DOMETIC FW 3000 Under Bench Air Conditioner User Manual

FW 3000 Under Bench Air Conditioner
User Manual FW 3000
Under-bench air conditioner
Operating manual

FW 3000 Under Bench Air Conditioner

© 2023 Dometic Group. The visual appearance of the contents of this manual is protected by copyright and design law. The underlying technical design and the products contained herein may be protected by design, patent or be patent pending. The trademarks mentioned in this manual belong to Dometic Sweden AB. All rights are reserved. ![DOMETIC FW 3000 Under Bench Air Conditioner

• fig 2](https://manuals.plus/wp-content/uploads/2023/08/DOMETIC-FW-3000 -Under-Bench-Air-Conditioner-fig-2.jpg)

Original instructions
Please read these instructions carefully and follow all instructions, guidelines, and warnings included in this product manual in order to ensure that you install, use, and maintain the product properly at all times. These instructions MUST stay with this product.
By using the product, you hereby confirm that you have read all instructions, guidelines, and warnings carefully and that you understand and agree to abide by the terms and conditions as set forth herein. You agree to use this product only for the intended purpose and application and in accordance with the instructions, guidelines, and warnings as set forth in this product manual as well as in accordance with all applicable laws and regulations. A failure to read and follow the instructions and warnings set forth  herein may result in an injury to yourself and others, damage to your product or damage to other property in the vicinity.
This product manual, including the instructions, guidelines, and warnings, and related documentation, may be subject to changes and updates. For up-to-date product information, please visit documents.dometic.com.
Find the installation manual online on documents.dometic.com/?object_id=51383

Explanation of symbols

WARNING!
Safety instruction: Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION!
Safety instruction: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTICE!
Indicates a situation that, if not avoided, can result in property damage.
NOTE
Supplementary information for operating the product.

Safety instructions

Note the following basic safety information when using electrical devices to protect against:

• Electric shock
• Fire hazards
• Injury

2.1 General safety
WARNING!

• This device can be used by children aged 8 years or over, as well as by persons with diminished physical, sensory or mental capacities or a lack of experience and/or knowledge, providing they are supervised or have been taught how to use the device safely and are aware of the resulting risks.
• Cleaning and user maintenance must not be carried out by children without supervision.
• Children must not play with the device.
• Children must be supervised to ensure that they do not play with the device.
• Always keep and use the device out of the reach of children under the age of 8 years.
• Only use the device as intended.
• Do not make any alterations or conversions to the device.
• Installation, maintenance and repairs of the under-bench air conditioner must only be carried out by qualified personnel who are familiar with the risks involved when handling refrigerant and air conditioning systems as well as the relevant regulations. Inadequate repairs may cause serious hazards. For repair service, please contact the service center in your country (addresses on the back page).
• Do not use the under-bench air conditioner near flammable fluids.
• Ensure no combustible objects are stored or installed near the air outlet. A distance of at least 50 cm must be kept.
• Do not reach into air outlets or insert any foreign objects in the underbench air conditioner.
• Do not undo the upper cover of the under-bench air conditioner in the event of a fire. Use approved extinguishing agents instead. Do not use water to  xtinguish fires.
• A damaged supply cord must be replaced by the manufacturer or a qualified person in order to avoid a hazard.

NOTICE!

• If faults occur in the under-bench air conditioner’s refrigerant circuit, the under-bench air conditioner must be checked by a specialist company and properly repaired. The refrigerant must never be released into the air.
• Do not apply heavy objects or pressure on the device.

2.2 Operating the device safely
WARNING!

• Always disconnect the power supply when working on the device.

CAUTION!

• Do not touch the device during operation. The device contains hot and cold components, moving parts and electrical items which may cause injury.

NOTICE!

• The under-bench air conditioner is not suitable for use in agricultural or construction vehicles.
• Operate the device only if you are certain that the housing and the cables are undamaged.

Target group for this manual

This operating manual is for the user of the under-bench air conditioner.

