with a chemical symbol. In this case it complies
with the requirement set by the Directive for the chemical involved.
For U.S.A.
NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
FCC CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Supplier’s Declaration of conformity Trade name : i-PRO Model No. : WV-X5550LT
/ WV-X5550LTPJ Responsible Party : i-PRO Americas Inc. 8550 Fallbrook Drive,
Suite 200 Houston, Texas 77064 Support Contact :
1-800-513-5417
For U.S.A. The model number and serial number of this product may be found on
the surface of the unit. You should note the model number and serial number of
this unit in the space provided and retain this book as a permanent record of
your purchase to aid identification in the event of theft.
Model No. Serial No.
For U.S.A. and Canada This device complies with part 15 of FCC Rules and Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions : (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For Canada CAN ICES-3(A)/NMB-3(A)
Méthode d’installation
Vis de fixation recommandée
La capacité de traction minimale
requise
Monter la caméra vidéo sur le sol, le plafond ou le pôle.
M10 × 55 mm {2-5/32 pouces} / 4el.
1539 N {346 (per 1 pc.)
lbf}
Le présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Pour les États-Unis et le Canada La longueur des vis correspond à la longueur à laquelle les écrous, les rondelles et les rondelles élastiques sont fixés des deux côtés de tôles d’acier de 20 mm {25/32 pouces} d’épaisseur. La longueur des boulons varie en fonction du lieu d’installation.
Precautions
Do not insert any foreign objects. Fire or electrical shock may be caused if
water or any foreign objects, such as metal objects, enter inside the unit.
Turn the power off immediately and contact qualified service personnel for
service. Do not use this product in an inflammable atmosphere. Failure to
observe this may cause an explosion resulting in injury. Avoid installing this
product in the locations where salt damage occurs or corrosive gas is
produced. Otherwise, the mounting portions will deteriorate and injury or
accidents due to a fall of the product may occur. Do not strike or give a
strong shock to this product. Failure to observe this may cause injury or
fire. Do not hang down from this product or use this product as a pedestal.
Failure to observe this may cause injury or accidents. Do not damage the power
cable. Do not damage, fabricate, twist, stretch, bundle, or forcibly bend the
power cable. Do not place heavy objects on it, and keep it away from heat
sources. Use of a damaged power cable may cause electric shock, short circuit,
or fire. Consult the dealer for repair. Do not install this product on a place
that is greatly influenced by wind. Installation on a place where the wind
speed is 60 m/s {approx. 134 mph} or more may cause a fall of the product
resulting in injury or accidents. Do not sprinkle more water, exceeding the
performance limit of waterproof with a high
pressure cleaning machine, etc. Fire or electrical shock may be caused by
immersion. Do not attempt to disassemble or modify this product. Failure to
observe this may cause fire, electric shock or a drop resulting in injury or
accidents. Consult the dealer for the repair or inspections. Do not install or
clean the camera, or touch this product, the power cable or the connected
cables during thunder storms. Failure to observe this may cause electric
shock.
Refer installation work to the dealer. Installation work requires technique
and experience. Failure to observe this may cause fire, electric shock,
injury, or damage to the product. Be sure to consult the dealer. Entrust any
work in high places to qualified service personnel. Installation work requires
technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product. Be sure to consult the dealer. Stop
the operation immediately when something is wrong with this product. When
smoke goes up from the product, the smell of smoke comes from the product, or
the exterior of the product has deteriorated, continued use will cause a fire
or fall of the product resulting in injury, or damage to the product. In this
case, turn the power off immediately and contact qualified service personnel
for service. Select an installation area that can support the total weight.
Selecting an inappropriate installation surface may cause this product to fall
down or topple over, resulting in injury or accidents. Installation work shall
be started after sufficient reinforcement. Periodic inspections shall be
conducted. Rust on the metal parts or screws may cause a fall of the product
resulting in injury or accidents. Consult the dealer for the inspections. The
exclusively designed mount bracket shall be used. Failure to observe this may
cause a drop resulting in injury or accidents. Use the exclusively designed
mount bracket for installation. The screws and bolts must be tightened to the
specified torque. Failure to observe this may cause a drop resulting in injury
or accidents. Install this product in a location high enough to avoid vehicles
and objects from bumping
the product. Failure to observe this may cause injury. Turn the power off when
do wiring of this product. Failure to observe this may cause electric shock.
