CORSAIR iCUE NEXUS Companion Touch Screen User Manual
- June 13, 2024
- Corsair
Table of Contents
CORSAIR iCUE NEXUS Companion Touch Screen
Product Information
The iCUE NEXUS is a companion touch screen that can be connected to a PC via USB. It can be used as a standalone device with the included base or attached to a K70 RGB MK.2 or K95 RGB PLATINUM series keyboard using the provided bracket. The touch screen allows for custom graphics and functions.
Hardware Setup
- Connect the USB to the base.
- Insert the iCUE NEXUS into the base.
- Connect the base USB to the PC.
Keyboard Bracket
- Locate the bracket that matches the keyboard’s rear center panel.
- Peel off the protective film.
- Attach the bracket to the keyboard.
- Slide the iCUE NEXUS onto the bracket.
- Connect the USB to the keyboard.
Software Setup
The iCUE NEXUS supports designing custom screens with graphics and functions. Swipe left and right on the touch screen to navigate between screens. For advanced programming and product tutorials, visit www.corsair.com/nexus- faq.
Getting to Know iCUE NEXUS
- A – iCUE NEXUS
- B – Touch Screen
- C – USB Connector
- D – Standalone Base
- E – Base USB Passthrough
- F – Base USB Connector
- G – Keyboard Mounting Brackets (x3)
- H – Bracket Removal Tool
Contact Information:
- Website:corsair.com
- Phone: 888-222-4346
- Support:support.corsair.com
- Blog:corsair.com/blog
- Forum:forum.corsair.com
- YouTube:youtube.com/corsairhowto
HARDWARE SETUP
iCUE NEXUS connects to PC USB via the standalone base or when attached to a K70 RGB MK.2 or K95 RGB PLATINUM series keyboard via an included bracket.
STANDALONE BASE
- Connect USB to base
- Insert iCUE NEXUS
- Connect base USB to PC
KEYBOARD BRACKET
- Locate bracket matching keyboard rear center panel
- Peel off protective film
- Attach bracket to keyboard
- Slide iCUE NEXUS onto bracket
- Connect USB to keyboard
IMPORTANT: If attached to a keyboard, allow 24 hours for the adhesive tape on the bracket to set before using the touch screen. To remove the bracket later, turn over the keyboard and insert the included removal tool (H) into the gap between the bracket and the keyboard from the bottom side, and then gently press down to lift the bracket until it begins to detach. Hold the partially detached portion while continuing to lift different areas of the bracket until it is fully released from the keyboard. Additional brackets are available at www.corsair.com.
SOFTWARE SETUP
- iCUE NEXUS requires the iCUE software. Download iCUE from www.corsair.com/downloads and install it on your Windows® PC.
- Launch iCUE, click the iCUE NEXUS device tile, and then go to the Screens tab to begin designing your own screens with custom graphics and functions.
- Swipe left and right on the touch screen to quickly navigate between screens.
- NOTE: For more information on advanced programming and product tutorials, visit www.corsair.com/nexus-faq.
GETTING TO KNOW iCUE NEXUS
- A — iCUE NEXUS
- B — TOUCHSCREEN
- C — USB CONNECTOR
- D — STANDALONE BASE
- E — BASE USB PASSTHROUGH
- F — BASE USB CONNECTOR
- G — KEYBOARD MOUNTING BRACKETS x 3
- H — BRACKET REMOVAL TOOL
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
CAN ICES-3(B)/NMB-3(B)
Cet appareil numérique de la class B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada. CAN ICES-3(B)/NMB-3(B)
- Website:corsair.com
- Phone: 888-222-4346
- Support:support.corsair.com
- Blog:corsair.com/blog
- Forum:forum.corsair.com
- YouTube:youtube.com/corsairhowto
© 2020 CORSAIR MEMORY Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured. 49-002031 AB
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>