dals DCP-RMCT RGB+CCT Smart Recessed Panel Light Installation Guide
- June 12, 2024
- dals
Table of Contents
dals DCP-RMCT RGB+CCT Smart Recessed Panel Light
Introduction
Model
| Local Control| Bluetooth|
Battery
---|---|---|---
DCP-RMCT| ✔| ✔|
CR2032
ITEMS INCLUDED IN THE BOX
-
Dals Connect pro remote
-
Magnetic back plate
-
Mounting hard ware
-
CR2032 Battery
FEATURES
The Dals Connect pro remote is a user friendly extention of the Dals connect
app. you can switch your smart lights on /off, select colours, tune white and
control groups.
PARING MODE
Press and hold until the light indictors flashes.
WARRANTY
DALS offers a 5 year warranty from the date of purchase which covers repairs
or replacements of defective parts of the housing. optics. and electronics.
To contact DALS customer service call 1 877 430 1818 or send an e-mail to
[email protected].
Installation guide
BEFORE YOU START
If you wish to use a Wi-Fi connection, please ensure that your Wi-fi network
can operate on a 2.4 GHz band and that the signal is strong enough in the
desired location for the hub. Only use the included accessories.
Instructions pertaining to a risk of fire, electric shock or injury to
persons. Installation must be done according to local electrical codes.
Installation should be done by a certified electrician.
This class 8 digital apparatus complies with Canadian ICES-005. This digital
apparatus does not exceed the Class 8 limits for radio-noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
-
The Dais Connect Pro remote doesn’t require electrical connections as it is already using a battery. In the case of a retrofit installation, make the electrical connections and insert them inside the electrical box.
-
Screw the magnetic back plate onto the electrical box.
-
Remove the plastic tab from the battery of the remote.
-
Install the wall plate (not included) on the magnetic back plate. Place Dais Connect Pro Remote on magnetic back plate.
Smart connection guide
BEFORE YOU START
BEFORE STARTING INSTALLATION, SHUT THE LINE FEED POWER OFF USING THE CIRCUIT
BREAKER.
Instructions pertaining to a risk of fire, electric shock or injury to
persons. Installation must be done according to local electrical codes.
Installation should be done by a certified electrician.
This class 8 digital apparatus complies with Canadian ICES-005. This digital
apparatus does not exceed the Class 8 limits for radio-noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
-
Remove the remote from the magnetic back plate and place it on a nearby surface.
-
Download the Dais Connect app from the Apple App Store or the Google Play Store and register for a new account if this is your first time. The app requires a valid email address since it will need a verification code for you to login.
-
Configure your profile and set your home inside the app. This will allow you to control light groups and create advanced automation based on your location.
-
To initiate the pairing of your remote: Press until the indicator light flashes.
-
In the Dais Connect app, press on the”+” sign in the upper right corner and select “Add Device”. If your product support bluetooth pairing, it will show up right away at the top under “Add Device”. If you have an older Wi-Fi product. select the product from the list and follow the instructions from the app.
-
On this next step, your light will be added to the app. If you are connecting multiple products at once, they will be added in a batch. From here you can either click “Done” at the bottom, or click on the “pen” to rename the light.
-
0ptional/0ptionel Rename your light and add it to one of your rooms.
-
Control your lights! Now that a group has been assigned, use your remote to control your lights.
FCC COMPLIANCE
FCC STATEMENT
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received. including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
FCC RADIATION EXPOSURE STATEMENT:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.
IC COMPLIANCE
INDUSTRY CANADA NOTICE CAN ICES-5(“)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISED RF EXPOSURE STATEMENT
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the ISED radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm (7 .9 inches) during normal operation.
Customer Support
Download the free Dals Connect app
|
18774301818
www.dals.com