In addition, short circuit or wrong wiring may cause fire. The measures of
protection against a fall of this product shall be taken. Failure to observe
this may cause a drop resulting in injury or accidents. Be sure to install the
safety wire. Do not install this product in locations subject to continuous or
large vibration. Loosening of mounting screws or bolts may cause a fall of the
product resulting in injury or accidents. Do not install this product in a
place that is easily exposed to oil. Otherwise, the mounting portions may
deteriorate and thus the product may fall down, resulting in injury or
accidents. Correctly perform all wiring. Short circuits in the wiring or
incorrect wiring may cause fire or electrical shock. Do not install beneath
areas where layers of snow could fall. Failure to observe this may cause a
drop resulting in injury or accidents. The measures of protection against
snowfall shall be taken. Weight of snow may cause a fall of the product
resulting in injury or accidents. Protect the product against snowfall by
installing it under eaves. Install the product securely on an installation
area in accordance with the installation
instructions. Failure to observe this may cause injury or accidents. Do not
rub the edges of metal parts with your hand. Failure to observe this may cause
injury. Do not look directly at the light-emitting part of IR LEDs. Failure to
observe this may cause damage to eyesight. Use appropriate shielding or eye
protection. Turn the power off when cleaning this product. Failure to observe
this may cause electric shock.
Always inspect after an earthquake. The mounting portions on the main body may be damaged and a fall may occur. Be sure to consult the dealer. Do not touch the lighting parts on the top part of devices. The lighting parts may become hot. Directly touching these parts may cause burns. Be careful when installing this product. Dropping this product on your foot may cause injury. Do not use this product as a footstool or bench. Failure to observe this may cause injury. Do not install this product in a place where the temperature can get abnormally high. Parts may deteriorate, resulting in fire. Do not apply excessive force. Otherwise, front portion may get damaged, resulting in injury or accidents.
Open Source Software
· This product contains open source software licensed under GPL (GNU General
Public License), LGPL (GNU Lesser General Public License), etc.
· Customers can duplicate, distribute and modify the source code of the
software under license of GPL and/or LGPL. · For details concerning licensing
and source code of open source software, click “Click here for OSS
information”
on the “Support” page of the setup menu of the camera and read the displayed
content. · Please note that we shall not respond to any inquiries regarding
the contents of the source code.
Copyright
Except for open source software licensed under GPL/LGPL and so on,
distributing, copying, disassembling, reverse compiling and reverse
engineering of the software provided with this product are all expressly
prohibited. In addition, exporting any software provided with this product
violating export laws is prohibited.
Trademarks and registered trademarks
· Microsoft, Windows, Windows Media, Internet Explorer, Microsoft Edge, and
ActiveX are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
· Intel and Intel Core are trademarks of Intel Corporation or its subsidiaries
in the U.S. and/or other countries. · Adobe, Acrobat, and Reader are either
registered trademarks or trademarks of Adobe in the United States and/or
other countries. · iPad and iPhone are trademarks of Apple Inc., registered in
the U.S. and other countries. · Android and Google Chrome are trademark of
Google LLC. · Firefox is a trademark of the Mozilla Foundation in the US and
other countries. · The word “QR Code” is a registered trademark of DENSO WAVE
INCORPORATED in Japan and other countries. · All other trademarks identified
herein are the property of their respective owners. Covered by one or more
claims of the HEVC patents listed at patentlist.accessadvance.com.
Precautions for installation
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage
resulting from failures arising out of improper installation or operation
inconsistent with this documentation.
In order to prevent injury, the product must be securely mounted to an
installation area according to Installation Guide.
Installation area for this product Select an appropriate place for the
installation area in your particular environment. · Make sure that the
installation area is strong enough to hold this product, such as a concrete
ceiling.
· Install the camera in the foundation area of the architecture or where sufficient strength is assured.
· Do not mount the product on a plaster board or a wooden section because they are too weak. If the product is unavoidably mounted on such a section, the section shall be sufficiently reinforced.