Scope of delivery

• Dometic FreshWell under-bench air conditioner
• Operating manual

Intended use

The Dometic FreshWell3000 under-bench air conditioner is designed for use in motor caravans, caravans and other vehicles with habitation compartments only. It is not suitable for houses and apartments.
The under-bench air conditioner is not suitable for installation in construction machines, agricultural machines or similar equipment. It will not work properly if exposed to strong vibrations.
The operating mode of FreshWell3000 is guaranteed for temperatures between 0°C and 52°C.
This product is only suitable for the intended purpose and application in accordance with these instructions.
This manual provides information that is necessary for proper installation and/or operation of the product. Poor installation and/or improper operating or maintenance will result in unsatisfactory performance and a possible failure.
The manufacturer accepts no liability for any injury or damage to the product resulting from:

• Incorrect assembly or connection, including excess voltage
• Incorrect maintenance or use of spare parts other than original spare parts provided by the manufacturer
• Alterations to the product without express permission from the manufacturer
• Use for purposes other than those described in this manual

Dometic reserves the right to change product appearance and product specifications.
In particular, the manufacturer will not be liable for any consequential damage, especially consequential damage caused by failure of the under-bench air conditioner.

Technical description

The under-bench air conditioner supplies the interior with cool dehumidified air without dust and dirt.
The under-bench air conditioner is operated with the remote control.
NOTE
The under-bench air conditioner can lower the temperature within the vehicle to a certain level. The temperature depends on the type of vehicle, the ambient temperature and the cooling capacity of your under-bench air conditioner.
Below an outer temperature of 16 °C the under-bench air conditioner doesn’t cool anymore. In this case only use the air conditioning mode “Circulating air” ( ).
6.1 Components
The refrigerant circuit of the under-bench air conditioner consists of the following main components (fig.1, page 3):

• Compressor (1)
  The compressor draws in the refrigerant used and compresses it. This raises the pressure and therefore the temperature of the refrigerant.

• Condenser (2)
  The built-in liquefier works like a cooler or heat exchanger. The air flowing past absorbs the heat and the hot refrigerant gas cools down and becomes liquid.

• Evaporator (3)
  The evaporators cool down and dehumidify the air flowing past them. The refrigerant absorbs the heat and vaporises.

• Blower (4)
  A blower distributes the cooled or heated air within the vehicle through an air outlet unit.

• 4-way valve (5)
  The 4-way valve reverses the cooling circuit. Thus the internal register of the evaporator becomes a condenser and heats the air passing through.

• Electric heating element (6)
  The electric heating element increases the heating effect when the outer temperature is low.

• Air inlet (7), air outlet (8) for external heat exchanger
  Air is sucked into the device through the air inlet and escapes through the air outlet.

• Air inlet (9), air outlet (10) for internal heat exchanger
  Air is sucked into the device through the air inlet and escapes through the air outlet. The internal heat exchanger treats the air in order to be cold or hot depending on active mode.

6.2 Receiver
The receiver (fig.2, page 3) contains the following control and display elements:

No| Explanation|
---|---|---
1| Digital display| Displays the room temperature.
2| Red/green LED| Constantly lit, red: the stand-by mode is active
Constantly lit, green: any other mode is active
Flashing, red/green: the under-bench air conditioner is on, but the supply voltage is not present
3| Blue LED| Constantly lit: the cooling mode is active
Flashing: the dehumidification mode is active
Off: any other mode is active
4| Orange LED| Constantly lit: the heating mode is active Flashing: the heating mode is active, but the air conditioner is not yet producing hot air, because the defrost function or the preventing cold air function is active The defrost function prevents ice on the external battery
exchanger while in heating mode.
The preventing cold air function prevents that cold air is blown into the vehicle while in heating mode.
Off: any other mode is active
5| Yellow LED| Constantly lit: the timer mode is active
Off: the timer mode is not active

In case of an alarm the display shows an error code to identify the fault:

6.3 Remote control
All settings of the device (e. g. temperature settings, timer programming) are transmitted to the under-bench air conditioner by remote control.
The following control and display elements are available on the remote control (fig.3, page 4) :

Displays the following:
• Time
• Selected room temperature (target value) in °C or °F
• Actual room temperature
• Air conditioning mode
• Blower level
• Symbols for active additional functions
• Battery status
2| button:
Switches the air conditioner and remote control on or to stand-by mode
3| button:
Selects the blower setting
4| MODE button:
Selects the air conditioning mode
5| button:
Activates the sleep function. The sleep function automatically modifies the target
value to provide a pleasant sleeping temperature.
6| button:
Press once: Displays the current interior temperature (symbol is displayed).
Press again: Displays the set temperature.
7| button:
No function assigned yet
8| °C/°F button:
Switches between temperature units Celsius (°C) and Fahrenheit (°F).
9| button:
Sets the timer and the clock.
10| SET button:
Confirms and saves settings.
11| button:
No function assigned yet
12| + button:
Increases the value
13| – button:
Reduces the value
14| Symbol (batteries empty)
Is displayed when the batteries in the remote control are empty. If this happens, replace the batteries, see chapter “Replacing the remote control batteries” on page 23.
15| Symbol (transmitting values)
Is displayed briefly when the remote control is transmitting values to the underbench air conditioner.

