Nisplay N1 Tennis Ball Launcher User Manual
- June 12, 2024
- Nisplay
Table of Contents
- Nisplay N1 Tennis Ball Launcher
- INSIDE THE BOX
- WHEEL ASSEMBLY INSTALLATION INSTRUCTION
- OPERATION INSTRUCTION
- BATTERY PACK INSTRUCTION
- TRAINING MODE
- HORIZONTAL OSCILLATOR INSTALLATION INSTRUCTION
- BEGINNER’S MODE
- TROUBLESHOOTING
- SAFETY GUIDELINES
- MAINTENANCE
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Nisplay N1 Tennis Ball Launcher
INSIDE THE BOX
WHEEL ASSEMBLY INSTALLATION INSTRUCTION
- Flip the ball machine over and place it on a table or workbench.
- Position the wheel assembly on the bottom of the machine, where there are three holes. Make sure the wheel is facing the correct direction and is next to the angle of the machine.
- Use the wheel bolts provided to securely fasten the wheel assembly to the machine. Make sure the bolts a re tightened firmly.
- Repeat steps 2 and 3 to install the second wheel assembly.
OPERATION INSTRUCTION
Quick Start Guide: Please follow these quick start operating guidelines
- Connect DC Power Cord with your battery with the DC Power Input (Don the
- Control Panel (Please be aware this is a DC power input only, do NOT use AC power).
- Switch Poweron the control panel to ON.
- Adjust Feed ®to an appropriate number. (1 means launch one ball every second, 9 means launch one ball every 9 seconds).
- Adjust the Top Motor Speed to an appropriate speed®. (Higher number means higher speed).
- When Top Motor Speed is larger than Bottom Motor Speed, it will launch a topspin ball
- When Bottom Motor Speed is larger than Top Motor Speed (J) , it will launch a backspin ball
- Rotating Launch Angle®clockwise will lower the height of the ball. Rotating counterclockwise will increase the height of the ball.
- Rotate Launch Angel®will change Launch Angel Indicator®. Please adjust it to the correct angle for your need.
- After adjusting the settings. Press Start/Pause @)to Start.
- You can also use the remote controller to start or pause.
- Ball Launcher will start to launch the ball 5 seconds after you hear a “beep”.
- Ball Launcher will pause 2 seconds after you hear two II beeps II when you press the Start/Pause ® button to pause.
- Please press Start/Pause to pause and switch Power to OFF when you finish all the balls.
- FuseQ)is a self-protection system, and no action is needed.
- Now you can start and enjoy the game.
BATTERY CONNECTION INSTRUCTION (OPTIONAL)
Battery May Not be Included
- Battery Power Indicator
- Press the Test Button to show battery power from O – 100%.
- Battery DC Connector
- Use Batter Charger to connect will charge your battery.
- Connect your Ball Launch with DC Power Cord to battery will power your ball launcher.
- Battery Power Connector
- Please connect the Red wire to the red pin(+), and connect the Black wire to the black pin(-). Wrong connection will damage your battery and ball launcher and may cause fire.
- To ensure best battery lifetime
- Please place your battery evenly.
- Charge your battery fully for the first time.
- Re-charge your battery after use.
- Please do Not connect battery with ball launch when not in use.
- Re-use battery every 30 days.
- Please do not store the battery in a closed environment that exceeds 40 degrees Celsius (104 degrees F ).
Charge your battery
- You must fully charge your battery for the first use.
- The indicator will be red when charging, Green when fully charged.
- Battery life will be damaged if not used for long time.
BATTERY PACK INSTRUCTION
- Use the sticky strip to cover the Battery Power Connector side and secure your battery when you place the battery inside.
- Insert the Battery DC Connector from the hole in the case to the outside of the Battery Pack.
- Hang the Battery Pack on the ball launcher will help to transport the ball launcher.
TRAINING MODE
- The Ni splay Nl launcher depends mainly on the feed frequency, top and bottom motor speed, and the launch angel.
- The illustrations below can be used as a reference for locating the ball launcher on the court for ground strokes drills/practice.
- NOTE: Poor quality or condition of the tennis balls used or the outdoor weather conditions will also affect the need to adjust the ball launcher.
HORIZONTAL OSCILLATOR INSTALLATION INSTRUCTION
- Place the oscillator on the ground.
- Put the ball machine on top of the oscillator, making sure that the control panel side is on the same side as the oscillator handler.
- Connect the Y-splitter power cable to the battery.
- Connect one side of the Y-splitter power cable to the oscillator power input.
- Connect the other side of the Y-splitter power cable to the ball machine power input.
- Turn on the power switch for the oscillator, which will start it oscillating horizontally.
- Turn on the power switch for the ball machine and set it to “Start”.
- The ball machine will begin running.
BEGINNER’S MODE
- A is Feed Rate, which is FEED on the Control Panel (5 on the Control Panel)
- B is Top Motor Speed, which is Bottom Motor Speed on the Control Panel (6 on the Control Panel)
- C is Bottom Motor Speed, which is Top Motor Speed on the Control Panel (7 on the Control Panel)
- D is Launch Angle, which can find the Launch Angle on the Control Panel (9 on the Control Panel)
TROUBLESHOOTING
Please make sure the ball launcher is always set to OFF when you troubleshoot.
SAFETY GUIDELINES
- Please don’t stand in front of the ball launcher when it is ON.
- Please don’t touch and block the ball launcher with your body when it is ON.
- Please don’t place any non-tennis ball in the ball launcher basket when it is ON.
- Please make sure the ball launch is set to OFF when you troubleshoot or removing balls.
- Please don’t use the ball launcher in rain or wet environment.
- Please don’t move the ball launcher until it is fully off.
WARNING
- Please follow these safety guidelines to reduce the risk of electric shock, fire, and personal injury:
- Please read the user manual before using the ball launcher.
- Please don’t place any parts into water or other liquid.
- Adults must fully accompany children in use.
- Please don’t stay in front of the ball launcher when it is ON. It may cause serious injury.
- Please don’t move the ball launcher or troubleshoot when it is ON.
- Please wear safety goggles when you maintain or troubleshoot the ball launcher.
- Please don’t place any non-tennis ball in the ball launcher basket when it is ON.
- Please turn the ball launcher OFF when not in use.
MAINTENANCE
- Please clean the ball launcher periodically to remove dust and dirt.
- Use a vacuum or air blower to clean the dust and dirt.
- Use a paper or towel to wipe the external of the ball launcher.
- Please don’t use anything sharp to clean the ball launcher.
- Please don’t use water for cleaning.
STORAGE
- To ensure the lifetime and quality of the ball launcher, please follow.
- Always store the ball launcher in a clean, dry location.
- Never store the ball launcher in a closed vehicle.
- Never store the ball launcher outside that will expose it to rain and sun.
OTHER
- The product and accessories picture is just used for reference, and the actual product or accessories might be different.
- We will test and check every single machine before we ship it out, so there is a possibility there might be dust or tennis hair left on the machine.
- SCAN QR CODE TO
- DOWNLOAD THE USER MANUAL AND INSTRUCTIONS ONLINE.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>