Do not place this product in the following places.
· Locations where a chemical agent is used.
· Locations subject to moisture or oil smoke such as a plant.
· Locations that have a specific environment that is subject to an inflammable atmosphere or solvents.
· Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated.
· Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases such as from hot springs, volcanic regions, etc.
· Locations where the temperature is not within the specified range.
· Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not designed for on-vehicle use.)
· Locations subject to condensation as the result of severe changes in temperature (In case of installing the product in such locations, the front panel may become foggy or condensation may be caused on the panel.)
· Locations near rubber products (packing, rubber feet, etc.)
Screw tightening
Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively.
About reflection of light from outside or IR light
Depending on the incident angle of external light, a ghost may appear on the screen. In the case of
using the IR light, installation of a camera near a wall may cause reflection of infrared rays resulting in a part of the
screen or the entire screen turning whitish.
· Refer to our support website
Take notice of humidity
Install this product when the humidity is low. If installation is performed when it is raining or in very humid conditions,
the inside may be affected by humidity, causing mist-over inside the front panel.
Protection from lightning
When cables are used outdoors, there is a chance that they may be affected by lightning. In such a case, install a
lightning arrestor close to the camera, and make the length of the network cable between the camera and lightning
arrestor as short as possible to prevent the camera from being affected by lightning.
Grounding connection of the lightning arrestor
With the TILT bracket connected to the earth ground, connect the
ground of the lightning arrestor (locally procured) to the right location
of this unit. Procure locally all the screws used for connecting.
Recommended fixing screws: M3×8 mm {5/16 inches} with spring
washer.
When noise disturbance may happen
Noise may appear in video or audio near a strong electric field from
a TV or radio antenna, motors and transformers, or a strong electric field/magnetic field from a power line (lamp line) of AC100 V or more. Conduct the power distribution work to keep 1 m {3.28 ft} away from
them or conduct the electric conduit work using metal pipes. (Be sure to make ground connection of the metal pipes.)
Cable cover Connection position
Make sure to remove this product if it will no longer be used.
This product has no power switch.
When turning off the power, disconnect the power supply from the 24 V AC power supply.
About the battery
A battery is installed inside the camera. Do not leave the battery exposed in environments of excessive heat as a
result of sunlight or fire.
Equipment classification and power source indication label
Refer to the indication label on the bottom side of this unit for the equipment classification, power source, and other
information.
Troubleshooting
Before requesting service, refer to “Troubleshooting” of Basic Information and
Operating Instructions on the manual website. Then, confirm the trouble.
Specifications For further information, refer to the Basic Information.
· Basic
Power source *1:
AC 24 V (50 Hz/60 Hz)
Power consumption *1:
AC 24 V : 3.8 A /Approx. 68 W
Operating environment Ambient operating temperature: -40 °C to +60 °C {40 °F
to +140 °F}
(Power On range: 20 °C to +60 °C {4 °F to +140 °F}) Ambient operating
humidity: 10 % to 100 % (no condensation)
Storage environment Storage temperature: 30 °C to +60 °C {22 °F to +140 °F} Storage humidity: 10 % to 95 % (no condensation)
Waterproof *2:
IP66 (IEC 60529), Type 4X (UL50E) NEMA 4X compliant
Shock resistance:
IK10 (IEC 62262) (Except for front panels)
Wind resistance:
Up to 40 m/s {approx. 89 mph}
Dimensions:
Ceiling mount: 303 mm {11-15/16 inches} (W), 475 mm {18-11/16 inches} (H), 368 mm {14-1/2 inches} (D) Pole mount: 303 mm {11-15/16 inches} (W), 396 mm {15-19/32 inches} (H), 458 mm {18-1/32 inches} (D) Stationary mount: 303 mm {11-15/16 inches} (W), 440 mm {17-5/16 inches} (H), 368 mm {14-1/2 inches} (D)
Mass:
Main body: Approx. 11.5 kg {25.39 lbs} With TILT bracket: Approx. 16.0 kg {35.32 lbs}
Finish:
Main body: Aluminum die cast, Silver Glass and Polycarbonate resin, Clear Outer fixing screws: Stainless steel (Corrosion-resistant treatment) TILT bracket: Aluminum plate and Aluminum die cast, Silver
1 Refer to our support website
Standard accessories
Installation Guide (this document) ………………….1 pc. Code label1 ………………………………………………1 pc. IMPORTANT SAFETY INSTRUCTIONS…………..1 pc. 1 This label may be required for network management. Use caution not to lose this label.