6.4 Air conditioning modes
The under-bench air conditioner has the following air conditioning modes:

point) automatically and manages the compressor,
heat pump and fan speed by comparing the set point with the room temperature and it sets the corresponding conditioning mode (see following table).
The , + and – buttons are deactivated in this mode.
Cooling| | You specify the temperature and blower settings, and  the air conditioner cools the interior to this temperature.
Heating| | You specify the temperature and blower settings, and the air conditioner heats the interior to this temperature.
Circulating air| | You specify the blower level, and the air conditioner blows air into the interior.
Dehumidification| | You specify the temperature, and the air conditioner cools the interior to this temperature and controls the
necessary blower output and dehumidify the interior (Circulating air mode).
The button is deactivated in this mode.
Current room temperature 9| 9 < 20 °C| 22 °C < 9 < 25 °C| 9 _?. 25 °C
---|---|---|---
Set point:| 20 °C| 22 °C| 25 °C
Conditioning mode:| Heating or
Circulating air| Dehumidification or
Circulating air| Cooling

6.5 Additional functions
The under-bench air conditioner has the following additional functions:

°C after two hours to generate a pleasant temperature for sleeping.

Before initial use

Inspection before starting up
Before switching on the under-bench air conditioner, observe the following:
➤ Check whether the supply voltage and frequency correspond to the values specified in the technical data, see page 30.
➤ Ensure both the air intake opening and the air nozzles are free. All ventilation grilles must always be kept free to ensure that the under-bench air conditioner is able to operate at maximum capacity.
CAUTION! Risk of injury
Do not insert your fingers or objects into the air nozzles or the intake grille.
Setting the time
➤ Set the current time: see chapter “Setting the time” on page 24.
Set the remote control
➤ Insert the batteries (see chapter “Replacing the remote control batteries” on page 23).
✔ The display shows all symbols for 5 seconds.
➤ Press simultaneously the button and the button during this 5 seconds.
✔ The display shows the default model number.
➤ Press simultaneously + and – button within 3 seconds to select the model number:
– FreshWell3000: 02
–FreshJet: 07
–FreshLight: 11
✔ The display shows all symbols for 5 seconds.
✔ The remote control is ready for operation.

Operating the under-bench air conditioner

8.1 Basic notes on operation
The under-bench air conditioner has three operating modes:

switched on with the remote control.
On| The under-bench air conditioner is conditioning the air in the interior.

The receiver switches on when it receives pulses from the remote control. The display shows (flashing) the temperature setting, after 10 seconds the display shows the room temperature, then it switches off.
Use the remote control to

• switch the under-bench air conditioner to and from stand-by mode.
• adjust the settings.
• select additional functions.

8.2 Using the remote control
The remote control must be pointed at the IR receiver (fig.2 4, page 3) on the receiver during operation.
When a button is pressed, the value is transmitted directly to the under-bench air conditioner. The under-bench air conditioner confirms the receipt of data with a high note.
Switching only the remote control to or from stand-by
In stand-by mode, the remote control display shows only the time.
If the remote control is not pointing to the IR receiver (fig.2 4, page 3) on the control panel, you can activate the remote control or switch it to stand- by independently from the under-bench air conditioner:
➤ Press the button.

8.3 Hint for improved use
The following hints will optimize the performance of the under-bench air conditioner:

• Improve the heat insulation of your vehicle by sealing gaps and hanging reflective blinds or curtains on your windows.
• If the vehicle has been subjected to direct sunlight for a long time: Operate the under-bench air conditioner in the “Circulating air” ( ) mode with the windows open for a while before switching on the “Cooling” ( ) air conditioning mode.
• Avoid opening doors and windows as far as possible in the “Cooling” ( ) mode.
• Select an appropriate temperature and blower speed.
• Align the air nozzles sensibly.
• Ensure the air nozzles and intake grille are not covered by cloths, paper or other objects.
• Clean the air filter periodically.

