JCA35SEW01 AC Tubular Motor with Zigbee User Manual
- June 12, 2024
- JCA
Table of Contents
AC Tubular Motor with Zigbee
User Manual
Product Info
Remote Controller Buttons
Power Options
Models & Parameters (for details about other parameters, see the product nameplate)
JCA | AC Motor |
---|---|
35 | Tube Diameter: 35 mm |
S | S:Standard |
E | E: Electric limit 230V/50Hz |
EL: Electric limit 110V/60Hz
100| Torque: 10Nm
17| Speed: 17Rpm
Z| Built-in Zigbee module
**** Caution
- The power supply is AC supply.
- Please confirm the rated voltage and frequency according to the nameplate when using it.
- The motor will jog in operation, please do not proceed to the next step until it complete.
- During operation, the effective interval of the transmitter button operation is 10 seconds. If there is no effective transmitter operation for more than 10 seconds, it will automatically exit the current mode.
- The motor can be paired with max 10 controllers.
- Upper&Lower limits cannot be set at the same position, limits saved even power off.
- The motor runs constantly for at 6mins max without any other operation.
- Do not lift the motor by grabbing the wire or antenna.
Instructions
Motor head button (H) functions
Functions| Operation| Jogging time| LED lamp
flickers| Note
---|---|---|---|---
Control the UP/STOP/ DOWN of the Shade| Short press| /| /| Can only operate
after the limits are set
Adding/Removing Controller| Hold for 2s| Jog1| Flicker1| Operation needs be
done within 10s
Zigbee Connecting| Hold for 6s| Jog2| Flicker2| Entering Zigbee connection
mode
Direction Reverse| Hold for lOs| Jog3| Flicker3| All settings saved after
direction reversed
Reset| Hold for 16s| Jog4| Flicker4| All settings deleted
a.Pairing Motor with Controller
Way 1: Before adding a new controller![JCA35SEW01 AC Tubular Motor with Zigbee
- Adding](https://manuals.plus/wp-content/uploads/2023/08/JCA35SEW01-AC-
Tubular-Motor-with-Zigbee-Adding.jpg)
Way 2: After motor is powered on for more than 10s
Way 3:Power on,add controller B via pre-existing controller A b.Direction Reverse
Correct
If the limits are not set, and direction goes opposite.
If limits are set and direction goes opposite.
Note: Do reverse the direction when it goes opposite.
c.Upper &Lower Limits Setting
Note: Upper&Lower limits cannot be set at the same point.
Before limits set. the motor will run in one-touch mode by pressing Up or
Down.
hold Up or Down for 2s. motor runs in constant-touch mode.
Once limits set, press Up or Down. motor runs in constant-touch mode.
d.One-touch/Constant-touch Mode
Constant-touch ——>One-touch
Same operation can toggle from one-touch to constant -touch mode.
Note: When motor in one-touch mode, hold Up or Down for more than 2s. it
vali pun in constant-touch mode.
e.Setting and Cancelling Favorite Position
Setting
f.Hot key to the Fav. Position
Note: The Fav. position setting only can be done after upper&lower limits
set.
g.Adjusting Upper & Lower Limits
Adjust Upper limitAdjust Lower limit Note: The operation should be done within 4mins.
h.Removing Controllers
Remove a single controllerRemove controller B via pre-
existing controller ARemove all
controllers
Note: All the settings are saved even controllers removed(limits set are
saved).
Controller A/B are already paired to motor.
i.Cancelling Limits
Note: It is forbidden to run the motor if installed into the shade
without limits.
Limits should be set immediately to protect the shade.
Zigbee Connecting
*Connection requirement
Make sure the Wi-Fi module and smart phone be connected to the same Wi-Fi
network.
The smart phone needs to connect to Wi-Fi network and turn on the Bluetooth
function first
- Download APP
a.Search for “Smart Life” in the app store or scan the QR code
b.Complete account registration and login to the app
https://smartapp.tuya.com/smartlife
a. Make sure the phone is connected to the Wi-Fi network
b. Make sure the Tuya Zigbee gateway device is connected to “Smart Life” App
c. Make the motor is ready to be connected to Zigbee by following steps:
Way 1 | Way 2: |
---|
|
d. Find the added Tuya Zigbee gateway on the “Smart Life” App, click “+” to add a sub-device, and then click “LED already blink”, the APP will automatically search for motor device
e. After adding successfully, click “ ” to modify the device.
f. After the motor device is added successfully, the LED on motor head will be on for 10s and then go off.
g. Now the motor can be controlled by App from anywhere, anytime
Troubleshooting
Fault | Cause | Solution |
---|---|---|
The motor does not run or start slowly | 1. Low voltage |
2. Wrong wire connection
3. Overloading
4. Wrong installation| 1. Adjust the voltage to rated data
2. Correct the wire connection
3. Put the suitable weight for roller shade
4. Reinstall the tubular motor
The motor suddenly stop| The motr has exceeded termal overheat protection (4
minutes)| Wait for the motor to cool down for approximately 20 minutes
The motor makes a strange noise when it runs| 1. The crown and drive adapter
are not well adapterd to tube
2. The driving tube is too long, cused the brackets are too tightly| 1.
Change correct size crown and drive adapter
2. If idler is active, make driving tube shorter to avoid the tight status
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>