The following parts are used during installation procedures.
Waterproof tape………………………………………….1 pc. RJ45 waterproof connector cover …………………1 pc.
Safety wire…………………………………………………1 pc. RJ45 waterproof connector cap ……………………1 pc.
24 V AC power supply connector kit……………… 1 set (Power supply connector
housing: 1 pc.,
Contact: 3 pcs.)
Hexagon screw (M10 × 20 mm) {25/32 inches} …………………….. 6 pcs. (of them, 1 for spare)
Cable cover ……………………………………………….1 pc. Bit (Hex wrench, screw size 6.35 mm {1/4 inches} T20) ……………………….1 pc.
Other items that are needed (not included)
1Wi -Fi USB adapter (locally procured)
Be sure to use a Wi-Fi USB adapter that is checked its operability. Refer to
our support website
2M10 bolts and nuts with washers and spring washers (4 sets) (locally
procured)
Installation method
Recommended screw*1
Minimum pull-out strength*2
Mount the camera onto the floor, ceiling or pole.
M10 x 55 mm {2-5/32 inches}*3 / 4 pcs.
1539 N {346 lbf} (per 1 pc.)
1 Select screws according to the material of the location that the camera will be mounted to. In this case, wood screws and nails should not be used.
2 For information about the minimum pull-out strength, refer to our support website
sides of 20 mm {25/32 inches} thick steel sheets. The length of bolts differs
depending on the installation location.
Parts and functions
· A part of the cable cover is omitted in the following illustrations.
TILT bracket
IR LED Light
Front panel Cable cover hook
Name plate
RJ45 Network cable Power supply terminal (24 V AC)
USB cover
RISK GROUP2 CAUTION IR emitted from this product. Avoid eye exposure. Use
appropriate shielding or eye protection
Installations
{1} Limitations for the installation location
Please meet the following conditions for the camera installation.
Installation inclination: 7° 10°
Road surface
Height: 4.5 m {14.8 ft} 5.8 m {19.0 ft}
Distance: 21 m {69 ft} 26 m {85 ft}
Installation oscillation angle 0°±13°
Road surface
Road width R 7.0 m {23.0 ft} 0 m L 7.0 m {23.0 ft}
{3} Preparations (Continued)
Set the “User name” and “Password” for the camera. Before installing the
camera, make sure to connect to a PC to the camera and set the camera’s “User
name” and “Password” in advance. If necessary, also set the IP address.
1Connect a PC to the camera and connect power to the camera.
2Download the IP Setting Software on your PC and connect to the network by following information described on our support website <Control No.: 0123>.
3The “User name” and “Password” set when first connecting to the camera are used in step {8} when connecting to the camera with a tablet or other device. Make sure to manage them and report them to the administrator.
- On the PC screen, 2 screens for the vicinities around the driver’s seat and number plate are displayed.
{4} Work on the installation surface
1Preparing the installation surface
The installation surface for the TILT bracket of the camera is shown on the
illustration to the right. Open 4 holes for securing M10 screws at 142 mm
{5-19/32 inches} × 142 mm {5-19/32 inches} positions, and open a ø11 mm {7/16
inches} hole so that the PAN rotation is centered. Also, check if there are
any uneven areas on the installation surface and if there are any obstructions
in the rotating range of the TILT bracket.
Ceiling mount TOP view
272 mm {10-23/32 inches} 142 mm {5-19/32 inches}
230 mm {9-1/16 inches}
ø360 mm {ø14-3/16 inches}
142 mm {5-19/32 inches}
IMPORTANT:
In this Installation Guide, attaching the product to a ceiling surface is explained.
2Temporarily fix the TILT bracket to the installation surface with M10 Bolts
and nuts with washers and spring washers (4 sets, locally procured)
Recommended tightening torque: 10.8 N·m {8.0 lbf·ft}
Note:
· Select attaching screws, bolt nuts, anchors, and other parts according to
the installation surface and installation method.