8.4 Switching the under-bench air conditioner on and off
NOTE

• When the under-bench air conditioner is switched on, the device begins to condition the air to the values that were set most recently.
• Use the remote control to switch the under-bench air conditioner to and from stand-by mode. Press the button.
• Operate the under-bench by remote control and via LIN bus. If you use LIN bus control the receiver is not required.
• Do not use the under-bench air conditioner if the vehicle is tilted more than 10°.

When you switch on the under-bench air conditioner, the device waits a few minutes before operating the compressor.
8.5 Selecting the air conditioning mode
NOTE
The under-bench air conditioner must be switched on.
➤ Select the desired air conditioning mode using the MODE key, see chapter “Air conditioning modes” on page 15.
✔ The under-bench air conditioner confirms the receipt of the values with a high note.
✔ The under-bench air conditioner is switched to the selected air conditioning mode.
8.6 Selecting the blower setting manually
NOTE
The under-bench air conditioner must be switched on.
The blower controls the strength of the air supply.
In the “Cooling” ( ) and “Circulating air” ( ) modes, the blower levels can be selected manually. In the other air conditioning modes, the under-bench air conditioner controls the blower level automatically.

not available in the “Cooling” ( ) mode
| Automatic mode, only available in the “Cooling” ( ), “Heating” (  ) and “Dehumidifying” ( ) modes.

➤ Use the button to select the desired blower level.
✔ The under-bench air conditioner confirms the receipt of the values with a high note.
✔ The new blower level has been set.
8.7 Setting the temperature
NOTE
The under-bench air conditioner must be switched on.
Cooling Mode
In the “Cooling” ( ), and “Dehumidifying” ( ) modes, a temperature between 16 °C and 31 °C can be set via the remote control.
➤ Use the + or – button to select the desired temperature.
✔ The under-bench air conditioner confirms the receipt of the values with a high note.
✔ The temperature is set on the under-bench air conditioner.
Heating Mode
In the “Heating” ( ) mode, a temperature between 16 °C and 31 °C can be set via the remote control.
➤ Use the + or – button to select the desired temperature.
✔ The under-bench air conditioner confirms the receipt of the values with a high note.
✔ The temperature is set on the under-bench air conditioner.
8.8 Setting the timer
The timer function allows ou to set a specific time period for air conditioning. The switch-on time, the switch-off time or both values can be specified.
NOTE
The remote control returns to its initial mode if no button is pressed on the remote control for 15 seconds while programming the timer.
➤ Before programming the timer, select the air conditioning mode and all required values (e.g. temperature).
Setting the switch-on time
NOTE
The under-bench air conditioner must be switched off.
➤ Press the button once.
✔ The ON symbol ( ) flashes on the display of the remote control.
➤ Use the + or – button to set the time when the under-bench air conditioner is to switch on.
➤ Press the SET button to transmit the value to the under-bench air conditioner.
✔ The switch-on time is set on the under-bench air conditioner.
The under-bench air conditioner is switched on with the selected air conditioning mode at the specified time.
➤ Switch the under-bench air conditioner to stand-by.
Setting the switch-off time
NOTE
The under-bench air conditioner must be switched on.
➤ Press the button twice.
✔ The OFF symbol ( ) flashes on the display of the remote control.
➤ Use the + or – button to set the time when the under-bench air conditioner is to switch off.
➤ Press the SET button to transmit the value to the under-bench air conditioner.
✔ The switch-off time is set on the under-bench air conditioner.
The under-bench air conditioner runs in the selected air conditioning mode until the specified time.

