SALUS CONTROLS HTR-RF Smart Home Dial Thermostat User Guide

: June 12, 2024
: SALUS CONTROLS

Table of Contents

Introduction
Product Compliance
Box content
Overlay Information
LED Indication
Installation
Pair (online)
Dial Function
Pair (offline)
Identify (online)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Model: HTR-RF(20)
Smart Home Dial Thermostat
User Guide $SALUS HTR-RF$20$ Wireless Room Thermostat featured$

Introduction

HTR-RF(20) is a wireless dial room thermostat used for underfloor heating and it is compatible offline with CO10RF coordinator and online with SALUS Smart Home system (UG600/UGE600).

Product Compliance

This product complies with the essential requirements and other relevant provisions of Directives 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.saluslegal.com
2405MHz-2480MHz; <14dBm (ZigBee)

Safety Information

Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Disconnect your device before cleaning it with a dry cloth.
Note: Always isolate the AC Mains supply before installing or working on any components that require 230 VAC 50Hz supply.

Box content

$SALUS HTR-RF$20$ Wireless Room Thermostat fig1$

HTR-RF(20) Thermostat
Quick Guide

$SALUS HTR-RF$20$ Wireless Room Thermostat fig2$

2 x AA alkaline batteries
2 x fixing screws

Overlay Information

For reference only. The image on the left explains the correlation between the temperature scale and the pairing scale. To be used for the initial set-up or in case of Lost Link Error. Please keep the sticker on until installation is complete.

$SALUS HTR-RF$20$ Wireless Room Thermostat fig3$

LED Indication

$SALUS HTR-RF$20$ Wireless Room Thermostat fig4$

Only in offline mode
Note: When thermostat is calling for heating/cooling, the LED will be OFF. If you encounter the lost link error, repeat the Pairing procedure.

Installation

$SALUS HTR-RF$20$ Wireless Room Thermostat fig5$

Make your jumper settings

Jumper	Feature	Default
TPI*/SPAN	TPI (jumper ON) or Span 0.5°C (remove jumper)	TPI ON
NSB**	Night Setback ON (jumper ON) or OFF (remove jumper)	ON
Setback value***	-2°C (jumper ON) or -4°C (remove jumper)	-2°C for heating

and
+2°C for cooling

TPI will determine the pattern of your heating periods and will adjust it so that the temperature point will be maintained longer.
NSB will only operate if there is a master thermostat set on the Wiring Centre. If there is no master set, there’s no need to remove the jumper.
If you have a master thermostat connected to your system and NSB is active, NSB will automatically adjust the setback value according to the selection of the jumper.

Make sure that the thermostat dial is set in position 1.
Insert the batteries.
Check the status of the HTR-RF(20) during the first power up. Flashing RED for 2 sec = NOT PAIRED. Flashing GREEN for 2 sec = PAIRED. If HTR-RF(20) flashes green, but you need to re-pair it, please check the Reset section.

Pair (online)

Please use the online pairing method when you are using UGE600 to configure your system. Follow the on-screen instructions to complete the setup.

Go to the App
$SALUS HTR-RF$20$ Wireless Room Thermostat fig8$ $SALUS HTR-RF$20$ Wireless Room Thermostat fig9$ Optional: press the magnifying glass symbol. You can identify your device and rename it.

$SALUS HTR-RF$20$ Wireless Room Thermostat fig10$ $SALUS HTR-RF$20$ Wireless Room Thermostat fig11$ $SALUS HTR-RF$20$ Wireless Room Thermostat fig12$ $SALUS HTR-RF$20$ Wireless Room Thermostat fig13$

Dial Function

$SALUS HTR-RF$20$ Wireless Room Thermostat fig14$

In order to access the dial function menu, press the settings symbol > advanced settings > next.
Dial can change setpoint:
No – dial disabled (control through the app only)
Yes – dial can override the app setpoint

Pair (offline)

The offline pairing method should be used by non-internet users only.
WARNING! Do not use CO10RF coordinator with UGE600 simultaneously.

For more Wiring Centres, Groups or Zones please move the dial in the desired position. Note: The number of times the LED flashes green will correspond with the number of the Wiring Centre, of the Groups or of the Zones selected.

$SALUS HTR-RF$20$ Wireless Room Thermostat fig15$

Install the wiring centre according to the instructions attached to the product.

$SALUS HTR-RF$20$ Wireless Room Thermostat fig16$

Open the ZigBee network

Press the SYNC button until flashing red.
HTR-RF(20) has joined the network once the LED is solid red.
Select the Wiring Centre number (up to 9 centres)
1 WC=position 1; 2
WC=position 2; 9
WC=position 9

$SALUS HTR-RF$20$ Wireless Room Thermostat fig18$

Select the Group number
No Grouping=position 1;
Gr1=position 2;
Gr2=position 3

$SALUS HTR-RF$20$ Wireless Room Thermostat fig19$

Select the Zone number (up to 12 zones)
Zone 1=position 1;
Zone 2=position 2;
Zone 12=position 12

$SALUS HTR-RF$20$ Wireless Room Thermostat fig20$ $SALUS HTR-RF$20$ Wireless Room Thermostat fig21$ Close the ZigBee network

Identify (online)

$SALUS HTR-RF$20$ Wireless Room Thermostat fig22$

Identify (offline)

$SALUS HTR-RF$20$ Wireless Room Thermostat fig23$

Reset

$SALUS HTR-RF$20$ Wireless Room Thermostat fig24$ Read more: https://manuals.plus/salus/htr-rf20-wireless-room-thermostat- manual#ixzz8AAh5IXlx

SALUS Nordic A/S
Rønhøjvej 12,
8300 Odder, Denmark
Tel: (+45) 53534499
Email: sales@salus-controls.dk
Head Office:
SALUS Controls plc
SALUS House
Dodworth Business Park South,
Whinby Road, Dodworth,
Brandley S75 3SP, UK.
T: +44 (0) 1226 323961
E: sales@salus-tech.com
www.salus-controls.com

SALUS Controls is a member of the Compute Group
Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change specification,
design and materials of products listed in this brochure without prior notice.
For PDF Installation guide please go to www.salus-manuals.com
Issue date: Feb 2018
Version: V017