M10 Bolt and nut (4 pcs.) (locally procured)
Ceiling
Ceiling
{2} Installation method
· A part of the cable cover is omitted in the following illustrations.
There are 3 methods to install the camera as follows. Select an installation method in accordance with the conditions of the installation location.
17 mm {21/32 inches}
TILT bracket
{5} Temporally attach the camera to the TILT bracket
Ceiling mount
Pole mount
Stationary mount
{3} Preparations
Remove the hexagon screws (M10) (2 pcs.), slide the TILT bracket backwards and
then remove it.
TILT bracket
Remove the protection sheets (both sides) from the TILT bracket.
Bracket sliding direction
Hexagon screw (M10) (2 pcs.)
Protection sheets (both side)
Protection sheets (both side)
Note: · The removed screws are used with the supplied screws in step {5}. Make sure to keep them.
Turn the product on its side and remove the protective covers from the cable and other parts on the bottom side.
Camera sliding direction
Hexagon screw (M10 × 20 mm {25/32 inches}) (6 pcs.) (accessory and removed in
step {3}) Note: · As a temporary adjustment, roughly match the PAN and TILT
and face the camera in the direction that you want to view images.
{6} Fix the safety wire
Safety wire (accessory)
Hexagon screw (M10 × 20 mm {25/32 inches}) (accessory)
Recommended tightening torque: 10.8 N·m {8.0 lbf·ft}
IMPORTANT:
· Attach the safety wire to an area that can support a weight of 100 kg (220
lbs).
· Adjust the fixing position and the number of turns so that the safety wire
does not sag.
{7} Connecting wires
IMPORTANT: · Device to which power can be supplied to this product is a power
source with 24 V AC output and
less than 250 VA apparent power (capacitance). · Turn off each system’s power
supply before making a connection.
Connect an Ethernet cable (category 5e or better, straight) to RJ45 network cable.
(a) RJ45 plug (locally procured)
(a)
(b)
(c) (d)
Use an industrial tool (locally procured) to crimp the Ethernet
cable (locally procured).
Wire and crimp
(b) RJ45 waterproof connector cover (accessory)
(c) RJ45 waterproof connector cap (accessory)
(d) Ethernet cable (locally procured)
Insert the RJ45 plug
IMPORTANT:
· Do not install the camera where the RJ45 waterproof connector is exposed to
constant rain or moisture.
· When removing the RJ45 waterproof connector, be sure to disconnect it in the
reverse order of the procedure on the right figure.
Align the “” with the “” and turn it to the “”.
Tighten until the gap disappears
Assemble 24 V AC connector kit (accessory) and connect it to the power cable
of camera body.
1Recommended wire rod and array of pins of connector housing (accessory)
AWG size (stranded wire) #22 (0.33 mm2)
20 (0.52 mm2)
18 (0.83 mm2)
Wire length
7 m {23.0 ft}
14 m {45.9 ft}
20 m {65.6 ft}
Power supply connector housing
Pin No.
Signal
1
24 V AC LIVE (Brown)
2
24 V AC NEUTRAL (Blue)
3
Ground (Black)
4
Not use
2How to assemble the 24 V AC power supply connector kit
· Remove approx. 3 mm {1/8 inches} of the outer jacket of the cable and twist
the cable core to prevent the short circuit first.
· Insert the tip of the cable into the point A of the contact (accessory), and
hold the cable using the cable clamp.
Approx. 3 mm {1/8 inches} Cable
Upper A
Insert Contact (accessory)
· Procure either of the following tools for clamping. Molex manual clamp tool:
57027-5000 (For UL1015), 57026-5000 (For UL1007)
· After clamping the contact and the cable, insert the contact properly into
the power supply connector housing.
Upper
Cable
Contact (accessory) Power supply connector housing (accessory)
3Adequate waterproof treatment is required for the 24 V AC power cable when
installing the camera with cables exposed.
· Apply some waterproof tapes (accessory) as shown in the right.
· Stretch the tape to approx. twice its length and wind it around the cable.
Insufficiently stretching the tape may cause inadequate waterproofing.