Setting the switch-on and switch-off times
➤ Press the button three times.
✔ The ON symbol ( ) flashes on the display of the remote control.
The OFF symbol ( ) is displayed.
➤ Use the + or – button to set the time when the under-bench air conditioner is to switch on.
➤ Press the button again.
✔ The OFF symbol ( ) flashes on the display of the remote control.
➤ Use the + or – button to set the time when the under-bench air conditioner is to switch off.
➤ Press the SET button to transmit the value to the under-bench air conditioner.
✔ The switch-on and switch-off times are set on the under-bench air conditioner.
The under-bench air conditioner starts in the selected air conditioning mode at the specified time and runs until the second specified time.
➤ Switch the under-bench air conditioner to stand-by.
Canceling timer settings
If the timer has been set, these settings can be canceled as follows:
➤ Press the button four times.
✔ The timer symbol disappears.
✔ The setting has been canceled.
8.9 Activating the Sleep function
NOTE
The sleep function is deactivated in “Circulating air” ( ) and the
“Dehumidifying” ( ) modes.
When the sleep function is activated, the set temperature is modified by 1 °C after one hour and by 2 °C after two hours to ensure a pleasant temperature for sleeping.
➤ Set the required temperature (see chapter “Setting the temperature” on page 20).
➤ Press the button.
✔ The symbol appears in the display.
The sleep function is activated.
➤ To deactivate the sleep function press the button again.
NOTE
The sleep function is deactivated if the MODE button is pressed.
8.10 Replacing the remote control batteries
Replace the batteries if you see the symbol on the display.
The battery compartment is on the back of the remote control.
➤ Gently push down the lid of the battery compartment and slide it open in the direction of the arrow.
➤ Insert the new batteries (2x type AAA) in the remote control as indicated in the battery compartment.
➤ Close the cover of the battery compartment.
8.11 Setting the time
The remote control needs the current time in order to program the timer. The time is indicated on the display of the remote control.
Perform the following steps to set the time:
NOTE
The remote control returns to its initial mode and saves the current setting, if no key is pressed on the remote control for 15 seconds while setting the time.
➤ Press and hold the button in order to get into the mode for setting the time.
✔ The time flashes on the display of the remote control.
➤ Use the + or – button to set the current time.
Press the + or – button longer than 2 s to increase or decrease the time quicker.
➤ Press the SET button to confirm the time.

Cleaning the under-bench air conditioner

NOTICE! Damage hazard

• Do not clean the under-bench air conditioner with a high-pressure cleaner. Exposure to water can damage the air conditioner.
• Do not use sharp or hard objects or cleaning agents for cleaning as these may damage the under-bench air conditioner.
• To clean the under-bench air conditioner, use water with a gentle cleaning agent. Never use petrol, diesel or solvents.

➤ Clean the housing of the under-bench air conditioner and the air outlet unit occasionally with a damp cloth.
➤ Regularly remove leaves and other dirt from the ventilation grilles (fig.4 1, page 4) of the under-bench air conditioner. Make sure you do not damage the grilles in the process.
➤ Clean the remote control with a slightly damp cloth from time to time. We recommend using a cleaning cloth for glasses to clean the display.

Maintenance of the under-bench air conditioner

WARNING! Risk of injury
Any other maintenance work to that which is described here may only be carried out by qualified personnel who are familiar with the risks involved when handling refrigerant and air conditioning systems as well as the relevant regulations.

➤ Check whether the condensation water drainage channels (fig.4 2, page 4) at the sides of the under-bench air conditioner are clear and the condensation water is able to escape.
Regularly| Clean the filter of the air discharge unit (fig.5, page 5):
➤ Pull the filter (1) out of the fastening.
➤ Clean the filter (1) with a detergent solution and let it dry.
➤ Put the dry filter (1) back in.
Once per year| Have the heat exchanger serviced:
➤ Have the heat exchanger of the under-bench air conditioner serviced by specialist workshop.
Once per year| Replace the carbon filter (fig.5, page 5) (optional):
➤ Pull the filter (1) out of the fastening.
➤ Remove the carbon filter (2).
➤ Put a new carbon filter in.
or
➤ Clean the filter (1) with a detergent solution and let it dry.
➤ Put the dry filter (1) back in.

Troubleshooting

Set the under-bench air conditioner to cooling.
The under-bench air conditioner is not set to cooling.| The under-bench air conditioner is only designed for ambient temperatures of up to 52 °C.
The temperature set is higher than the room temperature.| ➤ Select a lower temperature.
The ambient temperature is below 16 °C.| The under-bench air conditioner is only designed for ambient temperatures above 16 °C.
The thermal protection is defective.| ➤ Contact an authorized service agent.
The compressor is damaged.
The refrigerating agent filling is insufficient.
The heat exchange coils are polluted.
The external blower is defective.
No heating capacity| The under-bench air conditioner is not set to heating.| ➤ Set the under-bench air conditioner to heating.
The ambient temperature is below 0°C.| The under-bench air conditioner is only designed for ambient temperatures higher than 0 °C.
The temperature set is lower than the room temperature.| ➤ Select a higher temperature.
The ambient temperature is higher than 31 °C.| The temperature is adjustable between 16 °C and 31 °C.
The thermal protection is defective.| ➤ Contact an authorized service agent.
The compressor is damaged.
The refrigerating agent filling is insufficient.
The heat exchange coils are polluted.
The external blower is defective.
Low air output| The air filter is obstructed.| ➤ Clean the air filter.
The heat exchange coils are polluted.| ➤ Contact an authorized service agent.
The internal blower is defective.
Water enters the  vehicle| The condensation water drainage  openings are clogged up.| ➤ Clean the drainage openings  for condensation water.
The seals are damaged.| ➤ Contact an authorized service agent.
The underbench air conditioner does not  switch on.| No supply voltage (230 Vw) connected.| ➤ Check the power supply.
The voltage is too low (under200 Vw).
The voltage converter is defective.
The defective thermal protection is defective.
The electrical fuse of the power supply is too low.| ➤ Contact an authorized service agent.
Under-bench air conditioner stops working.| The air filter is obstructed.| ➤ Clean the air filter.
The voltage is too low (under 200 Vw). The voltage converter is defective.| ➤ Contact an authorized service agent.
The defective thermal protection is defective.
The condenser fan is damaged.
The heat exchange coils are polluted.
The external blower is defective.
The underbench air conditioner does not  switch off.| One of the temperature sensors is defective.| ➤ Contact an authorized service agent.

Warranty

The statutory warranty period applies. If the product is defective, please contact the service partner in your country (addresses on the back on the instruction manual).
Our experts will be happy to help you and will discuss the warranty process with you in more detail.

Disposal

Regulations for environmental safety and correct disposal
All organizations must apply a set of procedures to identify, evaluate and control the influence that their activities (manufacturing, products, services, etc.) have on the environment.
The procedures to be followed to identify significant environmental impact must take the following factors into account:

• use of raw materials and natural resources
• atmospheric emissions
• discharge of liquids
• waste management and recycling
• contamination of the soil

In order to minimize environmental impact, the manufacturer provides a series of indications here below that should be taken into account by all those who, for whatever reason, interact with the appliance during its working life.

• All packing components must be disposed of (preferably recycled) in compliance with statutory legislation in the country in which disposal takes place.
• All product components must be disposed of (preferably recycled) in compliance with statutory legislation in the country in which disposal takes place.
• For correct disposal, the appliance must be consigned to an authorized waste disposal company to ensure that all recyclable components are reused and the remaining materials are processed properly.
• During installation ensure the room has adequate ventilation to prevent the buildup of stale air that might be harmful to the health of the operators.
• During operation and maintenance ensure that any waste pollutant products (oil, grease, etc.) are disposed of correctly.
• Keep noise levels down to reduce noise pollution.

For more information on correct dismantling of our products please refer to the recycling handbooks at dometic.com.

Recycling products with non-replaceable batteries, rechargeable batteries or light sources
➤ If the product contains any non-replaceable batteries, rechargeable batteries or light sources, you don’t have to remove them before disposal.
➤ If you wish to finally dispose of the product, ask your local recycling center or specialist dealer for details about how to do this in accordance with the applicable disposal regulations.
➤ The product can be disposed free of charge.
Recycling packaging material
****  ➤ Place the packaging material in the appropriate recycling waste bins wherever possible.

Technical data

FreshWel13000

Cooling capacity:| 2700 W
Heating capacity:| 3000 W
(2500W + 500W additional
heating element)
Rated input voltage:| 230 Vim- , 50/60 Hz
Current consumption:| Cooling: 4.3 A
Heating: 4.8 A
Required fuse:| 5 A
Operating temperature range:| 0 °C to +52 °C
Noise emission:| < 70 dB
Refrigerant:| R-410A
Refrigerant quantity:| 0.6 kg
CO2 equivalent:| 1.2528 t
Global warming potential (GWP):| 2088
Additional heating element:| 500 W
Blower:| 3 blower levels
1 automatic mode
Protection class:| IP X5
Max. volume of space in the vehicle (with insulated walls):| 30 m3
Dimensions LxWx H:| fig. 6 page 5
Weight:| approx. 21 kg
Inspection/certification:| ****

This product contains fluorinated greenhouse gases.
The cooling unit is hermetically sealed.

dometic.com

offices](http://dometic.com/sales-offices)

A complete list of Dometic companies, which comprise the Dometic Group, can be found in the public filings of:
DOMETIC GROUP AB Hemvarnsgatan 15 SE-17154 Solna Sweden
4445101821 ST0192 8250201-96 2

References

• Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>