Approx. 20 mm {25/32 inches}
Approx. 20 mm {25/32 inches}
{8} Attach the cable cover to the camera
Note: · In case of stationary mount, it is no need to
attach this cable cover.
Cable cover hook
Cable cover
Recommended tightening torque: 10.8 N·m {8.0 lbf·ft}
Cable cover fixing screw
{9} Preparation for adjustment
1Loosen two locking screws of USB cover using the bit (accessory) and pull the
USB cover toward you.
2Insert the Wi-Fi USB adapter (locally procured) to the USB terminal (for
installation constructor) and then turn on the power of the camera. (The Wi-Fi
USB adapter is used only at the time of the installation/servicing.)
USB terminal (for installation constructor)
USB cover
INITIAL SET button
Wi-Fi USB adapter
3Select “Wi-Fi” from the setting of a tablet or smart phone and then connect
with the Wi-Fi USB adapter (to be locally procured) attached to the camera.
Refer to the manual of the Wi-Fi USB adapter and device in use for how to
connect them. SSID : “Product No.Serial No. of the camera” Password : “cam”
- “Serial No. of the camera”
4Launch the browser on a tablet or smart phone and then enter the following URL to connect with the camera main unit. http://192.168.12.10
Note: If access to http://192.168.12.10 fails, try http://10.0.0.10.
5An authentication window is displayed on the screen.
Enter the “User name” and “Password” set in step {3}.
6Remove the protection film in regards to the front panel of the camera.
{9} Adjustment
As an example, the explanation is provided using a Wi-Fi USB adapter. When
adjusting using a directly connected PC. Refer to “Easy Installation” of the
operating Instructions on the manual website.
Step1 Enter the relation between the subject and the camera position.
1Before entering the installation information, measure the distance between
the camera and the target object.
2From the initial screen on the right, tap the ” ” and ” ” buttons to enter
values.
(a) Height: height from the road surface (4.5 m {14.8 ft} to 5.8 m {19.0 ft})
(b) Distance: distance from the subject (21 m {69 ft} to 26 m {85 ft})
(c) Deflection Distance: distance from traffic lane of the road (R 7.0 m {23.0
ft} 0 m L 7.0 m {23.0 ft})
3Tap [Next] at the bottom of the screen.
(a) (b)
(c)
Initial screen
Step2 When [Next] is tapped, the ideal zoom, focus, and inclination filter restrictions for the camera are adjusted and the live setting screen is displayed.
Note: If the live screen is not displayed, reload the browser.
M10 Bolt and nut (4 pcs.) Installation surface
1Adjust the direction of the camera to match
the camera rotated in the PAN and TILT directions. (If it is difficult to
adjust, press [-] of [Zoom], and then press [Reset] after adjusting the PAN
and TILT.)
2Use [+] and [-] of [Zoom] to adjust the angle
of view. (Adjust so that the driver’s seat is in the center of the screen.)
3If necessary, use [ ] and [ ] of [Focus] to adjust the focus.
4Tighten the M10 Bolts and nuts (4 pcs.) and fix the PAN direction.
Recommended tightening torque: 10.8 N·m {8.0 lbf·ft}
5Tighten the hexagon screws (M10 × 20 mm {25/32 inches}) (6 pcs.) and fix the
TILT
direction.
Hexagon screw (M10 × 20 mm {25/32 inches}) (6 pcs.)
Recommended tightening torque: 10.8 N·m {8.0 lbf·ft}
6Once the adjustments are completed, tap [Next] at the bottom of the screen.
2
3
6
Focus adjustment
Step3 Finish operations
Note: For information on detailed adjustment methods, refer to Operating
Instructions on the manual website.
1Remove the Wi-Fi USB adapter. (In the case of using a Wi-Fi USB adapter)
2Attach the USB cover and fix it by tighten the USB cover fixing screws (2
places) using the bit (accessory). Recommended tightening torque: 0.75 N·m
{0.55 lbf·ft}
1
3Connect the camera to a network by following “Configure the network settings”
on our support website
4Close the browser.
Note:
2
· Check if the focus, brightness, etc. needs to be adjusted on the PC screen before starting operations.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>